Scribd
Upload
2K views

How To Resolve RTWP Problem

Most common causes of high RTWP (Received Total Wideband Power) are issues with jumper cables, combiners, and antenna connections that can cause interference. Checking the VSWR (Voltage Standing Wave Ratio) and looking for changes in the network configuration or new activations are recommended first steps to troubleshoot high RTWP. The issue may also be external interference occurring during specific times, so monitoring hourly data over a week can help identify root causes.

Uploaded by

HTM
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
2K views

How To Resolve RTWP Problem

Most common causes of high RTWP (Received Total Wideband Power) are issues with jumper cables, combiners, and antenna connections that can cause interference. Checking the VSWR (Voltage Standing Wave Ratio) and looking for changes in the network configuration or new activations are recommended first steps to troubleshoot high RTWP. The issue may also be external interference occurring during specific times, so monitoring hourly data over a week can help identify root causes.

Uploaded by

HTM
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 4

How to Resolve RTWP Problem?

Common Solution for RTWP in Cellular Network Optimization


- Most common solution is configuration issue in RNC and RBS.
- Check Jumper cable.
- Check VSWR
- Check any new activation in RNC
Also take a one week data hourly for this analysis.Some possibility that you got
problem in some hours only.
For Ericsson System you got this value from below counters
pmSumUlRssi
pmSamplesUlRssi
eensten
01-09-2014, 03:34 PM
Want to share my experience for high RTWP problem in Indoor coverage or in build
ing coverage : Possibility can happen also in combiner device which have low qua
lity level of component which cause intermodulation. Usually happen for In BUild
ing coverage which combine multi operator. I try to change the combiner device w
ith more expesive one (high quality) the high RTWP problem become normal (reduce
to -100 or -95 dBm from -70dBm). Case Close....so please check also the combine
r and their connections. Hope is this information is useful.
BR,
eensten
sanjeru
01-23-2014, 06:24 PM
hi,
In one IBS, Mean RTWP values is high (-75dbm--60dbm) in a specific time ( 6.00pm
to 10.00pm). how could i figure it out whether it is a extenal interference or
internal interference. futher once i check the VSWR value was 1.3.
thanks
tariqehsan16
02-21-2014, 12:10 PM
Received Total Wideband Power is to be troubleshooted by checking the amount of
interference of internal or external interference in the network.
tariqehsan16
02-21-2014, 12:11 PM
Want to share my experience for high RTWP problem in Indoor coverage or in build
ing coverage : Possibility can happen also in combiner device which have low qua
lity level of component which cause intermodulation. Usually happen for In BUild
ing coverage which combine multi operator. I try to change the combiner device w
ith more expesive one (high quality) the high RTWP problem become normal (reduce
to -100 or -95 dBm from -70dBm).
tariqehsan16
02-21-2014, 12:11 PM
Hi All
Kindly provide the solution on RTWP cases in ZTE and Huawei and Ericsson..
tariqehsan16
02-21-2014, 12:12 PM
Mean RTWP values is high (-75dbm--60dbm) in a specific time ( 6.00pm to 10.00pm)
. how could i figure it out whether it is a extenal interference or internal int
erference. futher once i check the VSWR
tariqehsan16
02-21-2014, 12:13 PM
Joint Analysis of Traffic and Channel Power Distributions
in 3G Wireless Telecommunications Networks
tariqehsan16
02-21-2014, 12:14 PM
Providing capacity to keep pace with the explosive growth in wireless data servi
ces is a highly complex task, due
to the time variant and geographically inhomogeneous nature of offered traffic.
To ensure a consistent, highquality
user experience, both site and carrier density
tariqehsan16
02-21-2014, 12:17 PM
The Universal Mobile Telecommunication System reserves a range of radio frequenc
ies for the transmission of telephone calls. This band of frequencies is the "Wi
deband" in the name of RTWP. It is a finite resource and it is possible that it
can be overloaded. This is "congestion" and RTWP is a tool aimed at managing thi
s phenomenon
captx
04-15-2014, 12:51 PM
Hi,
We have checked the Combiners
VSWR
Parameters
and jumber cables.
But still the RTWP is high for the cell. What could be the issue and how to reso
lve it?
nabil zaidi
08-05-2014, 09:54 AM
hi all
actualy we this problem of RSSI in 3g network till now we dont found solution i
allways check jumpers ,, RRU fibre swap antenna but RSSI still high
dbourne89
11-14-2014, 09:45 AM
if the value is higher at a particular time then it may be external interference
.check for faulty repeaters in sorroundings
farshadr
01-06-2015, 09:42 PM
Hi,
is there any code cong or power cong in cell, how much is dedicated to HSPA
cpski02
03-30-2015, 01:54 PM
We've often found TMA's are a issue for RTWP. They will sweep and PIM test fine
but still cause RTWP.
aamamun124
04-07-2015, 12:35 PM
Hi, I got high RTWP(-850 instead of -1000) for all 3 sectors in U850. Below test
s are done: 1. When put dummy load on top of main feeders bypassing antenna , RT
WP found OK for all 3 sectors. (2) RET was changed to 10 degree, but no improvem
ent is RTWP (3) Sweeps are taken, seems normal. Any idea what is causing RTWP pr
oblem?
simohamed
10-05-2015, 08:33 PM
hi all what is the difference between the RTWP and main diversity in WCDMA
shakeel56
04-20-2016, 05:42 PM
Hi,
We have checked the Combiners
VSWR
Parameters
and jumber cables.
But still the RTWP is high for the cell. What could be the issue and how to reso
lve it?
Try to Please check mechanical tilt and azimuth of each antenna
_Prestissimo_
06-24-2016, 09:05 AM
Great tips.
Looks like most of RTWP problems are result of the jumper connections.
nastotech
02-22-2017, 01:27 PM
i have resolved the value just now, thanks to all
please use cabx command
================================================== =============================
===================== ================
Cell RX1(dBm) RX2(dBm) Delta TrDevices
================================================== =============================
===================== ================
S1C1 -85.5 -85.1 0.4 *1-1/RRUW-1/1 *1-1/RRUW-1/2
S1C2 -83.1 -83.4 0.3 *1-1/RRUW-1/3 *1-1/RRUW-1/4
--------------------------------------------------------------------------------
------------------------------------
see rssi value is -85 and -83.4
now increase this value (RX1 and RX2) to -108 if there is no combiner or TMA in
my case i have combiner so i increase the value by losing jumper connections at
RRU12 end and make VSWR high it automatically increase the RSSI Value
Now i Have
Cell RX1(dBm) RX2(dBm) Delta TrDevices
================================================== =============================
===================== ================
S1C1 -102.2 -101.8 0.4 *1-1/RRUW-1/1 *1-1/RRUW-1/2
S1C2 -100.1 -100.2 0.1 *1-1/RRUW-1/3 *1-1/RRUW-1/4
hope it will help

We've often found TMA's are a issue for RTWP. They will sweep and PIM test fine
but still cause RTWP.
nastotech
02-22-2017, 01:30 PM
Great tips.
Looks like most of RTWP problems are result of the jumper connections.
i have resolved the value just now, thanks to all
please use cabx command
================================================== =============================
===================== ================
Cell RX1(dBm) RX2(dBm) Delta TrDevices
================================================== =============================
===================== ================
S1C1 -85.5 -85.1 0.4 *1-1/RRUW-1/1 *1-1/RRUW-1/2
S1C2 -83.1 -83.4 0.3 *1-1/RRUW-1/3 *1-1/RRUW-1/4
--------------------------------------------------------------------------------
------------------------------------
see rssi value is -85 and -83.4
now increase this value (RX1 and RX2) to -108 if there is no combiner or TMA in
my case i have combiner so i increase the value by losing jumper connections at
RRU12 end and make VSWR high it automatically increase the RSSI Value
Now i Have
Cell RX1(dBm) RX2(dBm) Delta TrDevices
================================================== =============================
===================== ================
S1C1 -102.2 -101.8 0.4 *1-1/RRUW-1/1 *1-1/RRUW-1/2
S1C2 -100.1 -100.2 0.1 *1-1/RRUW-1/3 *1-1/RRUW-1/4
hope it will help

You might also like