Subject APPROVED DOCUMENT B (FIRE 14B

Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/10/10 Rev Page 1

A new updated version of Approved Document B comes into force from the 6th April 2007.

This revised guidance is split into two separate documents:-

Volume 1 Dwelling Houses
Volume 2 Buildings other than Dwelling Houses

Transitional Provisions.
Applications for any new building work that are made on or after 6th April 2007 will be required to follow the
new guidance.
This Guidance Note covers the main changes to Volume 2 Buildings other than Dwelling Houses.

Flats are not included in this guide but are covered by this Approved Document.
Rather than go through every provision of the new guidance, the main changes will be identified and guidance
provided.
Reference should be made to the full versions of the documents, which can be downloaded from Tameside
Web Page (link).

SPRINKLER SYSTEMS.
The document has expanded the guidance on sprinklers, which can significantly reduce the risk to life and
degree of damage incurred in a fire.
Sprinkler protection can be used as compensatory features against some of these Approved Documents
Recommendations.
As a general rule, sprinkler protection should be provided throughout the building where it is intended to be
provided. However, where the sprinklers are being installed as a compensatory feature to address a specific
risk or hazard, it may be accepted to only part of the building, for instance a separated part or separate fire
compartment.

Systems to be designed and installed in accordance with:

(a) For dwellings and residential buildings BS 9251:2005 Sprinkler systems for residential and domestic
occupancies
(b) For non-residential buildings or dwellings and residential buildings outside the scope of BS 9251, either
i) the requirements of BS 5306-2:1990, including the relevant hazard classification, together with the
additional requirements for life safety.
ii) the requirements of BSEN12845:2004 including the relevant hazard classification together with the
special requirements for life safety systems.

NOTE: Any sprinkler system installed to satisfy Part B requirements must be a LIFE SAFETY SYSTEM.
However, there may be some circumstances where a particular life safety requirement, specified in BS 5306-2
or BS EN 12845 is inappropriate or unnecessary.

1
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/10/10 Rev Page 2

Water supplies for non-residential sprinkler should consist of either:

(a) For systems designed and installed to BS5306-2:
(i) 2 single water supplies complying with clause 13.1.2 where each is independent of the other; or
(ii) 2 stored water supplies, where:
(1) gravity or suction tanks should be either Type A, Type D or their equivalent (clause 17.4.11.5); and
(2) any pump arrangements should comply with BS 5306-2 clause 17.4.1.5; and
(3) the capacity of each tank should be equivalent to at least half the specified minimum water volume
of a single full capacity tank, appropriate to the hazard; or
(4) one tank should be equivalent to half the specified water volume of a single full capacity tank and
the other shall not be less than half the minimum volume of a reduced capacity tank (see Table
25), appropriate to the hazard; and

NOTE: the requirements for inflow should be met.

(5) whichever water storage arrangement is used at (3) or (4) above, the total design capacity of the
water supply, including any inflow for a reduced capacity tank should be at least equivalent to a
single full holding capacity tank complying with Table 21, 22, 23 or 24, as appropriate to the
hazard and pipework design.

(b) For systems designed and installed to BS EN 12845;

(i) 2 single water supplies complying with clause 9.6.1 where each is independent of the other; or
(ii) 2 stored water supplies, where:
(1) gravity or suction tanks should satisfy all the requirements of clause 9.6.2(b)other than
capacity; and
(2) any pump arrangements should comply with clause 10.2; and
(3) the capacity of each tank is equivalent to half the specified minimum water volume of a single
full capacity tank, appropriate to the hazard; or
(4) one tank should be at least equivalent to half the specified water volume of a single full
capacity tank and the other shall not be less than the minimum volume of a reduced capacity
tank clause 9.3.4 appropriate to the hazard; and
NOTE: the requirement for inflow should be met.

(5) whichever water storage arrangement is used at (3) or (4) above, the total capacity of water
supply, including any inflow for a reduced capacity tank should be at least equivalent to a
single full holding capacity tank complying with Table 9, 10 or clause 9.3.2.3 as appropriate to
the hazard and pipework design.

Where pumps are used to draw water from 2 tanks, then each pump should be arranged to draw water from
either tank and arranged so that any one pump on either tank could be isolated.

The sprinkler water supplies should generally not be used as connections for other services or fixed fire
fighting systems.

2
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 3

INCLUSIVE DESIGN.
Fire safety aspects of the Building Regulations apply to all persons, including people with disabilities.
Fire safety measure must be incorporated into a building taking in to account people of all ages and disabilities.
The guidance offered covers most reasonable standard provision, however, there may be some situations
where additional measures may need to be provided to accommodate special needs of certain groups of
people.

Healthcare Premises.
HTM 05 Firecode should be used for the design of hospitals and similar health care premises.

Schools.
Schools should now be designed in accordance with Building Bulletin 100. Part B will typically be satisfied
where the life safety guidance in this document is followed.

Sheltered Housing.
Many of the provisions set out in this guide for flats are applicable to sheltered housing, however, the
occupancy nature may necessitate some additional fire protection measures dependent upon the form of
development.

3
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2 .
Guidance Note Issued 01/01/07 Rev Page 4

FIRE ALARMS TO BUILDINGS OTHER THAN FLATS.

Depends upon type of occupancy and means of escape strategy (e.g. simultaneous, phased or progressive
horizontal evacuation).
Sleeping areas constitute a higher risk to occupants.
General guidance on A.F.D. systems can be found in Table A1 of BS 5839-1:2002.

Fire Alarm Systems.

All building to have arrangements for detecting fire.

SMALL BUILDINGS / PREMISES this could be a simple method of raising an alarm, e.g. if all occupants
can see and hear each other shouted warnings may be sufficient. It must be determined that the warning
can be heard and understood throughout the premise including for example in toilets, etc.
Manual sounders could be an improvement, i.e. gongs/hand bells may also be appropriate.
A simple manual call point combined with a bell, battery and charger would obviously be better still.

IN ALL OTHER CASES building should be provided with a suitable electrically operated fire alarm system
with manual call points sited adjacent to exit doors and sufficient sounders to be clearly audible throughout the
building, e.g. in compliance with BS 5839-1:2002.

BS 5839-1 specifies 3 categories of system: L protection of life / M manual alarm systems / P

protection of property.

Category L is sub-divided into:

L1 - systems installed throughout the protected building.
L2 - systems installed in only defined parts of the protected building (normally includes the coverage offered
by an L3 system)
L3 - systems designed to give warning of a fire to allow escape before escape routes become impassable
due to a fire.
L4 - systems installed within those parts of the escape routes comprising circulation areas and circulation
spaces, such as corridors and stairways; and
L5 - systems in which the protected area(s) and/or the location of detectors is designed to satisfy a specific
fire safety objective (other than that of a L1, L2, L3 or L4 system).

Type P systems
P1 - systems installed throughout the protected building.
P2 - systems installed only in defined parts of the protected building.

Call points for electrical alarm system to comply with BS 5839-2:1983 or Type A BS EN54-11:2001 and be
installed in accordance with BS 5839-1. Type B call points only to be used with approval of Building Control.

Type A call points (direct operation triggering immediate alarm activation)

Type B call points (indirect operation alarm will only be triggered when a separate manual
operation of the operating element by the user after the frangible element is
broken or displaced.
4
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note
Issued 01/01/07 Rev Page 5

To improve occupants response to an alarm activation, voice alarm systems have significant benefits in
advising occupants of an alarm situation. BS 5839-8:1998 provides guidance.
Fire alarm warning systems must be distinct from other signals, which may be in general use.
In certain premises, e.g. large shops, places of assembly, an initial alarm may be undesirable because of the
number of members of the public present. The need for fully trained staff to effect pre-planned procedures for
safe evacuation will therefore be essential. Activation of the fire alarm system will cause staff to be alerted,
e.g. by discreet sounders, personal paging systems. Provision will normally be made for full evacuation of the
premises by sounders or a message broadcast over the public address system. In all other respects, any staff
alarm systems should comply with BS 5839-1.

Warnings for People with Impaired Hearing.

Suitable method of warning (e.g. a visual and audible fire alarm signal) should be provided in buildings where it
is anticipated that one or more persons with impaired hearing may be in relative isolation (e.g. hotel bedrooms
and sanitary accommodation) and where there is no other suitable method of alerting them.
In buildings such as schools, colleges and offices where the population is controlled, a vibrating paging system
may be more appropriate useful for alerting people with other disabilities as well.
Clause 18 BS 5839-1:2002 provides guidance.

Automatic Fire Detection and Fire Alarm Systems.

Institutional and other residential occupancies to have an automatic fire detection and alarm system fitted in
accordance with BS 5839-1.
Automatic fire detection systems are not normally needed in non-residential occupancies. However, there are
often circumstances where a fire detection system, in accordance with BS 5839-1, may be needed.
e.g. a) to compensation for some departure from guidance in the Approved Document;
b) as part of the operating system for some fire protection systems, such as pressure differential
systems, smoke control systems or automatic door releases, etc.,
c) where fires can start and develop unobserved in unoccupied areas, e.g. basements/stores, etc.,
and could prejudice the premises means of escape.

Atrium buildings refer to BS 5588-7:1997 for the systems design.

Design and Installation of Systems.

Systems must be designed, installed and commissioned in accordance with the appropriate British Standard.
Commissioning certificates must be provided on completion.

Interface between fire detection and fire alarm systems and other systems.
Fire detection and fire alarm systems are sometimes used to initiate the operation, or change of state of other
systems, e.g. smoke control systems, fire extinguishing systems, door releases, etc.
To ensure adequate means of escape is maintained, the interface between systems must have a high degree
of reliability.
Particular care should be taken if the interface is facilitated via another system. Where any part BS 7273
applies to actuation of other systems), the recommendations of that standard should be followed.
5
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 6

B1 - Means of Escape.
Schools references now removed throughout as now covered by Building Bulletin 100.

3.7 Active Control Measure.

Measures incorporated into the design of a building to restrict access to the building or parts of it should not
adversely affect fire safety provisions.
Whilst it may be reasonable to secure some escape routes outside of normal business hours, the measures
left in place should be sufficient to allow safe evacuation of any persons left inside the building (see para 5.11).

Table 2 Limitations on Travel Distance.

Industrial and storage

purpose groups now have
Normal and Higher Hazard
maximum travel distances.

6
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 7

Note 5 - explains what are Higher hazards.

Diagram 15 Travel Distance in Dead-End Condition.

Requirement to add 2.5o divergence for every metre travelled in dead end has been deleted.

7
 .
Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 8

Open Spatial Planning.

3.12 and diagram 14 added

Escape routes should not be prejudiced by openings between floors, such as an escalator (see diagram 14).

An escape route should not be within 4.5m of the openings unless:

(a) the direction of travel is away from the opening; or

(b) there is an alternative escape route which does not pass within 4.5m of the open connection.

8
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 9

Width of Escape Routes and Exits.

Table 4 remains the same but the rules for measuring door clear width has changed, resulting in wider
requirements now same as Approved Document M.

APPENDIX C Methods of Measurement - Door Clear Widths.

Now measured the same as a disabled doorset new diagram C1 this will result in the doors having to be
wider than previously accepted for means of escape purposes.

9
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 10

APPENDIX C Methods of Measurement.

This is relocated from front of old document and has been updated.
Table C1 floor space factors have been updated as indicated.

Item 1 Bar areas (within 1m of serving point)

Item 2 and Bar areas without fixed seating

Note 5 refers to determining floor space factors from concourses by Football Licensing Authority for
concourses in sports ground.

10
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 11

Calculating Exit Capacity.

3.23 new requirement.
Where a ground floor storey exit shares a final exit with a stair via ground floor lobby, the width of the final exit
should be sufficient to enable a maximum evacuation flow rate equal to or greater than that from the storey exit
and stair combined (see Diagram 15)

This can be calculated from the following formula:

W = ((N/2.5 + (60 S))/80
Where:
W= width of final exit, in metres
N= number of people served by ground floor storey exit
S= Stair width in metres

Note: where the number of persons (N) entering the lobby from the ground floor is more than 60 then the
distance from the foot of the stair, or the storey exit, to the final exit should be 2m minimum.

Where this cannot be achieved then the width of the final exit (W) should be no less than the width of the stair
plus the width of the storey exit.

Worked Example:
Ground floor storey exit 250 persons share a common final exit with 1.2m wide stair
Required final exit = ((250/2.5) + (1.2 x 60))/80 width (metres) = 2.150m

11
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 12

Protected Corridors.
3.24 Clarification added that recesses and extensions not exceeding 2m deep are not treated as dead end
conditions.

3.26 - Sub-Division of Corridors.

Additional guidance added to buildings of Purpose Groups 2 to 7 requiring cavities above corridor smoke
control sub division doors to have either of the following:
(a) Fitting a cavity barrier on the line of the enclosure(s) to and across the corridor (refer to Diagram 16(a)); or
(b) Sub-dividing the storey using fire resisting construction passing through the line of the corridor sub-
division (see Diagram 16(b)).
Any void above this sub-division should be fitted with cavity barriers on the line of sub-division of the
storey and the corridor; or
(c) enclosing the cavity on the lower side by a fire resisting ceiling which extends throughout the building,
compartment or separate part.

Any door which could provide a path for smoke to bypass the sub-division should be made self-closing (but
need not necessarily be fire resisting).

12
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
Issued 01/01/07 Rev Page 13

Small Premises.
Completely new section bringing in BS 5588-11 provisions into the Approved Document.

They do not apply to premises used principally for the storage and/or sale of highly flammable liquids or
materials.
In covered shopping complexes you must refer to small units design requirements in BS 5588-10.
Requirements:
(a) Premises to be in single occupancy and to comprise of no more than a basement, a ground floor and a
first floor. Maximum 280m2 floor area to each storey (see dia 18).
(b) Kitchens or other cooking arrangements to be sited at the extremity of any dead end and be remote
from the exits; and
(c) Planned seating accommodation or assessed standing accommodation (see Table C1) for small
premises comprising a bar or restaurant should not exceed 30 persons per storey. This can be
increased on the ground storey to 100 if it has an independent final exit.

13
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
Issued 01/01/07 Rev Page 14

Construction:
1. Floor areas to be generally undivided (except for kitchens, ancillary offices and stores) ensure that
exists are clearly visible from all parts of the floor areas.
2. Store rooms to be enclosed in fire resisting construction.
3. Sufficient glazed area to be provided in any partitions separating a kitchen or ancillary office from the
open floor area to enable inner room occupants to obtain early visual warning of a fire outbreak or
provide automatic fire detection in access room area.

Distance of Travel and Number of Escape Routes.

Escape routes from any storey so that limits set in Table 5 are complied with to the nearest storey exits.

Note: The distance of travel in small premises with an open stairway is measured to the foot of the stair in a
basement or to the head of the stair in the first storey.

The siting of 2 or more exists or stairs should be such that they afford effective alternative directions of travel
from any relevant point in a storey.

Design for Vertical Escape Clause 4.6 - Single Escape Stairs in Small Premises
Single stair may be used from:
(a) small premises (previously described above), other than bars or restaurants.
(b) an office building comprising N.MT 5 storeys above ground storey, provided that:
(i) all travel distances comply with one direction restrictions in table 2 above.
(ii) every storey at a height greater than 11m has an alternative means of escape.
(c) A factory comprising NMT:
(i) 2 storeys above ground storey (normal risk building) provided all travel distances comply with
single direction restrictions above; or
(d) Process plant buildings with NMT 10 occupants.

14
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
Issued 01/01/07 Rev Page 15

Protection of escape stairs - 4.33 - Small Premises.

A small premises stair (not a bar or restaurant) may be open if it does not connect more than 2 storeys and
delivers into the ground storey NMT 3m from the final exit (see diagrams 22 and 23) and either;
(a) the storey is also served by a protected stairway; or
(b) it is a single stair in a small premise with the floor area in any storey not exceeding 90m2 and, if the
premises contains 3 storeys, the stair serving either the top or bottom storey is enclosed with fire resisting
construction at the ground storey level and discharges to a final exit independent of the ground storey
(see diagram 23).

15
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Issued 01/01/07 Rev Page 16

RESIDENTIAL CARE HOMES. New guidance section.

Fire Strategy design of these types of premises is dependent upon the way the building is designed, furnished,
staffed and managed, and the level of dependency on the residents.
Care homes for elderly will rely on a degree of assisted evacuation as such these should be designed for
progressive horizontal evacuation.
For other types of care home, a judgement has to be made as to whether progressive horizontal evacuation
should be followed.
Whatever fire strategy is chosen, this must be recorded and communicated to the building management to
ensure that procedures are adopted that are compatible with the building design.
For more complicated care homes/hospitals FIRECODE documentation should be followed.

Planning for Progressive Horizontal Evacuation.

Areas of residential care to be sub-divided into protected areas separated by compartment walls and floors
thereby allowing horizontal escape into adjacent compartments.

Each storey used for residential care to be divided into minimum 3 protected areas by compartment walls
and all floors should be compartment floors.

Every protected area is to have minimum 2 exits to adjoining, but separate protected areas. Travel distance
not to exceed Table 2 distance.

The maximum travel distance from any point to be no more than 64m to a storey exit or final exit.

A fire in any one protected area should not prevent the occupants of any other area from reaching a final
exit (see diagram 19).

16
 Escape routes should not pass through ancillary accommodation (as listed below).

Number of residents beds in a protected area to be established based on an assessment of levels of

staffing available and the level of assistant the residents require.

In no case should this exceed 10 beds in any one protected area.

Adjoining protected areas into which horizontal evacuation may take place should each have a floor area
sufficient to accommodate their own residents and the evacuated residents from the largest adjoining
protected area.

Fire Detection.
L1 BS 5839-1:2002 fire alarm and detection system to be installed.

Bedrooms.
All bedrooms to be enclosed in fire resisting construction, with fire doors and every corridor serving
bedrooms should be a protected corridor.

Bedrooms are not to contain more than 1 bed (including double bed).

Ancillary Accommodation.
To be enclosed in fire resisting construction, e.g.
a) chemical stores;
b) cleaners stores;
c) clothes storage;
d) day rooms
e) smoking rooms;
f) disposal rooms;
g) plant rooms;
h) linen stores;
i) kitchens;
j) laundry rooms;
k) staff changing and locker rooms; and
l) store rooms.

Door Closing Devices.

Specification of door closing devices must take account of the residents needs, particularly where they would
present an obstacle to the residents then the following hardware in accordance with BS EN 1155:1997 would
be appropriate:
Bedrooms - free swing door closers / Circulation spaces - hold open devices

Sprinkler Systems.
Where sprinklers are installed, the following variations can be made:
(a) Fire doors to bedrooms do not need self-closers.
(b) Protected areas may have more than 10 beds.
(c) Bedrooms may contain more than one bed.

Note: Management procedure will need to take account of the larger number of residents that may need
assistance and the need to manually close bedroom doors during sleeping hours.

17
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note
Issued 01/01/07 Rev Page 18

Provisions of Disabled Refuges.

Disabled refuges should be provided for each protected stairway from each storey, except storeys consisting of
plant rooms. Refuges do not necessarily have to be located within the stair enclosure, but should have direct
access to the stair.

Number of refuge spaces do not have to match the number of wheelchair users in the building.

Refuges are intended to form part of a management plan to evacuate disabled persons from the building.

Provisions
(a) Refuges formed by fire compartments (see dia 20)

(b) Refuges formed by protected lobby, protected corridor or protected stairway (see dia 21)

18
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note
Issued 01/01/07 Rev Page 19

(c) An area in open air such as a flat roof, balcony, podium or similar place, which is sufficiently protected
(or remote) from any fire risk and provided with its own means of escape.

Refuges to be at least 900mm x 1400mm to allow a wheelchair to be parked clear of the normal escape route
widths and should not reduce any escape routes or obstruct the flow of persons making escape.

Refuges and evacuation lifts must be suitably signed and where in a lobby or stairway area to be marked and
signed Refuge Keep Clear.

Communication.
To facilitate evacuation of persons in refuges, an emergency voice communication (EVC) system should be
installed. This allows persons in refuge to alert others and to receive reassurance that assistance is coming.

EVC to comply with BS 5839-9:2004. Type B outstations communicating with a master station in the building
control room (if one exists) or adjacent to the fire alarm panel.

This EVC can be wireless.

19
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note
Issued 01/01/07 Rev Page 20

Phased Evacuation.
4.27 Buildings over 30m with phased evacuation strategy design to consider the interaction of fire fighters
with people escaping the building this could be discounting of stairs.

GENERAL PROVISIONS.
Doors on Escape Routes.
Additional guidance on electronic security devices to doors.
5.11 Doors on escape routes where secured against entry when the building or part is occupied, it should
only be fitted with a lock or fastening which is readily operated, without a key, from the side approached
by people making their escape.
Doors operated by codes/swipe cards, etc., must be overriddable from the escape side.

Electronic powered locks should return to the unlocked position:

(a) on operation of the fire alarm system;
(b) on loss of power or system error;
(c) on activation of a manual door release unit (Type A) to BS En 54 11:2001 positioned at the
door on the escape side. Where the door provides escape in either direction, a unit should be
installed on both sides of the door.
5.12 In non-residential buildings it may also be appropriate to accept on some final exit doors locks for
security that are used only when the building is empty. In these cases the emphasis for the safe use of
these locks must be placed on management procedures.

TABLE 9 EMERGENCY LIGHTING.

Minor changes to provisions.
Purpose group Office, Storage and Other non-residential, Shop and commercial and Car parks emergency
lighting provisions now applies irrespective of whether public are admitted or not

Any
Purpose
group
windowless
w.c.s
under 8m2
now
deleted
from
requiring
emergency
lighting.

20
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Issued 01/01/07 Rev Page 21

Protected Power Circuits.

The potential for damage should be limited by the use of robust cables, selection of cable routes and / or by
protection in areas where cables may be susceptible to damage.
Cable supports should generally be non-combustible and such that circuit integrity will not be reduced below
that afforded by the cable.
Cables should meet PH 3.0 classification when tested in accordance with BS EN 50200; 2006 (incorporating
Appendix E) or an equivalent standard.
Cables should pass only through parts of the building in which the fire risk is negligible and separate from any
circuit provided for another purpose.
In large or complex buildings there may be a need to operate for an extended period during a fire. Further
information is given in BS 5839-1, BS 5266-1 and BS 7346-6

Evacuation Lifts.
Similar provisions with the additional provision, but where a fire fighting lift has been provided to safety
requirement B5, this can be utilised as part of a management plan for evacuating disabled people. Any such
plan should include a contingency for when the Fire and Rescue Service arrive.

Mechanical Ventilation and Air Conditioning Systems.

Completely revised section 5.46 5.53
Mechanical ventilation systems are to be designed so that in a fire the ductwork does not transfer fire and
smoke through the building and prejudice means of escape routes.

Exhaust points should be sited as not to jeopardize the building i.e. sited away from final exits, combustible
claddings or roofing materials and openings into buildings.

Ventilation ducts supplying or extracting air directly to or from a protected escape route should not also
serve other areas. (Separate ventilation system should be provided for each protected stair).

Ductwork serving more than one part of a sub-divided escape routes, a fire damper should be provided
where ductwork enters each section of escape route operated by a smoke detector or suitable fire detection
system. Fire dampers are to close when smoke is detected.

Ducts passing through the protected escape route enclosure should be fire-resisting.
NOTE: Fire dampers activated only by fusible links are not suitable for protected escape routes (ES
classified fire and smoke damper activated by a suitable fire detection system may be used.)

Systems that re-circulates air must have smoke detectors fitted in the extract ductwork before the point of
separation of the re-circulated air and the air to be discharged to open air and before any filters or other air
cleaning equipment. Such detectors should:
a. Immediately shut down the system; and b. Switch the ventilation system from re-circulating mode to
extraction to open air, so as divert any smoke out to outside.

Non-domestic kitchens, carparks and plant rooms are to have separate and independent extraction systems
and the extracted air should not be re-circulated

Guidance of mechanical ventilation in places of assembly refer to BBS5588-6: 1991

Where a pressure differential system is installed, ventilation and air conditioning plant requirements are
given in BS5720: 1979

Guidance on the provision of smoke detectors in ventilation ductwork is given in BS5839-1; 2002. Refer
also to BS 5588: Part 9 Fire precautions - Code of practice for ventilation and air conditioning ductwork.

21
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note
Issued 01/01/07 Rev Page 22

B3 INTERNAL FIRE SPREAD STRUCTURES.

Revised
wording
mentioning
automatic fire
suppression
systems.

SECTION 8 COMPARTMENTATION.
Flats additional requirements
8.14 Blocks of flats with a floor more than 30m above ground level should be fitted with a sprinkler system.
NOTE: Sprinklers to be fitted to flats only and do not have to be fitted to common areas. For the purposes of
this paragraph the limit on the scope of BS 9251: 2005 to buildings below 20m in height can be ignored.

Institutional Buildings including healthcare.

8.16 cross referencing to progressive horizontal evacuation compartmentation in means of escape provisions

TABLE 12 MAXIMUM DIMENSIONS OF BUILDING OR COMPARTMENT (NON-RESIDENTIAL

BUILDINGS) revised table - schools references deleted

22
 Single storey
New Note 4 how to measure
max floor area /
Compartment Height i.e. from
height without
finished floor level to
sprinklers or
underside of roof or ceiling.
compartmentation

Construction of Compartment Walls and Compartment Floors.

8.20 - new Note 2 where services are incorporated within the construction that could provide a potential
source of ignition, care should be taken to ensure the risk of fire developing and spreading prematurely into
adjacent compartments is controlled.

8.28 8.27 new requirement.

At a compartment floors junction with an external wall having no fire resistance (e.g. curtain walling) the
external wall must be restrained at floor level to reduce wall movement away from floor edge when exposed to
fire.

Compartment walls must be able to accommodate the predicted deflection of the floor above by either:
(a) having a suitable head detail between wall and floor, that can deform but maintain the junctions fire
integrity;
(b) wall to be designed to resist additional vertical load from the floor above as it says under fire conditions
and thus maintain integrity.

NOTE: Where compartment walls are located within the middle half of a floor between vertical supports, the
predicted deflection may be assumed to be 40mm unless a smaller value can be justified by
assessment. Outside this area the limit can be reduced linearly to zero at the supports for steel
beams that do not have the required fire resistance, reference should be made to SCI Publication 288
fire safe design A New Approach to Multi-Storey Steel-Framed Buildings.

Junction of Compartment Wall with Roof.

Various changes.

8.29 - Note 1 - Thermoplastic roof lights should not be used in 1500mm compartment wall / roof zone.

8.31 375mm extension of compartment walls above roof coverings can be reduced to 200mm with roof
coverings AA, AB or AC.

23
Dia 30 revised and updated.

24
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 25

Section 9: Concealed Spaces (Cavities).

This has been overhauled with new diagrams added and more text on cavity barriers locations (previously
contained in a table).

New diagram 33 added.

Previous Table 13 has been incorporated into the text of this section as to the location of cavity barriers to
avoid confusion and aid understanding.

25
Re numbered table

9.10 Under floor service voids now require cavity barrier sub-division.

9.13 Window frames and doors frames are now regarded as cavity barriers and if they are constructed of
steel or timber they must comply with the relevant requirements, i.e. timber minimum 38mm thick / steel
0.5mm thick watch the use of upvc windows, a hr cavity closer will be required.

Diagram 34
amended
cavities to be
closed around
full opening,
including cill
(which was
previously not
required).

26
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 27

SECTION 10: PROTECTION OF OPENINGS AND FIRE STOPPING.

Clause 10.11 10.15. Comprehensive guidance now provided on fire dampers requiring.
(a) Fire dampers to be securely fixed.
(b) Provisions to prevent displacement by expansion in a fire of the ductwork to which they are fitted.
(c) Adequate access to be provided for inspection / testing / maintenance.
(d) Dampers to buildings involving a sleeping risk, e.g. hotel or residential care homes are to be actuated
by smoke detector controlled automatic release mechanism, in addition to thermally actuated devices.

Some exceptions if occupants can make their own escape unaided and a L1 fire alarm system is install
throughout are:
(a) If on detection of smoke, the alarm system signals the immediate evacuation of all occupants, then fire /
smoke dampers are not needed; and
(b) If the building is divided into fire compartments and the alarm system is arranged to signal the
immediate evacuation of all occupants of the fire compartment in which the fire has been detected, then
smoke detector operated fire/smoke dampers need only be provided where ductwork enters or leaves
the fire compartment.

NOTE Fire dampers actuated only by fusible links are not suitable for protecting escape routes. However, an
ES classified fire and smoke damper, which is activated by a suitable fire detection system, may be used.

Reference to BS 5720: 1979 on design and installation / BS EN 1366-2 and BS EN 13501-3 as to testing
dampers.

SECTION 11: SPECIAL PROVISIONS FOR CAR PARKS AND SHOPPING

COMPLEXES.
Minor revisions:
11.3 (c) Where one element of structure supports or carries or gives stability to another, the fire resistance
of the supporting element should be N.LT the minimum period of fire resistance for the other
element (whether that other element is loadbearing or not).

(d) If the building is also used for any other purpose, the part forming the car park is a separated part
and the fire resistance of any element of structure that supports or carries or gives stability to
another element in the other part of the building should be NLT the minimum period of fire
resistance for the elements it supports, and

(e) All materials used in the construction of the building, compartment or separated part should be
NON COMBUSTIBLE.

27
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 28

B4 EXTERNAL FIRE SPREAD.

Section 12 Construction of external walls
12.7 Insulation Materials/Products (new requirement)
In a building with a storey more than 18m above ground level any insulation products, filler material (not
including gaskets, sealants and similar), etc., used in the external wall construction should be of limited
combustibility (other than to masonry cavity wall construction which complies with Diagram 34).

12.8 12.9 Cavity Barriers (new notes)

12.8 Cavity barriers should be provided in accordance with Section 9. above
12.9 In the use of an external wall construction of a building which, by virtue of paragraph 9.10d external
cladding system with a masonry or concrete inner leaf, is not subject to the provisions of Table 13
Maximum dimensions of cavities in non-domestic buildings, the surfaces which face into cavities should
also meet the provisions of Diagram 40.

Section 13 Space Separation

13.6 Notional boundaries now need to be determined and assessed between buildings constructed on the
same site, but is to be operated / managed by different organisations.
Previously this only applied to Residential and Assembly and Recreational purpose groupings.

28
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 29

Table 15 Permitted unprotected areas in small buildings or compartments

Minor addition to clarify how this table should be used, i.e. the total percentage of unprotected area is found by
dividing the total unprotected area by the area of a rectangle that encloses all the unprotected areas and
multiplying this result by 100.

29
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 30

Section 17- Access to Building for Fire Fighting Personnel.

Revised Guidance
17.3 Fire fighting shafts now been to be provided to Assembly and Recreational purpose groups in addition
to shops (purpose group 4) and Industrial (Purpose group 6) with storeys over 900m2, where the floor is
more than 7.5m above Fire and Rescue Service vehicle access level.

Number and Location of Fire Fighting Shafts.

Revised text hose distances added.
17.8 Fire fighting shafts should be located to meet maximum hose distance set out below and at least 2
should be provided in buildings with storeys over 900m2, where the floor is more than 18m above Fire
Service vehicle access level (or above 7.5m for purpose groups 4, 5 and 6).

17.9 Buildings with sprinklers fitted throughout sufficient fire fighting shafts to be provided so that every
part of the storey that is more than 18m above Fire Service vehicle access level (or above 7.5m for
Purpose Groups 4, 5 and 6), is N.MT 60m from a fire main outlet in a fire fighting shaft, measure on a
route suitable for laying hoses.
17.10 Buildings without sprinklers every part of every storey over 18m or 7.5m as previous above Fire
Service access level is not more than 45m from a fire main outlet contained in a protected shaft and
60m from fire main outlet in a fire fighting shaft measured along a route suitable for laying hoses.
NOTE: To meet the 45m distance it may be necessary to provide additional fire mains in escape stairs
(these do not all have to be designed as fire fighting shafts).

30
B5 ACCESS FOR FIRE FIGHTING.
Various amendments made.

Design and Construction of Fire Mains.

The outlets from fire mains should be located within the protected enclosure of a stairway or a protected lobby
where one is provided.

Guidance on other aspects of the design and construction of fire mains, not included in the provisions of this
Approved Documents, should be obtained from BS 9990:2006 (new code).

NOTE: Wet fire mains should be provided in buildings with a floor as more than 50m (previously 60m) above
Fire and Rescue Service vehicle access level. In lower buildings where fire mains are provided, either wet or
dry mains are suitable.

Provision of Private Hydrants (new provision 15.7 15.8)

Where a building has a compartment of 280m2 or more and is erected more than 100m from an existing
hydrant, additional hydrants need to be provided.
(a) Buildings provided with fire mains hydrants should be provided within 90m of dry fire main inlets.
(b) Building not provided with fire mains hydrants should be provided within 90m of any entry point to the
building and not more than 90m apart.

Each fire hydrant should be clearly indicated by a plate affixed nearby in a conspicuous position in accordance
with BS 3251:1976.
Where no piped water supply is available or where there is insufficient pressure and flow in the water main, or
an alternative arrangement is proposed, the alternative source of supply should be provided in accordance with
the following recommendations:
(a) A charged static water tank of at least 45,000 litre capacity; or
(b) A spring, river, canal or pond capable of providing or storing at least 45,000 litres of water at all times of
the year, to which access space and a hard standing are available for a pumping appliance; or
(c) Any other means of providing a water supply for fire fighting operations considered appropriate by the
Fire and Rescue Authority.

Vehicle Access.
Provisions similar, other than you are now required for blocks of flats to have fire fighting pump vehicle access
to within 45m of all points within each dwelling (previously it was only to flat entrance doors).

Dia 49 Relationship between building and hardstanding / access roads for high reach appliance and
Table 20 Typical fire and rescue service vehicle access route specification-
Notes added that - not all fire fighting appliances are standardised and you much check with the Building
Control Body and Fire and Rescue Service for relevant dimensions and ground load bearing capacity.
(Establish GMC provisions update information)

16.5 Every elevation to which fire fighting vehicle access is provided should have suitable doors, NLT
750mm wide giving access to the buildings interior.
New requirement Doors should be provided such that there is no more than 60m between each door
and / or the end of that elevation (e.g. a 150m elevation would need at least 2 doors).

31
Variations for Block of Flats.
17.14 Provided compartmentation and design of the flats is in accordance with the Approved Document you
do not have to provide a fire fighting lobby between the fire fighting stair(s) and the protected corridor or lobby
provided for means of escape purposes.

Similarly, the fire fighting lift can open directly into such a protected corridor or lobby, but the fire fighting lift
landing doors are to be N.M.T. 7.5m from the fire fighting stair door.

Dia 52 Components of a Fire Fighting Shaft.

Diagram has been updated and added to.

32
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 33

APPENDIX A.
Table A2 - Minimum periods of fire resistance.
Flats over
Updated and minor changes. 30m require
sprinkler
protection.

Note 4 -
added on
unprotected
steelwork/fire
resistance.

APPENDIX B: Fire Doors.

1. All fire doors should be fitted with a self-closing device except fire doors to cupboards and to service
ducts, which are normally kept locked shut and fire doors within flats (self closing devices are still
necessary on flat entrance doors).
2. All rolling shutters should be capable of being opened and closed manually for fire fighting purposes.
3. Because fire doors often do not provide any significant insulation, there should be some limitation on
the proportion of doorway openings in compartment walls. Therefore, no more than 25% of the length
of a compartment wall should consist of door openings, unless the doors provided both integrity and
insulation to the appropriate level.
NOTE: Where it is practicable to maintain a clear space on both sides of the doorway, then the
above percentage may be greater.
4. Table B1 Provision of fire doors has been amended to include item 9 and 10 and European
standards.

33
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 34

European
standards

34
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 35

New notes
added

35
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 36

APPENDIX E DEFINITIONS.
New definitions added:

EXIT PASSAGEWAY A protected passageway connecting a protected stairway to a final exit (exit
passageways should be protected to the same standard as the stairway they serve).

FIRE DAMPER Mechanical or intumescent device within a duct or ventilation opening which is operated
automatically and designed to prevent the passage of fire and which is capable of achieving an integrity E
classification and/or an ES classification to BS En 13501-3:2005.

FIRE AND SMOKE DAMPER Fire damper which when tested in accordance with BS EN 1366-2:1999 meets
the ES classification requirements defined in EN 13501-3:2005 and achieves the same fire resistance in
relation to integrity, as the element of the building construction through which the duct passes.

GALLERY A floor or balcony, which does not extend across the full extend of a buildings footprint and is
open to the floor below.

LIVE/WORK UNIT A flat, which is intended to serve as a workplace for its occupants and for persons who do
not live on the premises.

PLACES OF SPECIAL FIRE HAZARD Now revised deleting reference to school labs/mat stores as
guidance in Building Bulletin 100 should be used.
Oil filled transformer and switchgear rooms, boiler rooms, storage spaces for fuel or other highly flammable
substances and rooms housing a fixed internal combustion engine.

SCHOOL A place of education for children older than 2 and younger then 19 years. Includes nursery
schools, primary schools and secondary schools as defined in the Education Act 1996.

SHELTERED HOUSING includes:

(a) 2 or more dwellings in the same building;
(b) 2 or more dwellings on adjacent sites where those dwellings are, in each case, designed and
constructed for the purpose of providing residential accommodation for vulnerable or elderly who
receive, or who are to receive, a support service.

STOREY includes:
(a) any gallery in an assembly building (Purpose Group 5); and
(b) any gallery in any other type of building if its area is more than half that of the space into which it
projects; and
NOTE: Where there is M.T one gallery and all the total area of the galleries in any one space is more
than half of the area of the space then the building should be regarded as being a multi storey
building.

36
 Subject APPROVED DOCUMENT B (FIRE 14B
Building Control
SAFETY) VOLUME 2
Guidance Note Buildings other than dwelling houses
(2006 Edition) MAIN CHANGES.
Issued 01/01/07 Rev Page 37

APPENDIX G FIRE SAFETY INFORMATION.

Regulation 16B requires that, where building work involves the erection or extension of a relevant building, or a
relevant change of use of a building, fire safety information shall be given to the responsible person at the
works completion or on first occupation of the building or extension. Building Control do not have to issue a
Completion Certificate if the relevant information has not been provided and the persons responsible
could be subject to enforcement action if they do not provide such information.

fire safety information means information relating to the buildings or extensions design and
construction, and the services, fittings and equipment provided in or in connection with the building or
extension which will assist the responsible person to operate and maintain the building or extension with
reasonable safety;

a relevant building is a building to which the Regulatory Reform (Fire Safety) Order 2005 applies (S.I.
2005/1541, see article 6), or will apply after the completion of building work;

a relevant change of use is a material change of use where, after the change of use takes place, the
Regulatory Reform (Fire Safety) Order 2005 will apply, or continue to apply, to the building; and

responsible person has the meaning given in article 3 of the Regulatory Reform (Fire Safety) Order
2005.

The information below is only intended as a guide as to the type and level of information to be provided, as it
will vary from building to building and should be therefore be considered on a case-by-case basis.

Simple Buildings.
For most buildings basic information on the location of fire protection measures may be all that is necessary.
An as-built plan of the building should be provided showing:
a. escape routes;
b. compartmentation and separation (i.e. location of fire separating elements, including cavity barriers in walk-
in spaces);
c. fire doors, self-closing fire doors and other doors equipped with relevant hardware (e.g. panic locks).
d. locations of fire and/or smoke detector heads, alarm call-points, detection/alarm control boxes, alarm
sounders, fire safety signage, emergency lighting, fire extinguishers, dry or wet risers and other fire fighting
equipment and location of hydrants outside the building;
e. any sprinkler system(s), including isolating valves and control equipment;

f. any smoke-control system(s) (or ventilation system with a smoke-control function), including mode of
operation and control systems;
g. any high-risk areas (e.g. heating machinery);
h. specifications of any fire safety equipment provided, in particular any routine maintenance schedules; and
i. any assumptions in the design of the fire safety arrangements regarding the management of the building.
j. any provision incorporated into the building to facilitate the evacuation of Disabled people. This information
can then be used when designing suitable Personal Emergency Escape Plans.

37
Complex Buildings.
These require a more detailed record of the fire safety strategy and procedures for operating and maintaining
any fire protection measures of the building. Further guidance is available in BS 5588-12:2004 - Fire
precautions in the design, construction and use of buildings: Managing fire safety (Annex A Fire Safety
Manual).

These records should include:

a. The fire safety strategy, including all assumptions in the design of the fire safety systems (such as fire load).
b. Any risk assessments or risk analysis.
c. All assumptions in the design of the fire safety arrangements regarding the management of the building.
d. Escape routes, escape strategy (e.g. simultaneous or phased) and muster points.
e. Details of all passive fire safety measures, including compartmentation (e.g. location of fire separating
elements), cavity barriers, fire doors, self-closing fire doors and other doors equipped with relevant
hardware (e.g. electronic security locks), duct dampers and fire shutters.
f. Fire detector heads, smoke detector heads, alarm call-points, detection/alarm control boxes, alarm
sounders, emergency communications systems, CCTV, fire safety signage, emergency lighting, fire
extinguishers, dry or wet risers and other fire fighting equipment, other interior facilities for the fire and
rescue service, emergency control rooms, location of hydrants outside the building, other exterior facilities
for the fire and rescue service.
g. Details of all active fire safety measures, including.

Sprinkler system(s) design, including isolating valves and control equipment; and

Smoke-control system(s) (or HVAC system with a smoke-control function) design, including mode of
operation and control systems.
h. Any high-risk areas (e.g. heating machinery) and particular hazards.
i. As-built plans of the building showing the locations of the above.

j. Specifications of any fire safety equipment provided, including operation details, operators manuals,
software, system zoning and routine inspection, testing and maintenance schedules. Records of any
acceptance or commissioning tests.
k. Any provision incorporated into the building to facilitate the evacuation of disabled people.

l. Any other details appropriate for the specific building.

38