RTU560

Data Sheet Rack 560SFR02

Technical Data
In addition to the general technical data of the Monitoring Connections
RTU560, the following applies:
PowerSupply WARNING

X13, X14, X15 Plug-in terminal strip,

Rack 2-pole each
19, 3 HE, 20 slots
Relay contact Normal closed contact
according DIN 41494
1 A / 60 V DC / 30 W
1 slot = 20.32 mm

Dimensions 132,8 x 482,6 x 210 mm

(H x W x D) Monitoring Connections ALARM
With boards 232 mm (D)
X11, X12 Plug-in terminal strip,
2-pole each
With boards and 280 mm (D)
connector
Relay contact Normal closed contact
1 A / 60 V DC / 30 W
Weight 2.6 kg

Printed Circuit Board

Protection Earth
Dimensions 433,7 x 132,8 mm
PE 2 * Fasten 6,3 mm
(W x H)

Operating Information
Type of Connection
Temperature -40 C +85 C
Peripheral boards Indirect, 48 pole, Type F
DIN 41612 with cut-out
Relative humidity 5 95 %
for sub-connector
non condensing
Process signal 18 pole sub-connector
connection with crimp clips
Ordering Information
23XS40R1001
23XS40R2001 560SFR02 R0001 1KGT 022200 R0001

Accessories Ordering information

Serial Interfaces
Bus Connection Unit
SPB (X1, X2) 2 *. RJ45-jack
560BCU05R0001 1KGT 022400 R0001
560BCU05R0002 1KGT 022400 R0002
Compliances

EMC EN550011, EN61000

Environmental EN60255, IEC60870
Safety EN60950

4 Doc.-No.:1KGT 150 731 V003 1

RTU560
Data Sheet Communication Unit 560CMU02 R0002

Technical Data
In addition to the RTU560 general technical data,
the following applies:

Main Processing Unit MPU Power Consumption

Microprocessor: ELAN520 @ 133 MHz 5 V DC: 1080 mA
TM
(incorporating an Intel 586
class 32 bit processor)
Mechanical Layout
RAM: 64 MByte
Printed Circuit: 3HE, Euro-card format
Flash Memory: 128 MByte (CompactFlash) (160 x 100 mm)
Front Panel: 4R, 1 slot (20 mm)
Serial Line Controller SLC
Weight: approx. 0.3 kg
Controller Type: 80C251
RAM: 32 kByte Connector Types

Dual Ported RAM: 16 kByte Subrack connector: Indirect, 48 pole

Type F DIN 41612

Serial Interfaces CP1 and CP2 Ethernet Interfaces: RJ45 jack, 8 pole

Physical Interfaces: RS232C or RS485 Serial interfaces RJ45 jack, 8 pole

RS232C:
Environmental Conditions
Bit rate: 38 400 bit/s
Temperature: -25 ... 70 C
Signal lines: GND E2/102
TxD D1/103 Relative humidity: 5 ... 95 %
RxD D2/104 (non condensing)
RTS S2/105
CTS M2/106 Ordering Information
DTR S1.2/108
DCD M5/109 560CMU02 R0002 1KGT 012 600 R0002
RS485:
Bit rate: 19 200 bit/s
Signal lines: G Signal ground
A Receive/Transmit
B Receive/Transmit

Ethernet LAN Interfaces E1 and E2

Physical Interface: 10BaseT/100BaseT
Bit rate: 10/100 MBit/s

Doc.-No.: 1KGT 150 717 V002 1 3

RTU560
Data Sheet Binary Input 23BE23

Technical Data
In addition to the RTU560 general technical data, the following applies:

Input Channels Immunity Test

Inputs 16, in 2 groups of 8 with Electrostatic 6 kV Contact
common return per group discharge 8 kV Air
Input voltage 24, 48, 60 V DC Immunity Test
log. 0: + 9 V IEC 61000-4-2 Performance criteria A
log. 1: +18 V (level 3)
Input current Typically. 2 mA Radiated Radio- 10 V/m
for 24 to 60 V DC Frequency
Electromagnetic Performance criteria A
Field Immunity
Test
Power Supply IEC 61000-4-3
Supply 5 V / 140 mA (level 3)
Immunity to 2 kV
Electrical Fast
Transient / Burst Performance criteria A
Mechanical Layout IEC 61000-4-4
Printed circuit 3HE, Euro card format (level 3)
board (160 x 100) Surge Immunity 2 kV
Front panel 4R, 1 Slot (20 mm) Test
IEC 61000-4-5 Performance criteria A
weight approx. 0.2 kg
(level 3)
Immunity to 10 V
Conducted
Connection Type Disturbances, Performance criteria A
Connector Indirect, 48 pole induced by Radio-
Frequency Fields
Type F DIN 41612
IEC 61000-4-6
(level 3)

Test Voltage
AC Test Voltage 2,5 kV, 50 Hz Environmental conditions
EN 61000-4-16 Test duration: 1 min Temperature -10 ... 70 C
IEC 60870-2-1 Relative humidity 5 ... 95 %
(class VW3) (non condensing)
Impulse Voltage 5 kV (1,2 / 50 s)
with stand test
IEC 60255-5
IEC 60870-2-1 Ordering Information
(class VW 3) Front plate Light beige
plastic
23BE23 R5001 1 KGT 012 100 R5001

Doc. No.: 1KGT 150 571 V003 1 3

RTU560
Data Sheet Binary Output 23BA20

Technical Data
In addition to the RTU560 general technical data,
the following applies:

Output Circuits Mechanical Layout

Outputs: 16, relay contacts single Printed circuit 3HE, Euro-card format
pole, 2 groups of 8 with board: (160 x 100 mm)
common return
Front panel: 4R, 1 slot (20mm)
Potential isolation: yes, group-wise, from one
another and against Weight: approx. 0.3 kg
power supply
Connection Type
Connector: indirect, 48 pole
Relay Characteristics in Connection Type F DIN 41612
with 23BA20
max. switching voltage: 60 V DC (+ 20%) Test Voltages
AC test voltage: 2.5 kV 50 Hz / VDE 804
max. switching safety electrical isolation
capacity
resistive load: 60 W Impulse voltage 5 kV (1.2/50)
withstand test: IEC 255-4 (class III)
inductive load
at L/R = 30 ms: 40 VA (at 60 VDC) Electromagnetic Compatibility
Electrical fast 1 kV
Continuous current max. 2 A transient test: IEC 801-4 (class 2)
of a relay group:
(8 with common return) High frequency 2.5 kV (1MHz)
disturbance test: IEC 255-4 (class III)
continuos current: 4A

pulse command and for command duration

23BA23 board with 25 sec.
Environmental Conditions
Temperature: 0 ... 70C
booster relay

Relative humidity: 5 ... 95 %

Power Supply (non condensing)
Supply: 5 V / 120 mA
24 V / 10 mA per relay
Ordering Information
Front plate plastic: light beige
23BA20R5312 GSNE000700R5312

Doc.-No.: 1KGT 150 403 V003 1 3

RTU560
Data Sheet Analog Input 23AE23
Technical Data Power Supply
In addition to the RTU560 general technical data, Supply: 5V / 190 mA
the following applies:
Input channels Mechanical Layout

Inputs 8 differential inputs Printed circuit 3HE, Euro-card format

board (160 x 100 mm)
Measuring 2 mA
ranges 5 mA Front panel: 4R, 1 slot (20 mm)
10 mA
20 mA Weight: approx. 0.3 kg
40 mA
2 V DC / 0 20 V DC Connection Type
Shunt / impedance 50 at 40 and 20 mA Connector: indirect 48 pole, F DIN 41612
150 at 10 to 2 mA
110 k at 2 V and 20 V DC
Electromagnetic Compatibility
Continuous load max. 80 mA
without destruction for ranges 40 and 20 mA, Electrostatic dis- 6 kV Contact
max. 40 mA charge Immunity 8 kV Air
for ranges 10/5 to 2 mA, IEC 61000-4-2
max. 38 V / max. 0.5 mA (level 3) Performance criteria A
for ranges 2 and 20 V DC
Radiated Radio- 10 V/m
AD converter 24 bit Frequency Electro-
resolution: magnetic Field Im- Performance criteria A
munity Test
IEC 61000-4-3
Resolution: 12 bit + sign = 100%,
(level 3)
all ranges except 2 V DC:
11 bit + sign for 2 V DC
Immunity to Electri- 2 kV
cal Fast Transient
Common mode Function limit
IEC 61000-4-4 Performance criteria A
voltage typ. 8 V DC
(level 3)
Absolute maximum rating
150 V DC.
Common mode rejection Surge Immunity Test 2 kV
at 0 ... 50 Hz IEC 61000-4-5
(level 3) Performance criteria A
> 70 dB at +25 C
> 60 dB at 0 ... +25C
Immunity to Con- 10 V
ducted Disturb-
Line frequency > 100 dB for fN 2%
ances, induced by Performance criteria A
interference > 45 dB for fN 10%
Radio-Frequency
suppression
IEC 61000-4-6
(level 3)
Line frequency (fN): 16.6, 50 or 60 Hz
Environmental Conditions
Error on delivery: 0.1 %
0.2 % for 2 V DC
Temperature: -10 ... 70 C
Linearity error: 0.1 %
Relative humidity: 5 ... 95 %
(non condensing)
Temperature drift: 100 ppm/K (0...70 C)

Doc.-No. 1KGT 150 573 V004 1 3