In-plane principal stress output in DIANA

Name: InPlanePrincipals/rosette
Path: /Examples/DianaIE/InPlanePrincipals/rosette
Keywords: analys: linear static.
class: large.
constr: suppor.
elemen: hx24l solid tp18l.
load: edge elemen force node.
materi: elasti isotro.
option: direct.
result: cauchy displa princi stress total.
 Outline

1 Why displaying in-plane principal stresses?

2 How are in-plane principal stresses determined?
3 Example
4 Finite Element Model
4.1 Units
4.2 Geometry Definition
4.3 Boundary Constraints
4.4 Properties
4.5 Loads
4.6 Meshing
5 Linear static analysis
5.1 Analysis commands
5.2 Clipping planes for contour plots
5.3 Cutting planes for tensor plots
5.4 Results
5.4.1 Load case 1 - Edge load (2D problem)
5.4.2 Load case 2 - Point load (3D problem)

In-plane principal stress output | http://dianafea.com 2/42

 1 Why displaying in-plane principal stresses?
A stress-rosette is a combination of orthogonal lines in which its lengths correspond to the absolute value of principal stresses and its orientations to
the principal directions. The lines are usually colored blue when the principal stress is negative (compression) and red when the principal stress is
positive (tension). In the principal coordinate system there are no shear stresses.

Stress-rosettes in finite element analysis are used to represent the stress paths in the models. A rosette is represented in the middle of each element.
For 2D models these representations are easy to read, because there are only two principal directions presented in planar surfaces. This is not the
case for 3D models as the rosettes have 3 orthogonal lines and are located inside the model making cloudy pictures that are very difficult to interpret
(example in [Fig. 1]).

Figure 1: Principal stress rosette output in a 3D model in Fx+ for DIANA

For this reason, DianaIE has an alternative approach: principal stresses can be projected to a surface (an outer surface of a cross-section located
inside the model). 2-dimensional rosettes with two orthogonal lines are presented in this surface resulting into readable pictures that provide the
information about stress orientations in a 3D model. These are the so-called in-plane principal stresses represented with 2-dimensional rosettes and
normal stress component displayed as contour plots.

It is a sectional representation of principal stress components that allows to see stress directions at outer and inside surfaces in the 3D model.

This tutorial explains the meaning of in-plane principal stress output in DianaIE followed by an example.

In-plane principal stress output | http://dianafea.com 3/42

 2 How are in-plane principal stresses determined?
The in-plane principal stresses are determined in the post-processing module from the stress tensor computed in the DIANA solver. The in-plane
principal stresses are computed at the middle of the element using the stress tensor averaged from the stress tensors in the respective nodes.

In a general 3D problem, the principal stresses are the eigenvalues of the stress tensor. The principal directions are the direction of the eigenvalues
(eigenvectors). Shear stresses are null in the principal directions.

zz
3
zx zy 2
xz yz

xx xy yx yy
1

xx
yy 1
zz = 2
= =
xy yx Eigenvalues = principal stresses 3
Eigenvectors = principal directions
yz = zy
zx = xz

Figure 2: Global stresses and principal stresses determined in the solver

In-plane principal stress output | http://dianafea.com 4/42

 In plane-principal stress components output in DianaIE are the principal stresses and directions projected in a given surface. These are determined
by the following steps:

1. Average the 3D stress tensor in the element from the stress tensor in the nodes;

2. Find the surface desired for the projection;

3. Rotate the averaged 3D stress tensor such that the z-axis is perpendicular to the surface [Fig. 3];

zz

zx zy y'
xz yz z' x'
z xx xy yx yy
y
x
xx 'xx
yy 'yy
zz Referential transformation 'zz
= ' = Q Q T ' = '
xy xy
yz Q is the transformation matrix
with the director cosines 'yz
zx 'zx

Figure 3: Surface for projection of principal stresses and Referential transformation

In-plane principal stress output | http://dianafea.com 5/42

 3. From the in-plane components [xx , yy , xy ] compute the 2D principal stresses and directions [1 , 2 ] that are displayed as a rosette [Fig. 4];
4. The normal stress component zz is displayed as a contour plot in the surface.

'yy '1
'yx
'xy '2
Y' 'xx
Z ' X'

In plane principals - displayed as rosette

'xx '1
'IP = 'yy Eigenvalues = principal stresses
'IP = '
2
'xy Eigenvectors = principal directions

Normal component - displayed as contour plot

'zz

Figure 4: Determination of in-plane principals and normal stress component in the output

In-plane principal stress output | http://dianafea.com 6/42

 3 Example
In the following example we will illustrate the use of in-plane principal stress output in DianaIE.

The model is a box with dimensions of height=2 m, width=1 m and length=10 m, supported at 2 end bottom edges (at begin length and at end
length) kj 0. The material is linear elastic with Youngs modulus of 30E+7 N/m2 and null Poisson ratio.

We will study 2 load-cases:

1. Edge load applied at top surface, middle length in the height direction (representing a pure 2D configuration modeled with 3D mesh) [Fig. 5]
2. Point load applied at top surface, middle length, begin width in height direction (generating torsion deformations in the model and making it
a real 3D problem) [Fig. 6].
We will perform a linear elastic analysis. We want to see the global and principal stress tensors in the box under the two load cases.

In the load case 1 (2D problem) in-plane principal stress components will directly correspond to the solver principal stresses as there is no shear
components.

In the load case 2 (3D problem) the in-plane principal stress components will differ from the solver principal stresses as the shear components are
not zero.

Figure 5: Box (2x1x10m) under edge load case Figure 6: Box (2x1x10m) under point load case

In-plane principal stress output | http://dianafea.com 7/42

 4 Finite Element Model
For the modeling session we start a new project. We will make a 3D structural model and use linear hexagonal elements.
DianaIE

Main menu File New [Fig. 7]

Figure 7: New project dialog

In-plane principal stress output | http://dianafea.com 8/42

 4.1 Units
We use meter for the unit length and Newton for force (SI Units).

DianaIE

Model Window Reference system Units [Fig. 8]

Property Panel [Fig. 9]

Figure 8: Model window Figure 9: Property Panel - Units

In-plane principal stress output | http://dianafea.com 9/42

 4.2 Geometry Definition
We start the model by making a polyline in Y = 0 and Z = 0 with the length of the block (10m) and including a vertex in the middle of the line. We
extrude this line 1 m in the Y-direction (width) [Fig. 11] and 2 m in the Z-direction (height) [Fig. 12]. We rename the shape Polyline 1 to Block
In this manner we have the block [Fig. 13] with a line in the middle of the top surface needed to define the edge load. With this procedure we also
ensure an uniform mesh.

DianaIE

Main Menu Geometry Create Add polyline [Fig. 10]

Main Menu Geometry Modify Extrude shape [Fig. 11]
Main Menu Geometry Modify Extrude shape [Fig. 12]
Geometry browser Shapes Polyline 1 <Rename to Block>

Figure 10: Geometry - Add polyline Figure 11: Geometry - Extrude polyline Figure 12: Geometry - Extrude polyline

In-plane principal stress output | http://dianafea.com 10/42

 Figure 13: View of the model - Block

In-plane principal stress output | http://dianafea.com 11/42

 We create a vertex in the middle of the bottom edge in order to later define a support condition there. To be part of the geometry we need to imprint
the vertex in the block.
DianaIE

Main Menu Geometry Create Add vertex [Fig. 14]

Main Menu Geometry Modify Projection of shapes [Fig. 15]

Figure 16: Imprint vertex - Target

Figure 14: Geometry - Add vertex Figure 15: Geometry - Imprint vertex Figure 17: Imprint vertex - Tool

In-plane principal stress output | http://dianafea.com 12/42

 4.3 Boundary Constraints
We restrain the translations in the Z-direction in both extreme edges along the width at the bottom of the block.
DianaIE

Main Menu Geometry Analysis Attach support [Fig. 18]

Figure 18: Add edge support Figure 19: View of the model - Edge support

In-plane principal stress output | http://dianafea.com 13/42

 We restrain the translations in the X-direction in one edge along the width at the bottom of the block.
DianaIE

Main Menu Geometry Analysis Attach support [Fig. 20]

Figure 20: Add edge support Figure 21: View of the model - Edge support

In-plane principal stress output | http://dianafea.com 14/42

 To prevent rigid body displacements, we restrain the translation in the Y-direction in the vertex defined in the bottom edge of the block.
DianaIE

Main Menu Geometry Analysis Attach support [Fig. 20]

Figure 22: Add point support Figure 23: View of the model - Point support

In-plane principal stress output | http://dianafea.com 15/42

 4.4 Properties
We define a linear elastic material with Youngs modulus of 3.0E+7 N/m2 and null Poisson ratio. We use solid elements and we dont need to define
geometry properties. We dont define a data set because we will use the default integration scheme.
DianaIE

Main Menu Geometry Analysis Property assignments [Fig. 24]

Shape assignment Add new material [Fig. 25] [Fig. 26]

Figure 24: Assign properties Figure 25: Add new material - Linear elastic Figure 26: Material properties

In-plane principal stress output | http://dianafea.com 16/42

 4.5 Loads
We start defining the first load case - Edge load - a vertical line load of -10 N/m applied at the top surface at middle length.
DianaIE

Main Menu Geometry Analysis Attach load [Fig. 27]

Attach load Load case Create new load case [Fig. 28]

Figure 28: Create new load case

Figure 27: Edge load Figure 29: Model view - Edge load

In-plane principal stress output | http://dianafea.com 17/42

 We define the second load case - Point load - a vertical point load of -10 N applied at the top surface at middle length, begin width.
DianaIE

Main Menu Geometry Analysis Attach load [Fig. 30]

Attach load Load case Create new load case [Fig. 31]

Figure 31: Create new load case

Figure 30: Point load Figure 32: Model view - Point load

In-plane principal stress output | http://dianafea.com 18/42

 4.6 Meshing
We set the element size as 0.15 m and generate the mesh.
DianaIE

Main Menu Geometry Analysis Set mesh properties [Fig. 33]

Main Menu Geometry Generate mesh [Fig. 34]

Figure 33: Mesh properties Figure 34: Model view - Mesh

In-plane principal stress output | http://dianafea.com 19/42

 5 Linear static analysis
5.1 Analysis commands
We set a structural linear analysis with the default characteristics.
DianaIE

Analysis browser New analysis [Fig. 35]

Analysis browser Analysis1 Add command Structural linear static [Fig. 36] [Fig. 37]

Figure 35: Analysis window Figure 36: Add command Figure 37: Analysis tree

In-plane principal stress output | http://dianafea.com 20/42

 We specify the desired output results: stresses in global and principal directions and displacements [Fig. 39]. As in-plane principal stress components
are calculated from the average element stresses, we ask also for this specific output in order to allow for a direct comparison [Fig. 40].

DianaIE

Analysis browser Analysis1 Structural nonlinear Output Edit properties [Fig. 38]
Properties - OUTPUT Result User selection Modify [Fig. 39]
Results Selection STRESS TOTAL CAUCHY GLOBAL Properties Location Element center [Fig. 40]
<do the same for the STRESS TOTAL CAUCHY PRINCI >

Figure 38: Edit output properties Figure 39: Selection of results Figure 40: Result properties

In-plane principal stress output | http://dianafea.com 21/42

 And we run the analysis.
DianaIE

Analysis browser Analysis1 Run analysis

Figure 41: Output user selection Figure 42: Run analysis

In-plane principal stress output | http://dianafea.com 22/42

 5.2 Clipping planes for contour plots
We use clipping planes to represent contour plots of stresses in different surfaces of the model. We want to study the stress state in 4 surfaces:
1. Front face Y=0 (lenght x height);
2. Back face Y=1 (lenght x height);
3. Section X=5 (height x width);
4. Section X=6 (height x width).

Y=1

Y=0

X=5
X=6

Figure 43: Surfaces for stress output representation

In-plane principal stress output | http://dianafea.com 23/42

 So, first we need to define the 4 clipping panes for these surfaces. We start by setting 4 clipping panes.
DianaIE

Results browser Result view setting Properties Contour plot settings Clip settings Add Plane 4x [Fig. 44] [Fig. 45]
<rename the 4 planes as Y=0, Y=1, X=5, X=6 (click in the names and rename)> [Fig. 46]

Figure 44: Add clipping plane Figure 45: Clipping planes Figure 46: Rename clipping planes

In-plane principal stress output | http://dianafea.com 24/42

 We now define the position of each clipping pane.

DianaIE

Contour plot settings Clip settings Y=0 Location [ 0.0 0.0001 0.0 ] , Normal [ 0 1 0 ] [Fig. 47]
Contour plot settings Clip settings Y=1 Location [ 0.0 0.9999 0.0 ] , Normal [ 0 1 0 ] [Fig. 48]

Figure 47: Clip plane settings Y=0 Figure 48: Clip plane settings Y=1

In-plane principal stress output | http://dianafea.com 25/42

 DianaIE

Contour plot settings Clip settings X=5 Location [ 5.0001 0.0 0.0 ] , Normal [ 1 0 0 ] [Fig. 49]
Contour plot settings Clip settings X=6 Location [ 6.0000 0.0 0.0 ] , Normal [ 1 0 0 ] [Fig. 50]

Figure 49: Clip plane settings X=5 Figure 50: Clip plane settings X=6

Note: For the outer surfaces we dont exactly set Y=0 and Y=1 but an approximate number to place the surfaces inside the model (Y=0.0001 and
Y=0.9999, respectively). For the X=5 surface we also give an approximate value (X=5.0001) in order move away from the symmetry point. For the
outer surfaces we could see the results without the clipping planes. However, the clipping panes we can do the contour plots only for these surfaces
and not for the entire mesh which make it easier to analyze the results.

In-plane principal stress output | http://dianafea.com 26/42

 The Enable plane option allows to activate and deactivate the view of each clipping plane. This is useful if we want to show only one plane at a time.
In the clip settings we enable the slice option to represent only the desired surface.For now we keep all clipping panes as enable (default setting). We
exemplify this with contour plots for stresses SXX [Fig. 53] where we see the results in all the clipping planes. In [Fig. 52] we can also find the global
and principal components of the stress tensor.
DianaIE
Contour plot setting Clip settings Enable (default) Slice [Fig. 51]
Results browser Output linear static analysis Element results Cauchy Total Stresses SXX [Fig. 52]
Main Menu Viewer View points Isometric view 1
Main Menu Viewer Fit all

Figure 51: Clip settings Figure 52: Result tree view - Total stresses Figure 53: SXX in the clipping planes

In-plane principal stress output | http://dianafea.com 27/42

 If we enable just one clipping plane at a time we can see the results in each surface individually.
DianaIE

Contour plot setting Y=0 Enable plane <deactivate (take the tick) from the other planes> [Fig. 54]
Contour plot setting Y=1 Enable plane <deactivate (take the tick) from the other planes> [Fig. 55]
Contour plot setting X=5 Enable plane <deactivate (take the tick) from the other planes> [Fig. 56]
Contour plot setting X=6 Enable plane <deactivate (take the tick) from the other planes> [Fig. 57]

Figure 54: SXX in plane Y=0 Figure 56: SXX in plane X=5

Figure 55: SXX in plane Y=1 Figure 57: SXX in plane X=6

In-plane principal stress output | http://dianafea.com 28/42

 Tip: It is possible to edit the clipping planes in the Graphics Window, by moving the plane with the mouse and place it in any location and direction
inside the model. We exemplify this by editing plane Y=0.
DianaIE

Graphics window Clipping panes Edit Y=0 [Fig. 58]

< In the Graphics Window move the position of the clipping plane with the mouse > [Fig. 59]

Figure 58: Edit clipping planes Figure 59: Edit clipping plane in the Graphics Window

In-plane principal stress output | http://dianafea.com 29/42

 5.3 Cutting planes for tensor plots
For the representation of the in-plane principal stresses we need to define cutting planes. In this case, we can only define a plane at a time, so we
need to change the location for each surface. The location and normal definitions are the same as defined previously for the clipping planes.
DianaIE

Results browser Result view setting Properties Tensor plot settings Cutting plane settings Enable [Fig. 60]
Cutting plane settings Location [0.0 0.0001 0.0 ] , Normal [ 0 1 0 ] (plane Y=0) [Fig. 61]
Cutting plane settings Location [0.0 0.9999 0.0 ] , Normal [ 0 1 0 ] (plane Y=1) [Fig. 62]
Cutting plane settings Location [5.0001 0.0 0.0 ] , Normal [ 1 0 0 ] (plane X=5) [Fig. 63]
Cutting plane settings Location [6.0000 0.0 0.0 ] , Normal [ 1 0 0 ] (plane X=6) [Fig. 64]

Figure 61: Cutting plane settings Y=0 Figure 63: Cutting plane settings X=5

Figure 60: Cutting plane settings Figure 62: Cutting plane settings Y=1 Figure 64: Cutting plane settings X=6

In-plane principal stress output | http://dianafea.com 30/42

 We show the location of the different cutting plates with the representation of in-plane principal components (here we can also find the normal
principal component output [Fig. 65]).
DianaIE
Results browser Output linear static analysis Element results Cauchy Total Stresses
SXX Show in-plane principal components [Fig. 65]
< change the location of the different cutting planes as in [Fig. 66] - [Fig. 69]>

Figure 66: In-plane stresses in plane Y=0 Figure 68: In-plane stresses in plane X=5

Figure 65: Result tree -

Stresses Figure 67: In-plane stresses in plane Y=1 Figure 69: In-plane stresses in plane X=6

In-plane principal stress output | http://dianafea.com 31/42

 5.4 Results
We will use the clipping and cutting planes defined previously to analyze the different stress components acting in the block. The steps for visualization
in DianaIE will not be repeated. We will focus this part of the tutorial on the discussion of the in-plane principals output.

5.4.1 Load case 1 - Edge load (2D problem)

[Fig. 70] presents the total stresses SXX in the different surfaces (see [Fig. 52]). In the following we will see the global and principal stresses and
rosettes for each surface in detail. For that we activate only one clipping plane at a time (see [Fig. 61]-[Fig. 64] and use left view of the model.

Figure 70: Total stress contours displayed in the clipping planes

In-plane principal stress output | http://dianafea.com 32/42

 We present the contour plots of the global stress tensor SXX and SZZ and of the principal stresses S1 and S3 in the front face (plane Y=0).
In [Fig. 71] we see the SXX compression (negative values in blue) and tension (positive values in red) zones in the central part, which correspond to
the principal stresses [Fig. 73] [Fig. 74] (as these are oriented in length direction).
Towards begin and end parts of the block the principal stresses rotate to the supports. SXX values are not exactly equal to S1 and S2 because there
is a concentration of SZZ [Fig. 72] in the supports and loading points. Extreme values of in-plane principals are the maximum SXX and minimum
SZZ.

Figure 71: SXX in clipping plane Y=0 Figure 73: S1 in clipping plane Y=0

Figure 72: SZZ in clipping plane Y=0 Figure 74: S3 in clipping plane Y=0

Note: As the Edge Load is symmetric, plane Y=1 (Back face) presents the same results as plane Y=0 (Front face) and is not presented for this case.

In-plane principal stress output | http://dianafea.com 33/42

 We now present the in-plane principal components as rosette and the normal principal component as contour plot (see [Fig. 65]).
By comparing [Fig. 75] with [Fig. 73] and [Fig. 74] we see that the in-plane principals correspond to the principal stresses from the solver.
In [Fig. 76] we see that the normal component is zero in the areas apart from the load concentration areas; in these areas it correspond to stress SZZ
(compare with [Fig. 72]).

Figure 75: In-plane principal stresses in cutting plane Y=0

Figure 76: Normal stress component in cutting plane Y=0

In-plane principal stress output | http://dianafea.com 34/42

 We display the stress components (global and principal) in the cross-section correspondent to plane X=5.

As this a load concentration area the in-plane principal stress components are not zero [Fig. 81]. The in-principal stresses displayed as rosettes are
approximately null in the bottom (where we have mainly SXX stresses [Fig. 77]) and approximately equal to SZZ [Fig. 78] in the top of the cross
section.
In the center length we have high SZZ stresses, so we have not null in plane stress components. The normal component show the compressive and
tension zones [Fig. 82].

Figure 81: In-plane principal stresses in

cutting plane X=5
Figure 77: SXX in clipping plane X=5 Figure 79: S1 in clipping plane X=5

Figure 82: Normal stress component in

Figure 78: SZZ in clipping plane X=5 Figure 80: S3 in clipping plane X=5 cutting plane X=5

In-plane principal stress output | http://dianafea.com 35/42

 We now display the same stress components (global and principal) in the cross-section correspondent to plane X=6 (out of the load concentration zone).

Here the in-plane principals [Fig. 87] are approximately zero because the stresses appear predominantly in XX direction. So, the normal component
[Fig. 88] is similar to the global stress SXX [Fig. 83], showing the compressive and tension zones.

Figure 87: In-plane principal stresses in

cutting plane X=6
Figure 83: SXX in clipping plane X=6 Figure 85: S1 in clipping plane X=6

Figure 88: Normal stress component in

Figure 84: SZZ in clipping plane X=6 Figure 86: S3 in clipping plane X=6 cutting plane X=6

In-plane principal stress output | http://dianafea.com 36/42

 5.4.2 Load case 2 - Point load (3D problem)

[Fig. 89] presents the Cauchy Total Stresses SXX in the different surfaces. In the following we will see the global and principal stresses and rosettes
for each surface in detail. For that, we define one clipping plane at a time (see [Fig. 61]- [Fig. 64]) and use left view of the model.

Figure 89: Contour Clips

In-plane principal stress output | http://dianafea.com 37/42

 We present the contour plots of the global and principal stresses (see [Fig. 52]) in the front face (plane Y=0) (see [Fig. 61]).

Figure 90: SXX in clipping plane Y=0 Figure 93: S1 in clipping plane Y=0

Figure 91: SYY in clipping plane Y=0 Figure 94: S2 in clipping plane Y=0

Figure 92: SZZ in clipping plane Y=0 Figure 95: S3 in clipping plane Y=0

In-plane principal stress output | http://dianafea.com 38/42

 We also present the in-plane principal components and the normal principal component.

Figure 96: In-plane principal stresses in cutting plane Y=0

Figure 97: Normal stress component in cutting plane Y=0

In-plane principal stress output | http://dianafea.com 39/42

 Now the point load generates a 3D state of stresses with torsion and the front and back faces do not have the same results as in the case of the edge
load. So we also present the contour plots of the global and principal stresses in the back face (plane Y=1) (see [Fig. 62]).

Figure 98: SXX in clipping plane Y=1 Figure 101: S1 in clipping plane Y=1

Figure 99: SYY in clipping plane Y=1 Figure 102: S2 in clipping plane Y=1

Figure 100: SZZ in clipping plane Y=1 Figure 103: S3 in clipping plane Y=1

In-plane principal stress output | http://dianafea.com 40/42

 We present the in-plane principal components and the normal principal component for this surface.
The in-plane and normal principal components at both outer faces (Y=0 and Y=1) present different results as consequence of eccentricity of loading
(compare [Fig. 96] with [Fig. 104] for in-plane components and [Fig. 97] with [Fig. 105] for normal component).

Figure 104: In-plane principal stresses in cutting plane Y=1

Figure 105: Normal stress component in cutting plane Y=1

In-plane principal stress output | http://dianafea.com 41/42

 We display the stress components (global and principal) in the cross-section correspondent to plane X=6 (out of the load concentration zone).
In the rosette representation (in-plane principals) [Fig. 112] we can observe the torsion effects in the cross section, with the circular flow of shear
stresses. The out of plane component [Fig. 113] shows the tensile and compression areas that are not always symmetric and aligned anymore. We
can also see the principal values in the cross section that present a non-symmetric pattern [Fig. 109]-[Fig. 111] (compare these with [Fig. 85] [Fig. 86]).

Figure 106: SXX in clipping plane X=6 Figure 109: S1 in clipping plan X=6

Figure 112: In-plane principal stresses in

cutting plane X=6

Figure 107: SYY in clipping plane X=6 Figure 110: S2 in clipping plan X=6

Figure 113: Normal stress component in

Figure 108: SXX in clipping plane X=6 Figure 111: S3 in clipping plan X=6 cutting plane X=6

In-plane principal stress output | http://dianafea.com 42/42