BD35F

Direct Current Compressor

R134a, 12/24V DC, 10-45V DC Solar
& 100-240V AC 50/60Hz
General
Code number (without electronic units) 101Z0200 Approvals
Electronic unit 12/24V DC - Standard 101N0212, 30 pcs: 101N0213
Electronic unit 12/24V DC - AEO 101N0340, 30 pcs: 101N0341 UL
Electronic unit 10-45V DC - Solar 101N0420, 30 pcs: 101N0421
Electronic unit 12/24V DC & 100-240V AC 50/60Hz 101N0510, 28 pcs: 101N0511 UL / VDE
Electronic unit 12/24V DC - Automotive 101N0650, 30 pcs: 101N0651 UL
Compressors on pallet 150
BD35F
Application only with BD controller
Application LBP/MBP/HBP
Evaporating temperature C -30 to 0 (10) R134a
Blue stripe serial number
Voltage range DC VDC 9.6 - 17 / 21.3 - 31.5 101Z
0200
Voltage range AC V/Hz 100 - 240 / 50/60 Barcode on white background
Made by Secop
Voltage range for solar applications VDC 10 - 45 Grey background
Country of origin or manufacturer
Max. condensing temperature continuous (short) C 60 (70)
Max. winding temperature continuous (short) C 125 (135) S = Static cooling normally sufficient
O = Oil cooling
Cooling requirements F1 = Fan cooling 1.5 m/s
Application LBP MBP HBP (compressor compartment temperature
32C S S S equal to ambient temperature)
38C S S S F2 = Fan cooling 3.0 m/s necessary
SG = Suction gas cooling normally sufficent
43C S S S
= not applicable in this area
Remarks on application: Fan cooling F1 depending on application and speed.

Motor
Motor type variable speed
Resistance, all 3 windings (25C) 2.2

Design
Displacement cm3 2.00
Oil quantity (type) cm3 150 (polyolester)
Maximum refrigerant charge g 300
Free gas volume in compressor cm3 870
Weight - Compressor/Electronic unit kg 4.3 / 0.19 (Standard)

Standard battery protection settings (refer to electronic unit Instructions for optional settings)
Voltage 12V 24V
Cut out VDC 10.4 22.8
Cut in VDC 11.7 24.2

Dimensions
Height mm A 137
B 135
B1 128
B2 73
Suction connector location/I.D. mm | angle C 6.2 | 40
material | comment Cu-plated steel | Al cap
Process connector location/I.D. mm | angle D 6.2 | 45
material | comment Cu-plated steel | Al cap
Discharge connector location/I.D. mm | angle E 5.0 | 21
material | comment Cu-plated steel | Al cap
Connector tolerance I.D. mm 0.09, on 5.0 +0.12/+0.20
Remarks:

May 2016 DES.D.100.F5.02 1/2

Capacity (EN 12900 Household/CECOMAF) 12V DC, static cooling watt Compressor speed
rpm \ C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 Electronit unit
Resistor (R1) [] Motor speed
2,000 16.0 23.8 26.7 32.9 43.7 56.5 71.8 89.8 111 121 136
2,500 18.8 29.9 33.9 41.9 55.4 71.1 89.8 112 139 152 Code number calculated values
3,000 22.4 32.9 37.1 46.1 62.5 82.2 106 133 [rpm]
3,500 27.0 35.9 40.2 50.3 69.8 93.9 122 0 2,000
Capacity (ASHRAE LBP) 12V DC, static cooling watt 101N0212 277 2,500
rpm \ C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 101N0510
101N0650 692 3,000
2,000 20.0 29.8 33.4 41.2 54.6 70.6 89.7 112 139 152 169
2,500 23.6 37.5 42.4 52.4 69.2 88.8 112 140 173 190 1523 3,500
3,000 28.1 41.3 46.5 57.9 78.2 103 132 166 0 AEO
3,500 33.9 45.1 50.5 63.1 87.3 117 153 173 2,000
101N0340
Power consumption 12V DC, static cooling watt 101N0420 450 2,500
rpm \ C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 with AEO 865 3,000
2,000 17.7 22.9 24.6 27.7 32.2 36.7 41.3 46.2 51.6 54.3 57.8
2,500 22.1 29.7 32.0 36.3 42.4 48.1 53.8 59.7 66.1 69.1 1696 3,500
3,000 29.3 34.6 36.7 41.2 48.7 56.5 64.5 72.0 In AEO (Adaptive Energy Optimizing) speed mode the BD com-
3,500 34.5 41.3 43.8 48.9 57.3 66.2 75.4 ressor will always adapt its speed to the actual cooling demand.

Current consumption (for 24V applications the following must be halfed) A

rpm \ C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 Wire dimensions DC
2,000 1.4 1.9 2.0 2.3 2.7 3.1 3.4 3.8 4.3 4.5 4.8 Size Max. length* Max. length*
2,500 1.8 2.5 2.7 3.0 3.5 4.0 4.5 5.0 5.5 5.8 Cross AWG 12V operation 24V operation
3,000 2.4 2.9 3.1 3.4 4.0 4.7 5.3 6.0 section
3,500 2.9 3.4 3.6 4.1 4.8 5.5 6.3 [mm2] [Gauge] [m] [ft.] [m] [ft.]
COP (EN 12900 Household/CECOMAF) 12V DC, static cooling W/W 2.5 12 2.5 8 5 16
rpm \ C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15 4 12 4 13 8 26
2,000 0.90 1.04 1.09 1.19 1.36 1.54 1.74 1.94 2.15 2.24 2.35 6 10 6 20 12 39
2,500 0.85 1.01 1.06 1.15 1.31 1.48 1.67 1.88 2.10 2.20 10 8 10 33 20 66
3,000 0.76 0.95 1.01 1.12 1.28 1.45 1.64 1.85 *Length between battery and electronic unit
3,500 0.78 0.87 0.92 1.03 1.22 1.42 1.62
Wire dimensions AC
COP (ASHRAE LBP) 12V DC, static cooling W/W Cross section min. 0.75 mm2 or AWG 18
rpm \ C -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 10 15
2,000 1.13 1.30 1.36 1.49 1.70 1.93 2.18 2.44 2.70 2.81 2.95 Operational errors
Error Error type
2,500 1.07 1.26 1.33 1.45 1.64 1.86 2.10 2.36 2.64 2.77 code
3,000 0.96 1.19 1.27 1.41 1.61 1.83 2.06 2.32 or LED Can be read out in the software
3,500 0.98 1.09 1.15 1.29 1.53 1.78 2.03 flashes TOOL4COOL
Test conditions with electronic units EN 12900/CECOMAF ASHRAE LBP 6 Thermostat failure
Condensing temperature 55C 54.4C (If the NTC thermistor is short-circuit or has no connection).
101N0212
101N0650

Ambient temperature 32C 32C 5 Thermal cut-out of electronic unit

Suction gas temperature 32C 32C (If the refrigeration system has been too heavily loaded, or if the
Liquid temperature no subcooling 32C ambient temperature is high, the electronic unit will run too hot).
4 Minimum motor speed error
(If the refrigeration system is too heavily loaded, the motor
Accessories for BD35F Code number cannot maintain minimum speed at approximately 1,850 rpm).
Bolt joint for one comp. :16 mm 118-1917
Bolt joint in quantities :16 mm 118-1918 3 Motor start error
(The rotor is blocked or the differential pressure in the
Snap-on in quantities :16 mm 118-1919
refrigeration system is too high (>5 bar)).
Remote kit (without cable) 105N9210
One Wire/LIN gateway 105N9501 2 Too many start attempts or fan over current
Automobile fuse, DIN 7258 12V: 15A | 24V: 7.5 A (Too many compressor or fan starts in short time or fan
DC usage: Not current higher than 0.5Aavg).
Main switch min. 20A
deliverable 1 Battery protection cut-out
Fuse, 100-240V
AC usage: from Secop
Main switch min. 6A (The voltage is outside the cut-out setting).

Secop can accept no responsibility for possible errors in catalogues, brochures and other printed material. Secop reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Secop and the Secop logotype are trademarks of Secop GmbH. All rights reserved. www.secop.com

2/2 DES.D.100.F5.02 May 2016