Scribd
Upload
24 views

About This Guide

The document provides an overview of the features and capabilities of a DSLAM system, including ATM, DSL, routing, bridging, and management features. It describes the structure and organization of the configuration guide, and provides details on the command line interface for configuration.

Uploaded by

sushil
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
24 views

About This Guide

The document provides an overview of the features and capabilities of a DSLAM system, including ATM, DSL, routing, bridging, and management features. It describes the structure and organization of the configuration guide, and provides details on the command line interface for configuration.

Uploaded by

sushil
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

About this Guide

1.1 Structure of this guide


This guide describes how to use Command-Line Interface(CLI) to configure your DSLAM,
including, 5016 and 5024.
Do not proceed until you have completed all the hardware connections.
1.2 Purpose and Audience
The intention of this DSLAM configuration guide is the following:
] To use the Command-Line Interface(CLI) for application engineer to create a customized default
configuration for his own product design.
.
1.3 Organization
Chapter 2 System overview describes the DSLAM software feature.
Chapter 3 Basic Configurationdescribes the basic network setup and the methods to configure it.
Chapter 4 Configuring the IP Stack describes how to setup your router by configuring the IP stack.
Chapter 5 Configuring the Bridge describes how to configure the 802.1D and 802.1Q Bridge.
Chapter 6 Configuring ports describes the ports available on your device.
Chapter 7 Configuring DSL describes how to change your DSL configuration.
Chapter 8 Configuring System logging describes how to configure system logging on.
Chapter 9 Configuring RFC1483 describes how to configure RFC 1483 bridged and routed
networks.
Chapter 10 Configuring User Accounts describes how to administer the user accounts on your
network.
Chapter 11 Configuring SNMP agent describes how to configure SNMP agent.
8

2 System Overview
Features of the ISOS software is summarized as follow:
2.1 System feature
2.1.1 ATM feature
Provides adaptation layer (AAL5, AAL0) functionality(per I.363.5)
Supports UBR, CBR rt-VBR & nrt-VBR service classes in accordance with ATM forum TM 3.1.
Supports IP over ATM (IPoA, RFC 1483 & RFC 1577)
Supports Ethernet over ATM (EoA, RFC 2684 - superseding RFC 1483)
2.1.2 DSL feature
Supports fast and interleaved latency
Supports the following types of line coding:- DMT: T1.413, G.992.1, G.992.2 with auto-detection,
G.992.3 (G.dmt.bis / ADSL2) andG.992.5 (ADSL2plus)
ADSL downstream data rates up to 12 Mbps,DSL2plus data rates up to 24 Mbps
2.1.3 Routing and IP features
The software supports the following protocols:
IP layer stack supported.
Transmission Control Protocol
Address Resolution Protocol (ARP)
Internet Control Message Protocol
Routing Information Protocol (RIP) v1 and v2
IGMP, IGMP Proxy and Multicasting
TCP Maximum Segment Size (MSS) Clamp changes the MSS in the TCP header of packets, so they
do not require fragmentation when sent over a link with a smaller MTU
2.1.4 Bridging features
Layer 2 MAC Transparent bridge as specified in IEEE802.1D and 802.1Q;
Bridged PDU encapsulation (per RFC 2684)
Bridge Source MAC Address forwarding. Forwarding IPpackets based on MAC address of the packet
Spanning Tree bridge IEEE 802.1D

Chapter 2 Basic Configuration


9
IGMP Snooping support - allows multicast packets to be forwarded intelligently to ensure more efficient
use of
network bandwidth
2.1.5 Management features
EmWeb Web-based Graphical User Interface (GUI) enabling end-user device configuration via
HTTP.
Support SNMP v1, v2
SNMP MIB II, DSL MIB, ATM MIB
Command Line Interface (CLI) via serial interface or Telnet over Ethernet or DSL
Update of boot image or configuration data over HTTP/ TFTP including HTTP One-Click firmware
upgrade.
2.2 CLI overview
2.2.1 CLI features
Support local configuration by ConsoleRS-232port.
Support remote configuration by Telnet
Provide a function similar to DosKey to display history commands.
Enter ? to get online help at any time
Enter tab to match commands
2.2.1 CLI help
The Command Line interface provides online help to users:
A user can simply type ? at the Command Line prompt
A list of all the commands
?
agent Get a file from a remote host
bridge Configure layer 2 bridge.
bridgevlan
console Console access
ethernet Commands to configure ethernet transports
help Top level CLI help

You might also like