Scribd
Upload
480 views2 pages

Heavy Hex Nuts, ASTM A194/A194M and ASME SA194/SA194M, 2HM, Plain

This document provides product standards for heavy hex nuts in accordance with ASTM A194/A194M and ASME SA194/SA194M specifications. It lists dimensional requirements for nut sizes, material and mechanical properties including a minimum hardness of 84-99 HRB, thread requirements per ASME B1.1, a light protective oil finish, and marking and testing standards including full traceability and compliance with Fastenal requirements. Suppliers are expected to meet all requirements or face potential corrective actions.

Uploaded by

Sandip Jawalkar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
480 views2 pages

Heavy Hex Nuts, ASTM A194/A194M and ASME SA194/SA194M, 2HM, Plain

This document provides product standards for heavy hex nuts in accordance with ASTM A194/A194M and ASME SA194/SA194M specifications. It lists dimensional requirements for nut sizes, material and mechanical properties including a minimum hardness of 84-99 HRB, thread requirements per ASME B1.1, a light protective oil finish, and marking and testing standards including full traceability and compliance with Fastenal requirements. Suppliers are expected to meet all requirements or face potential corrective actions.

Uploaded by

Sandip Jawalkar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2 Fastenal Product Standard REV-04

Date: January 5, 2017 HHN.2HM.P

Heavy Hex Nuts, ASTM A194/A194M and ASME SA194/SA194M, 2HM, Plain
The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order. If
the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your
status as an approved vendor. Unless otherwise specified, all referenced consensus standards must be adhered to in their entirety.

F H
Nominal
Width Across Flats Thickness
Size
Max. Min. Max. Min.
1/4 .500 .488 .250 .218
5/16 .562 .546 .314 .280
3/8 .688 .669 .377 .341
7/16 .750 .728 .441 .403
1/2 .875 .850 .504 .464
9/16 .938 .909 .568 .526
5/8 1.062 1.031 .631 .587
3/4 1.250 1.212 .758 .710
7/8 1.438 1.394 .885 .833
1 1.625 1.575 1.012 .956
1 1/8 1.812 1.756 1.139 1.079
1 1/4 2.000 1.938 1.251 1.187
1 3/8 2.188 2.119 1.378 1.310
1 1/2 2.375 2.300 1.505 1.433
1 5/8 2.562 2.481 1.632 1.556
1 3/4 2.750 2.662 1.759 1.679
1 7/8 2.938 2.844 1.886 1.802
2 3.125 3.025 2.013 1.925
2 1/4 3.500 3.388 2.251 2.155
2 1/2 3.875 3.750 2.505 2.401
2 3/4 4.250 4.112 2.759 2.647
3 4.625 4.475 3.013 2.893
3 1/4 5.000 4.838 3.252 3.124
3 1/2 5.375 5.200 3.506 3.370
3 3/4 5.750 5.562 3.760 3.616
4 6.125 5.925 4.014 3.862
Page 2 of 2 Fastenal Product Standard REV-04

Date: January 5, 2017 HHN.2HM.P

Specification Requirements:

Dimensions: ASME B18.2.2


Material &
Mechanical Properties: Grade 2HM of ASTM A194/A194M and ASME SA194/SA194M
UNF shall have the same proof load as UNC. Sizes larger than 1-1/4
nominal diameter shall be accepted if meeting the hardness requirement
of 84-99 HRB, using the prescribed test method of ASTM A370.
Thread Requirements: ASME B1.1, UNC & UNF, or UN8, Class 2B
Finish: Light Protective Oil
Product Marking: Manufacturer ID and 2HM (or 2HMB when
manufactured from bar stock)
Material Test Reports: The MTR must have documented lot traceability, dimensional
results, full chemical test results and full mechanical test results
to the specification(s) above. Each lot shall show evidence of having
been 100% hardness tested (each nut). In addition, the MTR shall be in
full compliance with Fastenals MTR Requirements.

You might also like