FacultyofElectricalEngineering VOL.8,NO.

2,2006,3237
UniversitiTeknologiMalaysia ELEKTRIKA

Voltage Sag and Mitigation Using

Dynamic Voltage Restorer (DVR) System
Shairul Wizmar Wahab and Alias Mohd Yusof *

Faculty of Electrical Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor, Malaysia.
*
Corresponding author: [email protected] (Alias Mohd Yusof), Tel: 607-5535240, Fax: 607-5566272.

Abstract: This paper highlights voltage sag as one of a power quality issue and Dynamic Voltage Restorer (DVR) is using
for mitigation of voltage sag. Voltage sag is short reduction voltage from nominal voltage, occurs in a short time which can
cause damage and loss of production especially in industrial sector. Voltage sag always related with short circuit events and
starting motor which draw very high lagging current. Since voltage sag is creating worse effects, the researchers almost keen
to find the solutions for this problem. Nowadays, a lot of devices have been developed to mitigate voltage sag such as
Dynamic Voltage Restorer (DVR), Distribution Static Compensator (D-Statcom) and Uninterruptible Power Supply (UPS).
In this paper, focus is given only on DVR system which will be simulated by using PSCAD software in order to mitigate
voltage sag. Mathematics model for calculation of voltage sag and voltage injection by DVR System also described.

Keywords: Dynamic voltage restorer, PSCAD software, Voltage sag.

sags as an rms variation with a magnitude between 10%

1. INTRODUCTION and 90% of nominal voltage and duration between
In many recent years, power quality disturbances become 0.5cycles and one minute[5].
most issue which makes many researchers interested to
find the best solutions to solve it. There are various types
of power quality which are transients, short duration
voltage variation, long duration voltage variation, voltage
imbalance, waveform distortion and voltage flicker.
Under short duration voltage variation, therere voltage
sag, voltage swell and interruption. Based on records by
Tenaga Nasional Berhad (TNB), 80% of power quality
complaints in Malaysia were traced to be related to
voltage sag [1]. Due to the increasing of new technology,
a lot of devices had been created and developed for
mitigation of voltage sag.
This paper concerns two objectives of this project
which are study on voltage sag phenomenon in power
system and mitigation this phenomenon by using
Dynamic Voltage Restorer (DVR) system. A scope of Figure 1. Voltage sag waveform
project is DVR system will be simulate by using power
system software, PSCAD/EMTDC V4. Voltage sag is happened at the adjacent feeder with
In order to carry out these objectives successfully, unhealthy feeder (Figure 2). This unhealthy feeder always
voltage sag characteristics and DVR system will be caused by two factors which are short circuits due to
discussing theoretically in details. Simulations are faults in power system networks and starting motor which
divided to three parts which are performance of DVR draw very high lagging current. Both of these factors are
system, the effects of voltage sag caused by fault in the main factor creating voltage sag as power quality
power system connected with DVR system, and finally problem in power system.
increasing performance of DVR system. Voltage sags are the most common power disturbance
which certainly gives affecting especially in industrial
2. VOLTAGE SAG and large commercial customers such as the damage of
Voltage sag is widely recognized as one of the most the sensitivity equipments and loss of daily productions
important power quality disturbances [1]. Voltage sag and finances. An example of the sensitivity equipments
(Figure 1) is a short reduction in rms voltage from are programmable logic controller (PLC), adjustable
nominal voltage, happened in a short duration, about speed drive (ASD) and chiller control.
10ms to seconds. The IEC 61000-4-30 defines the voltage There are many ways in order to mitigate voltage sag
sag (dip) as a temporary reduction of the voltage at a problem. One of them is minimizing short circuits caused
point of the electrical system below a threshold [2]. by utility directly which can be done such as with avoid
According to IEEE Standard 1159-1995, defines voltage feeder or cable overloading by correct configuration

32
 SHAIRULWIZMARWAHAB,ALIASMOHDYUSOF/ELEKTRIKA,8(2),2006,3237

planning. Another alternative is using the flexible ac

technology (FACTS) devices which have been used
widely in power system nowadays because of the
reliability to maintain power quality condition includes
for voltage sag mitigation.. There are many devices have
been created with purpose to enhance power quality such
as Dynamic Voltage Restorer (DVR), Distribution Static
Compensator (D-STATCOM) and Uninterruptible Power
Supply (UPS). All of these devices are also known as
custom power devices.
Figure 3. DVR Structure

Figure 2. Voltage sag phenomenon

3. DVR SYSTEM
Dynamic voltage restorer (DVR) is a series compensator Figure 4. DVR system in power system
which is able to protect a sensitive load from the
distortion in the supply side during fault or overloaded in
power system. The basic principle of a series 4. THE PRINCIPLE OPERATION OF DVR
compensator is simple, by inserting a voltage of required SYSTEM
magnitude and frequency, the series compensator can In normal situation without short circuit in power system,
restore the load side voltage to the desired amplitude and a capacitor between rectifier and inverter (Figure 3) will
waveform even when the source voltage is unbalanced or be charging. When voltage sag happened, this capacitor
distorted [3].This DVR device employs gate turn off will discharge to maintain load voltage supply. Nominal
thyristor (GTO) solid state power electronic switches in a voltage will be compared with voltage sag in order to get
pulse width modulated (PWM) inverter structure. The a difference voltage that will be injected by DVR system
DVR can generate or absorb independently controllable to maintain load voltage supply. PWM technique is using
real and reactive power at the load side. The DVR also is to control this variable voltage. In order to maintain load
made of a solid state dc to ac switching power converter voltage supply, reactive power must be injected by DVR
that injects a set of three phase ac output voltages in system. Practically, the capability of injection voltage by
series and synchronism with the distribution feeder DVR system is 50% of nominal voltage. It is sufficient
voltages [3]. The amplitude and phase angle of the for mitigation voltage sag because from statistic shown
injected voltages are variable thereby allowing control of that many voltage sag cases in power system involving
the real and reactive power exchange between the DVR less than 0.5 p.u. voltage drop.
and the distribution system [3]. The dc input terminal of a
DVR is connected to an energy source or an energy 5. MATHEMATICS MODEL FOR VOLTAGE SAG
storage device of appropriate capacity. The reactive CALCULATION
power exchange between the DVR and the distribution Considered Figure 5, in a normal condition (no fault),
system is internally generated by the DVR without ac current through load A and load B is equal (balance
passive reactive components. The real power exchanged load).When theres fault on feeder 1, a high current (short
at the DVR output ac terminals is provided by the DVR circuit current) will flow to feeder 1. So, based on
input dc terminal by an external energy source or energy Kirchhoffs Law, currents flow to feeder 2 will be
storage system. reduced. Consequently, voltage will also drop in feeder
DVR structure comprises rectifier, inverter, filter and 2.This voltage drop will be defined as voltage sags.
coupling transformer (Figure 3). Besides, pulse width Assume
modulated (PWM) technique is using to control variable Load A = ZLOAD_A
voltage. Filter is using for elimination harmonic Load B = ZLOAD_B B

generated from high switching frequency in PWM Feeder 1 Reactance = x1

technique. In power system network, DVR system is Feeder 2 Reactance = x2
connected in series with the distribution feeder that Current from supply source =I
supplies a sensitive load (Figure 4). Current in feeder 1 = I1
Current in feeder 2 = I2

33
 SHAIRULWIZMARWAHAB,ALIASMOHDYUSOF/ELEKTRIKA,8(2),2006,3237

When VL is considered as a reference, therefore;

Thus I = I1 + I2
In normal condition (without fault in system) V DVR = V L 0 + Z th I L ( ) Vth (8)

I=
V2
+
V2
(1) Here , and are the angle of VDVR, Zth and Vth,
x 2 + ZLOAD _ B x1 + ZLOAD _ A respectively and is the load power factor angle with
QL
When a fault happened (see Figure 5) in feeder 1, because = tan 1 .
PL
of short circuit, a high current will flow through feeder 1
as well as source current I. During this time, voltage in
The power injection of the DVR can be written as
feeder 2 decreased due to increasing of voltage drop
across source reactance xs, this makes sag happened.

SDVR = V DVR I L (9)

V2 V2
I= + (when fault happened) (2)
x 2 + ZLOAD _ B x1

Hence

V2 = Vs Ixs (3)

and V2 decreased from nominal value (V2 become as

voltage sag)

Figure 6. Calculation for DVR voltage injection

7. RESULTS AND DISCUSSION

With using PSCAD software, simulations are divided
into five parts in order to study the characteristics and the
performance of DVR system to mitigate voltage sag.

7.1 Performance of DVR System-Variable Voltage of

Supply
This part of simulation was done in order to study the
Figure 5. Calculation for voltage sag performance of DVR system in boosting the drop voltage
caused by sag voltage. Refer to IEC standard, the voltage
range is +5% to -10%. Practically, DVR has a limitation
6. MATHEMATICS MODEL FOR VOLTAGE in boosting the drop voltage. Modeling for simulation in
INJECTION BY DVR SYSTEM this part can be seeing in Figure 7. Figure 8 shows DVR
Consider the schematic diagram shown in Figure 6. structure and Figure 9 shows firing pulses for controlling
DVR system. The voltage is varied from 5kV to nominal
Zth = Rth + jXth (4) voltage, 11kV. From Table 1, we can see DVR can
provide sufficient voltage (within the power quality
VDVR + Vth = VL + ZthIL (5) requirement) for the drop voltage as low as 0.62p.u.
While for the drop voltage below 0.62p.u, DVR system
When dropped voltage happened at VL, DVR will still can boost the voltage drop but not enough to achieve
inject a series voltage VDVR through the injection to 0.9p.u of nominal voltage as the minimum power
transformer so that the desired load voltage magnitude VL quality requirement. It means for a high severity of
can be maintained. Hence dropped voltage, DVR still can boost that dropped
voltage but insufficient to achieve the desired output
VDVR = VL + ZthIL Vth (6) voltage.

PL + jQL
IL = (7)
VL

34
 SHAIRULWIZMARWAHAB,ALIASMOHDYUSOF/ELEKTRIKA,8(2),2006,3237

Table 1: Data for variable voltage of supply

Voltage (kV) Ea (p.u) Eb (p.u)
11 0.987247 0.990688
10 0.899512 0.994037
9 0.810032 0.976532
8 0.719321 0.954032
7 0.628609 0.905341
6 0.538808 0.866222
5 0.449598 0.810467

Figure 7. Modelling for variable voltage of supply 7.2 Applying Voltage Sags in Power System with DVR
Three phase fault is created on the network system
(Figure 10). Time duration for fault is (0.3-0.5)s and
breaker will isolate the unhealthy feeder at 0.5s. The
length between the feeders will determine the severity of
dropped voltage. For short distance between these
feeders, if fault occurred at one feeder, the other feeder
will face high severity for dropped voltage. For long
distance between these feeders, the severity for dropped
voltage is not too high. So, a variable length is set in this
simulation to show the severity of dropped voltage during
voltage sag phenomenon. Table 2 shows the data taken
from the simulation.
From previous section that has been discussed
(Variable Voltage of Supply), DVR can only provide
sufficient voltage for the 48% severity from nominal
voltage. As the conclusion for this simulation, the lengths
between these feeders determine the severity of drop
voltage and DVR will mitigate voltage sag phenomenon.
Mitigation voltage sag for this simulation can be observed
in Figure 11 and Figure 12.

Figure 8. DVR structure

Figure 10. Variable length for voltage sag

Figure 9. Firing pulses for PWM technique

35
 SHAIRULWIZMARWAHAB,ALIASMOHDYUSOF/ELEKTRIKA,8(2),2006,3237

In this simulation, the DC voltage is increased with

setting the transformer 1.5MVA and secondary voltage is
3kV. In doing so, changing the filter to 100uF will
produce a better filtration (doubled the value before this)
(Refer Figure 8). The result from Table 3 shows that
DVR can compensate drop voltage as low as 42% of
nominal voltage. Compared to the previous DVR system
(2KV DC voltage), it enable compensate drop voltage to
as low as 62% of nominal voltage only.
As the conclusion, with increasing DC voltage, DVR
performance for compensating the dropped voltage can
be increased.

Figure 11. Waveform of mitigation voltage sag (p.u.)

Figure 12. Waveform of mitigation voltage sag

Table 2. Variable length for voltage sag Figure 13. Increasing performance of DVR system
Length (km) Ea (p.u) Eb (p.u)
10 0.95812 0.998482
Table 3: Data for increasing performance of DVR
3 0.896826 0.993272
Voltage(kV) Ea(p.u) Eb(p.u)
1 0.763966 0.966975
11 0.97835 0.993059
0.75 0.71729 0.95369
5 0.445864 0.936014
0.5 0.651827 0.920331
4.8 0.428068 0.910269
0.1 0.547569 0.870387
4.7 0.419155 0.896031
7.3 Increasing Performance of DVR System 4 0.35688 0.788454
There are two main factors relating to the capability and
performance of DVR working against voltage sags in a
certain power system: the sag severity level and the Total 8. CONCLUSION
Harmonic Distortion (THD). Both of these in turn are In this paper, a complete simulated DVR system has been
mainly decided by the DC source [4]. developed by using the PSCAD software. Its
Based on previous discussion (Variable Voltage of characteristic and performance when applied to a
Supply), the DC voltage is coming from the transformer simulated power system has been studied. It is shown that
that the setting parameter is 1MVA and secondary the simulated DVR developed, works successfully
voltage is 2kV.Besides that, the secondary filter at without lacks in its performance when applied to a
coupling transformer is 50uF. The result shows DVR simulated power system network. By introducing DVR
only can compensate voltage for severity 48% from in the power network, it can help to improve power
nominal value. It means DVR can inject sufficient quality. It is important to have a good delivery power
voltage when the drop voltage is at least 0.62 p.u. quality in electrical power systems especially to the
There are two ways for increasing DC voltage in critical areas, such as in the industrial sectors, in order
DVR system. One of them is increasing secondary to ensure the smoothness of the daily operations.
voltage value and another one is increasing rating MVA Hopefully this paper could be a beneficial reference to
transformer. Increasing rating MVA transformer will others who are keen on voltage sag study.
draw small dropped voltage from primary to secondary
voltage. For better and higher DC result for this
simulation, both of this parameter is increased.

36
 SHAIRULWIZMARWAHAB,ALIASMOHDYUSOF/ELEKTRIKA,8(2),2006,3237

REFERENCES
[1] M. F. Faisal, Power quality management program:
TNBs Experience, Distribution Engineering
Department, TNB, 2005.
[2] A. Felce, G. Matas, Y. D. Silva, Voltage sag
analysis and solution for an industrial plant with
embedded induction motors, Inelectra S.A.C.A.
Caracas, Venezuela, 2004.
[3] A. Ghosh and G. Ledwich, Power Quality
Enhancement Using Custom Power Devices, Kluwer
Academic Publishers, 2002.
[4] P. T. Nguyen and T. K. Saha (2004), DVR against
balanced and unbalanced voltage sags: Modeling and
simulation, IEEE-School of Information
Technology and Electrical Engineering, University
of Queesland, Australia, 2004.
[5] Pirjo Heine, Matti Lehtonen, Voltage sag
distributions caused by power system faults, IEEE
Transactions on Power Systems, Vol. 18, No. 4,
November 2003.

37