Outdoor Unit: 14-TON PURY-P168TLMU-A (-BS)

Job Name:
System Reference: Date:

UNIT OPTION
Standard Model.....................PURY-P168TLMU-A
Seacoast (BS) Model.................PURY-P168TLMU-A-BS
OUTDOOR VRF HEAT PUMP WITH ACCESSORIES
HEAT RECOVERY SYSTEM Joint Kit.............................for details see Pipe Accessories Submittal
BC Controller (required)..............for details see BC Controller Submittals
Low Ambient Kit .................for details see Low Ambient Kit Submittal
Snow/Hail Guards Kit......for details see Snow/Hail Guards Kit Submittal
Base Pan Heater Kit.............for details see Base Pan Heater Kit Submittal

Specifications Model Name

Unit Type PURY-P168TLMU-A (-BS)
Nominal Cooling Capacity (208/230V) Btu/h 168,000
Nominal Heating Capacity (208/230V) Btu/h 188,000
Cooling (Outdoor) *2 23~126 F (-5~52 C) DB
Operating Temperature Range *1
Heating (Outdoor) -13~60 F (-25~15.5 C) WB
External Dimensions (H x W x D) In. (mm) 64-31/32 x 68-29/32 x 29-5/32 (1,650 x 1,750 x 740)
Net Weight Lbs. (kg) 702 (318)
External Finish Pre-coated galvanized steel sheet
Electrical Power Requirements Voltage, Phase, Hertz 208 / 230V, 3-Phase, 60Hz
Minimum Circuit Ampacity (MCA) A 68 / 63
Maximum Overcurrent Protection (MOP) A 110 / 100
Liquid (High Pressure) 7/8 (22.2)
Piping Diameter (Brazed) (In. / mm)
Gas (Low Pressure) 1-1/8 (28.58)
Max. Total Refrigerant Line Length Ft. 1,969
Max. Refrigerant Line Length
Ft. 541
(Between ODU & IDU)
Max. Control Wiring Length Ft. 1,640
Total Capacity 50~150% of outdoor unit capacity
Indoor Unit
Model / Quantity P06~P96/1~42
Sound Pressure Levels dB(A) 61.0
Fan
Type x Quantity Propeller fan x 2
Airflow Rate CFM 11,300
External Static Pressure In. WG (Pa) Selectable; 0, 0.12 or 0.24"WG; factory set to 0"W.G.
Compressor Operating Range 12% to 100%
Compressor Type x Quantity Inverter scroll hermetic compressor
Refrigerant R410A; 23 lbs. + 2 oz. (10.5 kg)
High Pressure High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Protection Devices Inverter Circuit (Comp. / Fan) Over-current protection
Fan Motor Thermal switch
EER 10.6 / 11.2
AHRI Ratings IEER 15.9 / 19.6
(Ducted/Non-Ducted) COP 3.24 / 3.49
SCHE 24.7 / 28.3

NOTES:
*1. When applying product below -4 F, consult your design engineer for cold climate application best practices, including the use of a backup source for heating.
*2. For details on extended cooling operation range down to -10 F DB, see Low Ambient Kit Submittal.

Specifications are subject to change without notice. 2016 Mitsubishi Electric US, Inc.
 <Accessories>
Connecting pipe

NOTES:
<Low pressure>
Elbow(ID28.58(1-1/8)OD28.58(1-1/8)) P120,P144,P168 1pc.

<High pressure>

=(5-15/16)4
(23-5/8)
600=1504
Pipe (ID25.4(1)ID19.05(3/4)) P120 1pc.

740(29-3/16)

150 (5-15/16)
Pipe (ID25.4(1)OD19.05(3/4)) P120 1pc.

Pipe (ID25.4(1)ID22.2(7/8)) P144,P168 1pc.

27-4.6(3/16) Hole
(Make hole at the plastic fan guard Pipe (ID25.4(1)OD22.2(7/8)) P144,P168 1pc.

70
(2-13/16)
for snow hood attachment) 49(1-15/16)

SEACOAST PROTECTION
19.5 831(32-3/4) 831(32-3/4) 19.5 Note1.Please refer to the engineering manual for information
<Snow hood attachment hole>
(13/16) (13/16) regarding necessary spacing around the unit and
1750(68-15/16)
foundation work. Outdoor unit must be mounted at least
Top view
Discharge air 12" off the ground or 12" above the highest average snow
depth, whichever is greater.
2.At brazing of pipes,wrap the refrigerant service valve

FORM# PURY-P168TLMU-A (-BS) - 201605

303
with wet cloth and keep the temperature of
refrigerant service valve under 120C(248 F).
PURY-P120, 144, 168TLMU-A

Control box

(11-15/16)
Connecting pipe specifications

Specifications are subject to change without notice.

Intake Diameter
Intake Intake
air air
Outdoor Unit:

air Model Refrigerant pipe Service valve

High Low High Low
Service panel Service pressure pressure pressure pressure

1650(65)
panel
PURY-P120TLMU 19.05 Brazed 28.58 Brazed 25.4 28.58
5 (3/4) *1 (1-1/8) *1 (1) (1-1/8)
4

1347(53-1/16)
PURY-P144TLMU 22.2 Brazed 28.58 Brazed 25.4 28.58
8 (7/8) *1 (1-1/8) *1 (1) (1-1/8)
2 1 Fan box

77
A PURY-P168TLMU 22.2 Brazed 28.58 Brazed 25.4 28.58

(3-1/16)
(7/8) *1 (1-1/8) *1 (1) (1-1/8)

54(2-3/16)
*1 Use the included connecting pipe and connect to the refrigerant service
20 20 valve piping.

Standard: Salt Spray Test Method - no unusual rust development to 480 hours.
(13/16) (13/16) 526(20-3/4)

89
57 586(23-1/8) 57 75(3) 22-80(3-3/16)35(1-7/16) Oval hole NO. Usage Specifications

(5-3/4) 145
(8-9/16) 217
(2-1/4) (2-1/4) 541(21-5/16) 58(2-5/16) <Sling hole> 140 77 Knockout hole

(3-9/16)
Left side view 562(22-3/16) 140(5-9/16) 1 Front through hole
(5-9/16)(3-1/16)
Front view Front through hole
Refrigerant service valve Refrigerant service valve (Uses when twinning 45 Knockout hole
<High pressure> 2 For pipes
<Low pressure> kit (optional parts) (1-13/16)
is mounted.)

Sea Coast (BS): Salt Spray Test Method (JRA 9002) - no unusual rust development to 960 hours.
150 94 Knockout hole
3 Bottom through hole
23-14(9/16)20(13/16) Oval hole (5-15/16) (3-3/4)
561(22-1/8) 150(5-15/16) 62.7 or 34.5 Knockout hole
4 Front through hole (1-3/8)
(2-1/2)
516(20-3/8)

327(12-7/8)
43.7 or 22.2 Knockout hole

(10-3/8)
84
29.5

262
(3-5/16)
(1-3/16)

5 Front through hole

(1-3/4) (7/8)
For wires

Anti-corrosion Protection: A coating treatment is applied to condenser coil for protection from air contaminants.
65 Knockout hole

121 (4-13/16)
6 Bottom through hole

196 (7-3/4)
A (2-9/16)
Service valve 52 Knockout hole
7 Bottom through hole
94

( Front view ) 6 7 (2-1/16)

533(21) 140 (5-9/16) 3 34 Knockout hole
(3-3/4)

8 For transmission cables Front through hole

(1-3/8)
681(678~684)
(740)(29-3/16)
(Mounting pitch)
(26-3/4~26-15/16)

(26-13/16)

80 795(31-5/16) 795(31-5/16) 80

(5-3/4) 146
(3-3/16) (Mounting pitch) (Mounting pitch) (3-3/16)
29.5
(1-3/16)

Service valve
( Bottom view ) Bottom view
Unit: mm (in.)
PURY-P168TLMU-A (-BS) DIMENSIONS

Toll Free: 800-433-4822 www.mehvac.com

1340 Satellite Boulevard. Suwanee, GA 30024

2016 Mitsubishi Electric US, Inc.