Scribd
Upload
376 views

Lecture 24 Computer Modeling and Simulation of PWM Converter Circuits

This document discusses computer modeling and simulation of PWM converter circuits. It covers: 1. The goals of simulating converter operation to calculate performance, stresses on components, losses, and thermal requirements. 2. The challenges in power electronic simulation, including non-linear switch models, long time scales, complex feedback loops, and the need for simplification. 3. The two main approaches to simulation - using equation solvers or circuit simulators like PSPICE. PSPICE models for switches are discussed along with example simulations.

Uploaded by

lenovo1986
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
376 views

Lecture 24 Computer Modeling and Simulation of PWM Converter Circuits

This document discusses computer modeling and simulation of PWM converter circuits. It covers: 1. The goals of simulating converter operation to calculate performance, stresses on components, losses, and thermal requirements. 2. The challenges in power electronic simulation, including non-linear switch models, long time scales, complex feedback loops, and the need for simplification. 3. The two main approaches to simulation - using equation solvers or circuit simulators like PSPICE. PSPICE models for switches are discussed along with example simulations.

Uploaded by

lenovo1986
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 6

Computer Modeling and Simulation of PWM Converter Circuits

A.. Overview of Computer Simulation of Switched Converter Waveforms


1. General PWM Converter simulation goals
2. Special challenges to power electronic simulations
a. Non-linear switch conditions
b. Long time scale of the simulation
c. Need to Model Feedback loops
d. Case for Use of Simplified Models
e. Verification of Simulation with Experiment

3. A computer efficient simulation sequence is complex and artful


4. Two generic simulators for power electronics
a. Equation Solvers
b. Circuit simulators

B. Solid State Switch Models for PSPICE


1. 1. Overview
2. 2. Diode
3. 3. MOSFET
4. 4. IGBT

C. PSPICE BUCK PWM CONVERTER SIMULATION EXAMPLES


A. Overview of Computer Simulation of Switched Converter
Waveforms/Circuits
Computer aided calculation programs like Mathematica (Wolfram Research) and Matlab
(Mathworks) are useful in power electronics simulation. But the most useful circuit waveform
analysis is PSPICE (Microsim Corp.), as we shall see below. The idea is to fully simulate
the converter BEFORE starting construction and testing. Fixing problems in a model that we
invest some time and effort in, may pay for themselve’s later by spotting problems before circuit
construction begins. That is the promise of modeling, but not always the end result because of
difficulties outlined herein.
1. Goals of Converter Operation Simulation
a) Calculate both dynamic and steady state performances
of the whole PWM converter system, for all voltages and
currents versus time.

• Model power flow circuits


• Model controller response
• Model total system response with feedback loops included
b) Obtain required Vmax and Imax for all switching elements employed, so we can
better specify required switches and avoid switch failure by better knowing the
worst case switch stress conditions and planning for them.
c) Estimate power loss in various components:
1. Switches are analyzed both from the two final DC switch states and the
two dynamic switching transitions: from off to on and from on to off.
Losses effect the heat generation and associated cooling requirements
that we must meet.
d). Magnetics Losses also contribute to heat flow
requirements in addition to switch losses.

(a) Inductor’s have core losses we can estimate


(b) Transformers also have core losses e) Snubbers and Control
Electronics can be simulated to anticipate possible SOA problems of power
switches.
f) We can estimate thermal cooling for critical components using data from c and d
above. Both solid state devices and magnetic cores want to remain below 100 � C to
operate properly. So the cooling must result in ambient temperatures BELOW 100 �C
in the converter. This must be addressed.
g) We aim to speed-up converter and construction by COMPLEMENTARY simulation
together with a proof-of-concept hardware prototype. We use both to iterate to a final
design faster with fewer mistakes and a more reliable final product. That’s the goal of
simulation.

2. Challenges in Power Electronic Simulation


Unlike VLSI design we are simulating a discrete component system that has a variety of
unique switching devices with MANY parasitic elements that often dominate PWM converter
operation.
a. Accurate non-linear switch models are not always easily available, even from the
manufacturers. If available from the manufacturer’s data sheets, the data may not
always be as accurate as needed. Nevertheless, the WWW page of various
manufacturers. e.g. Motorola, Harris, Siemans, IXYS, etc offers a wealth of
information.
b. The switching time tsw is usually µ sec but the converter system response time is
seconds to minutes �lots of computer time is required to simulate PWM converter
waveforms well.
c. Chosen feedback controller models needs to be placed into the closed loop
system model. Usually both current and voltage feedback loops are employed for
PWM dc-dc converters. This complicates analysis.
d. Early on we need to choose proper simplification steps so as to model only the
immediate objectives. Limited simulation in early stages of design employs only a few
switching cycles rather than millions or more to crudely estimate voltages and currents,
which repeat with each cycle. This simplification step is very important. Often it must include
only known to be dominant parasitic elements from prior experience! ! Include expected
parasitic and circuit impedance’s on the input and output as well as line inductance 100 -
500µ H for 208 ac mains. Also, include filter capacitors, snubbers, etc.
e. Verify any model prediction by prototype PWM converter construction and testing.
f. Include the control loop model and any surprises that may arise. Choose to model
only portions of the power processor circuit rather than the full circuit in initial
simulations to save time and simulation costs.

3. The converter simulation sequence is complex


The switch model replaces a time varying circuit topology with a single time invariant two port
equivalent circuit by averaging over the switch cycle. Switch models are given by time
independent averaged characteristics over Ts. Yet, the model changes with changing choice of
duty cycle. Clearly, the frequency response of any such approximate model is limited to f < fsw.
The fact that we can even make an AC model of the PWM converter is suprising to some.
Second semester we will make just such models by small signal expansion of the DC models
we have made to date.
The f < fsw open loop power processor model A(w) Results from such an exercise. For
now just consider this small signal function as given:
Obtain transfer functions:

In practice converters all employ feedback to stabilize the output to within the user’s
specifications. The chosen controller model employed is usually available from:
1. 1. Control chip manufacturer
2. 2. Controller software

The closed loop system for the controller is then:

One employs feedback because one expects big improvements in converter performance by
using feedback including:
• Improved system stability to circuit component or switch device changes with
both temperature and aging.
• Higher Zin, Lower Zout for the closed loop system
• A low frequency model allows the use of Bode plots for determining AOL(w). From open
loop gain and phase plots versus frequency we can predict system stability as well as
instability at all operating frequencies. One can also estimate system dynamical
response to transient changes in the load or input by behavior of Aβ the loop gain near
1 I180o.
3. Two generic types of simulators are available for power electronics based simulators:
Circuit oriented and differential equation based
a) Differential Equation Based Simulators
Give total control of the solution to the non-linear differential equations that describe the PWM
circuit and then choose:
The Integration method.
Step time of simulation.
First choose only those important terms in algebraic and differential equations. Neglect as
many elements as possible for the first simulation to save computer time.
Use C language to write the program steps.
Choose your own graphical plotting tools.
b) Equation solver solution sequence
1. Circuit topology choice and switching sequence both determine loop
equations we must solve.
2. The State variable matrix format introduced in Erickson Chapter 7 is useful.
For now consider the circuit equations just in the standard state variable or matrix form:

3. The numerical solution: time step ∆ t, uses a linear interpolation


t x(t) = x(t-∆ t) +�[A(z )x(z ) + b( z )g( )]d z
z
t-D t implicitly known are the small signal equations from which we can start the process of
calculating the required integral
� �x(t) = x(t -∆ t) + 1/2 ∆ t [A(t -∆ t)x(t -∆ t) + A(t)x(t)] � Linear
+ 1/2 ∆ t [b(t - ∆ t)g(t -∆ t) + b(t)g(t)] � Algebra
Trapezoidal area approximation may be employed:

Use Matlab or Mathematica to do the numerical integration. You have complete freedom to
employ other integration algorithms as well as to change the time sequences to suit your desire
for a complete or just a crude model as we show below on page 9. The point to ponder is
whether or not you have the interest in becoming a computer programmer of power electronics
problems as this is a very time intensive endeavor.
Sample results of simple models are given on page 9 when using the Matlab
simulator.

Illustrative lines of
code in Matlab
The results are plotted below for a buck converter, which will later

With this equation based approach we see both the fast fsw waveform and the slower averaged
output waveforms for the PWM converter evolve during power up of the circuit. In this way we
could estimate any peak excursions that might cause switch failure.
b) Circuit simulators
1) Overview These simulators have been developed to a high level by the needs
of VLSI chip design over the past decades. However, the IC environment is not the power
electronics environment and we will have to take great care. A special form of commercial
circuit simulator that we will favor is termed PSPICE.

You supply: Circuit topology and nodes


Component values
Simulator Circuit equations and time evolving
generates: solutions transparent to the user for the
power processor

The key is to break out the power processor portions from the controller portions.
2) Advantages of circuit simulators
a. Fast/easy as prior library of circuits exists.
b. Segmentation into modules is also easy.
(1) Basic building block PWM converter simulation modules exist. Test each separately then
combine.
2) Easy to change the design
(1) Vary Circuit topology itself
(2) Alter Component values and component models versus f, temperature, etc.
3) Disadvantages of circuit simulators
a. No easy control over
1) Time step of simulation as for power electronics simulation times of seconds are required yet
fsw is giving Ts ≈ 10-100 µ s.
0 (2) No clear best choice of integration method for
1 numerical solution to circuit equations
.2(3) Questionable assumptions of simulator model as these are general purpose tools but
rather are often aimed at IC’s and not always modified to power electronics.

4) Commercial simulators
a. SPICE and PSPICE (student freeware)
Simulation Program with IC Emphasis (SPICE) is widely available.
It has easy to use shells and drop down menus to perform what if circuit analysis such as:
DC and AC sweep analysis,
transient response, parametric analysis of various device / component changes and finally
temperature heating analysis. Two possible starting points with limited capability as compared
to full-blown PSPICE are:
1) PSPICE version 7.1, MicroSim Corporation, 20 Fairbanks, Irvine, CA 92718.
You can also get a student version from the www. Limited to 64 circuit nodes and 30
components.
2) “Power Electronics: Computer Simulation, Analysis, and Education Using
Evaluation Version of PSpice,” on diskette with a manual, Minnesota Power
Electronics, P.O. Box 14503, Minneapolis, MN 55414.
1
2
b) ILLUSTRATIVE PSPICE ANALYSIS Circuit Schematic
L
Controller Input Data:

You might also like