THERMODYNAMICALLY EFFICIENT DISTILLATION:

NGL FRACTIONATION

D. B. MANLEY
Department of Chemical Engineering, University of Missouri - Rolla
Rolla, Missouri 65409, USA

Keywords: Thermodynamics, Distillation, Ethane, Propane, Separations

Abstract
The problem of separating the liquid components which have been recovered from natural gas is discussed.
Opportunities for improved efficiency using distributed distillation, recycle coupling, heat pumping, and partial effect
distillation are presented. Emphasis is placed upon energy efficiency with potential savings in capital costs as applied to
heat driven processes.

1. Introduction been simplified to include only pentanes, normal hexane, and normal
Significant savings in utilities may be achieved by using heat heptane. The battery limits conditions reflect pipeline or deep well
integrated distillation in innovative configurations. On a percentage storage requirements.
basis, capital savings are somewhat smaller than utility savings; but A conventional process ( for fractionating the feed is shown in
they are not negligible. The improvements are at the expense of figure 1. The deethanizer (DER) operates at about 450 psia and
increased complexity, and incur the risk of new technology.
However, conventional equipment may be used, and only the FIGURE 1
ETHANE
configurations changed. NGL FRACTIONATION
The innovative configurations may be generated by observing CONVENTIONAL PROCESS
thermodynamic inefficiencies in conventional process designs. FEED
DER
These are typically apparent in relationships between the primary ISO-
PROPANE BUTANE
process variables such as temperature, pressure, and composition.
The relationships may be observed through conventional analysis
such as McCabe - Thiele diagrams, composite heating and cooling DPR DIBR
curves, and temperature - composition plots.
Because of the multiple products produced by the fractionation
of natural gas liquids and because of the large amount of energy
required, NGL fractionation provides several opportunities for DBR
NORMAL
economical process improvements through improved thermodynamic BUTANE
efficiency.
GASOLINE
2. Conventional NGL Fractionation
Table 1 shows the feeds and products normally encountered in separates ethane from the propane and heavier components. Because
the NGL fractionation process. The feed is a raw mix which is the critical temperature of ethane is about 90oF, the condenser of the
gathered from several upstream demethanizing gas plants and is deethanizer must be refrigerated. The depropanizer (DPR) operates
transported via pipeline as a liquid under pressure. Some minor at about 250 psia and separates propane from the butanes and heavier
components, such as neopentane, sulphur compounds, and water, components. The debutanizer (DBR) operates at about 70 psia and
have been omitted; and the gasoline fraction characterization has separates the butanes from the gasoline. The deisobutanizer (DIBR)
operates at about 85 psia and separates isobutane from normal
Table 1 butane. This separation is positioned at the end of the process
Specifications for NGL Fractionation
because isobutane and normal butane have similar boiling points and
Liq Vol % Feed Ethane Propane Isobutane N-butaneGasoline require a large number of stages and a high reflux ration to separate.
A conventional NGL fractionation process requires about 73
Methane 0.5 1.36
Ethane 37.0 95.14 7.32 MBtu/Bbl of hot utility to reboil the distillation columns.
Propane 26.0 3.50 90.18 2.00
Isobutane 7.2 96.00 4.50 3. Recycle Coupled Deethanizer and Depropanizer
N-butane 14.8 2.00 95.00 Figure 2 shows a McCabe-Thiele diagram for the conventional
Butanes 2.50 3.00 depropanizer in figure 1. The column is well designed for the feed
Isopentane 5.0 33.13 of about 48 mole percent propane and lighter components, and the
Pentanes 3.5 0.50 23.52
diagram shows little opportunity for improvement. However, the
N-pentane
N-hexane 4.0 26.90 temperature - composition diagram, shown in figure 3 for the
N-heptane 2.0 13.45 conventional deethanizer in figure 1, shows that propane is
remixed with the normal butane and heavier components near the
Deg. F 85 90 100 100 100 100 bottom of the column at temperatures above about 190oF. The
Psig 600 1600 1000 1000 1000 1000 remixed propane must then be again separated in the downstream
depropanizer column. The remixing occurs because butanes are

Page 1 of 6
 FIGURE 2
MCCABE THIELE DIAGRAM FIGURE 4
CONVENTIONAL DEPROPANIZER RECYCLE COUPLED DEETHANIZER AND
1.0 DEPROPANIZER
VAPOR MOLE FRACTION PROPANE AND LIGHTER

0.9
ETHANE
0.8

0.7
FEED DER PROPANE
0.6

0.5

0.4 DPR

0.3

0.2
BUTANES
AND
0.1 HEAVIER

0.0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 lower the pressure of the deethanizer to slightly below the
LIQUID MOLE FRACTION PROPANE AND LIGHTER depropanizer pressure of about 250 psia. Figure 5 shows the
temperature - composition profile for the low pressure, recycle
drawn up the column when propane is reboiled to drive off ethane. coupled deethanizer which eliminates the remixing shown in
These butanes must then be refluxed down the column along with the figure 3. Because of the lower pressure, the temperatures in figure
propane. 5 are somewhat lower than those in figure 3.
This unnecessary mixing and separation may be avoided by Figure 6 gives a McCabe - Thiele diagram for the recycle
using a recycle coupled deethanizer and depropanizer (Manley, coupled depropanizer in the figure 4 process with a feed
1996) as shown in figure 4. In the figure 4 process the deethanizer considerably richer in propane in comparison with the conventional
is reboiled by recycling a vapor sidedraw from the downstream process shown in figure 2. As a result the reflux ratio for the recycle
depropanizer. The remixing occurring in the conventional process coupled depropanizer is significantly reduced with commensurate
is then shifted into the depropanizer where it properly belongs. In
order to avoid compression of the recycled vapor it is necessary to FIGURE 5
TEMPERATURE / COMPOSITION DIAGRAM
FIGURE 3 RECYCLE COUPLED DEETHANIZER
TEMPERATURE / COMPOSITION DIAGRAM
0.9
CONVENTIONAL DEETHANIZER
1.0 ETHANE
LIQUID COMPOSITION, MOLE FRACTION

0.8
0.9
ETHANE
LIQUID COMPOSITION, MOLE FRACTION

0.7
0.8
PROPANE
0.6
0.7

0.6 0.5
PROPANE
0.5 0.4
0.4
0.3
0.3
N-BUTANE 0.2
0.2 N-BUTANE
0.1
0.1
ISOBUTANE
ISOBUTANE 0.0
0.0
40 60 80 100 120 140 160 180 200 220 240
0 20 40 60 80 100 120 140 160
STAGE TEMPERATURE, DEGREES FAHRENHEIT STAGE TEMPERATURE, DEGREES FAHRENHEIT

Page 2 of 6
 FIGURE 6 FIGURE 7
MCCABE THIELE DIAGRAM
RECYCLE COUPLED DEPROPANIZER
RECYCLE COUPLED DEETHANIZER SIDE STRIPPER
1.0 ETHANE
VAPOR MOLE FRACTION PROPANE AND LIGHTER

0.9

0.8

0.7
FEED DER DESS
0.6

0.5 PROPANE

0.4

0.3 DPR

0.2

0.1 BUTANES
AND
0.0 HEAVIER
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
LIQUID MOLE FRACTION PROPANE AND LIGHTER
depropanizer pressure of about 250 psia. As may be seen by a
comparison of figures 3 and 5, the deethanizer condenser
savings in reboiler hot utility. The savings are a direct consequence temperature of about 15oF in the recycle coupled process is
of the improved thermodynamic efficiency due to the elimination of considerably lower than the condenser temperature of about 55oF in
remixing in the deethanizer and do not depend upon its pressure. the conventional process. This lower condenser temperature requires
lower temperature refrigeration and will incur precipitation of
4. Deethanizer Side Stripper hydrates if the process gases are not sufficiently dried.
As shown in figure 5, propane is also separated from the Figure 8 shows how the deethanizer condenser refrigeration
butanes in the rectification section of the deethanizer between about system may be replaced with a thermomechanically integrated
75oF and 50oF. However, the propane is then refluxed back down the process which also keeps the process temperatures high enough to
column into the butanes so that it may be produced in the bottoms preclude formation of hydrates. In the figure 8 process, the overhead
product. The propane and butanes must then be reseparated in the vapors from the butanes rejection portion of the deethanizer and
downstream depropanizer - whether or not its recycle coupled with
the deethanizer. FIGURE 8
Figure 7 shows how a deethanizer side stripper (DESS) may be THERMOMECHANICALLY INTEGRATED DEETHANIZER
used to eliminate unnecessary remixing of propane with butanes in
the deethanizer rectification section. In the figure 7 process CW
sufficient propane is refluxed past the side stripper feed tray and ETHANE
down the deethanizer to remove butanes from the side stripper feed,
so that the side stripper bottoms meets propane product
specifications. The remaining propane with dissolved ethane is fed
to the side stripper so that the ethane may be removed. Since the side
stripper bottoms meets propane product specifications and is at
CW
essentially the same pressure as the depropanizer, the side stripper
may be reboiled using a propane vapor product from the
depropanizer overhead. This eliminates the need for a separate side
stripper reboiler, saves energy, and reduces the size of the
depropanizer condenser. At least 25% of the propane in the feed may
be recovered through the deethanizer side stripper without passing
through the depropanizer.
A deethanizer side stripper may be used with or without a
recycle coupled depropanizer, but the most thermodynamically DESS
efficient configuration is to use both simultaneously. FEED DER

5. Thermomechanically Integrated Deethanizer

In order to be recycle coupled with the depropanizer, the TO / FROM
deethanizer in the figure 7 process must be operated at the DEPROPANIZER

Page 3 of 6
the overhead vapors from the deethanizer side stripper are combined would eliminate the remixing in the depropanizer stripping section.
and compressed in two stages before feeding a high pressure However, the debutanizer pressure would have to be raised to about
deethanizer rectification section. The liquid refluxed from the high 250 psia, or the depropanizer pressure would have to be lowered to
pressure rectification section is then flashed and partially vaporized about 70 psia, or a compressor would have to be used to compress
to provide refrigeration for the overhead condenser. The partially the recycle vapors from the debutanizer to the depropanizer. None
vaporized reflux is then separated, the vapor recompressed, and the of these alternatives is economically viable so this possibility is not
liquid used as reflux for the deethanizer and side stripper. The recommended. A high pressure debutanizer would be too expensive
recompressed vapor is partially condensed with cooling water to and would require a much higher temperature hot utility, a low
reject the heat absorbed in the condenser and is fed to the bottom of pressure depropanizer would require refrigeration and couldnt be
the high pressure rectification sections. In addition to keeping the recycle coupled with the deethanizer, and an additional compressor
process temperatures above about 50oF, the thermodynamically would be too expensive to purchase and operate.
integrated refrigeration process in figure 8 is highly efficient and A depropanizer side stripper (DPSS) to recover gasoline free
requires minimal power to operate in comparison with a conventional butanes from the depropanizer rectifying section is sometimes
refrigeration process. worthwhile and is shown in figure 10. The side stripper bottoms
In addition to being more thermodynamically efficient when product contains isobutane and normal butane, and their composition
combined with recycle coupling, side stripper, and thermomechanical
integration; a low pressure deethanizer has the additional cost FIGURE 10
advantage of being smaller in diameter and wall thickness in DEPROPANIZER SIDE STRIPPER
comparison with a conventional, high pressure deethanizer. CW
PROPANE
6. Depropanizer Side Stripper
Considering the temperature - composition diagram for a
conventional depropanizer shown in figure 9, it is apparent that the
same strategies used in the deethanizer improvements may be DEETHANIZED
DPR DPSS
applicable. Above about 230oF butanes and gasoline are remixed as FEED CW
pentanes are reboiled up the column along with the propane and ISO-
butanes. These pentanes must then be refluxed back down the BUTANE
column. And between about 155oF and 175oF butanes are remixed CW DIBR
with pentanes as theyre rejected from the propane product in the
condenser.
Recycle coupling with the downstream debutanizer in figure 1
DBR
NORMAL
BUTANE
FIGURE 9
TEMPERATURE / COMPOSITION DIAGRAM
CONVENTIONAL DEPROPANIZER GASOLINE
1.0
PROPANE is somewhat enriched in isobutane in comparison with the
0.9 depropanizer bottoms product. Consequently, it is advantageously
LIQUID COMPOSITION, MOLE FRACTION

fed to a different location in the downstream deisobutanizer from the

0.8 feed location of the debutanizer overhead, and the deisobutanizer
reflux ratio is reduced in comparison with a conventional unit.
0.7 The depropanizer side stripper therefore improves the process
thermodynamic efficiency in two ways. Since at least 25% of the
butanes bypass the debutanizer, its size and duties are considerably
0.6
smaller. And, because the butanes are partially separated in the side
N-BUTANE stripped depropanizer, the deisobutanizer size and duties are
0.5 reduced. However, the side stripped depropanizer requires a few
more stages to efficiently reject gasoline from the side stripper; and,
0.4 of course, the side stripper itself adds complexity to the process. As
ISOBUTANE the capacity of the overall process increases, the economic benefit of
0.3 the added efficiency becomes more significant in spite of the
increased complexity.
0.2
7. Normal Butane Distributor
The temperature - composition diagram for a conventional
0.1 ISOPENTANE debutanizer, shown in figure 11, shows that isobutane and normal
N-PENTANE butane are remixed in both the stripping section between about
0.0 150oF and 205oF and in the rectifying section between about 110oF
100 120 140 160 180 200 220 240 260 and 100oF. This is thermodynamically inefficient since these two
STAGE TEMPERATURE, DEGREES FAHRENHEIT components must be separated in the downstream deisobutanizer as

Page 4 of 6
 FIGURE 11
TEMPERATURE / COMPOSITION DIAGRAM FIGURE 13
CONVENTIONAL DEBUTANIZER PARTITIONED COLUMN (PETLYUK)
0.8
DEBUTANIZER AND DEISOBUTANIZER
LIQUID COMPOSITION, MOLE FRACTION

N-BUTANE

0.6 ISO-
BUTANE
ISOPENTANE
D
I
0.4
B
N-PENTANE N R
ISOBUTANE DEPROPANIZED NORMAL
B
FEED BUTANE
0.2 D
N-HEXANE
D
B
R
0.0
100 120 140 160 180 200
STAGE TEMPERATURE, DEGREES FAHRENHEIT

GASOLINE
shown in figure 1. The process may be improved by using a recycle
coupled normal butane distributor (NBD) column to separate
isobutane from gasoline while distributing the normal butane between 8. Partial Effect Deisobutanizer
the overhead and bottoms products as shown in figure 12. The The debutanizer in the figure 12 process operates closer to
process in figure 12 is the well documented Petlyuk configuration minimum reflux and thus requires more stages than the debutanizing
(Petlyuk et. al., 1965) except that a reboiler is used on the portion of the figure 13 process. This allows some of the reboiler
deisobutanizer column to improve heat integration. The energy to be moved to the much lower temperature deisobutanizer
thermodynamic efficiency is improved in comparison with a reboiler and reduces overall process energy consumption. However,
conventional debutanizer and deisobutanizer by eliminating remixing the additional stages make it difficult to accommodate in a single
of isobutane and normal butane in the debutanizer and by allowing partitioned column with a uniform diameter. In other words, because
the debutanizer to directly provide at least part of the reboil vapor of the relatively high reflux ratio in the deisobutanizer, its diameter
is much larger than the debutanizer designed for the most economical
FIGURE 12 approach to minimum reflux. A partial effect deisobutanizer system,
NORMAL BUTANE DISTRIBUTOR COLUMN
as shown in figure 14, provides one solution to this problem.
In the figure 14 process the overhead product from the partial
ISO-
ISOBUTANE effect deisobutanizer (PEDIBR) is only partially enriched in
BUTANE
N-BUTANE
DIBR FIGURE 14
PARTIAL EFFECT DEISOBUTANIZER SYSTEM
NORMAL
BUTANE ISO-
DEPROPANIZED FROM
NBD BUTANE
FEED DEPROPANIZER
SIDE STRIPPER LPDIBR

DBR
N-BUTANE NORMAL
GASOLINE BUTANE
ISOBUTANE
GASOLINE N-BUTANE
PEDIBR
required to drive the deisobutanizer.

Figure 13 shows how a partitioned column may be used

simplify the mechanical design for the Petlyuk configuration (Lestak DEPROPANIZED NORMAL
NBD
FEED BUTANE
and Collins, 1997) when the deisobutanizer reboiler is not used and
all the hot utility is used in the debutanizer reboiler. A large column
is vertically partitioned into three sections corresponding the to
normal butane distributor, debutanizer, and deisobutanizer in figure DBR
12. This mechanical combination reduces installation costs N-BUTANE
significantly since fewer pieces of equipment are required. GASOLINE
GASOLINE
Page 5 of 6
isobutane. Consequently, the number of stages and reflux ratio in the The depropanizer bottoms feeds a lower pressure normal
partial effect deisobutanizer are considerably less than in a butane distributor (NBD) section which is mechanically integrated
conventional deisobutanizer, and the partial effect deisobutanizer with the debutanizer (DBR) and partial effect deisobutanizer
may be optimally reboiled using a vapor overhead stream from the (PEDIBR) in a vertically partitioned column. This column operates
debutanizer. This makes the process ideally suited for the partitioned at a sufficiently high pressure so that heat from its condenser may be
column configuration of figure 13. However, the partial effect used to reboil the downstream low pressure deisobutanizer
deisobutanizer overhead must be further fractionated in an additional (LPDIBR) column.
downstream deisobutanizer (LPDIBR). If the downstream The low pressure deisobutanizer is fed by butanes mixtures
deisobutanizer is operated at a lower pressure than the partial effect from the depropanizer side stripper bottom and partial effect
deisobutanizer, then the reboiler of the low pressure deisobutantizer deisobutanizer overhead. The low pressure deisobutanizer operates
may be driven with heat from the condenser of the partial effect at a pressure such that cooling water may be used in its condenser.
deisobutanizer. The energy from the debutanizer reboiler is then
used three times as it cascades through the debutanizer, partial effect 10. Summary
deisobutanizer, and low pressure deisobutanizer, and the overall Table 2 compares several size parameters for the conventional
process is very efficient thermodynamically. And, because the NGL fractionation process shown in figure 1 and the optimum NGL
normal butane distributor column eliminates the remixing occurring fractionation process shown in figure 15. Because of the improved
in the conventional debutanizer, the efficiency is enhanced even thermodynamic efficiency, the hot utility consumed in the reboilers
more. is reduced by 66%. Not shown, but commensurate with this by
energy balance, is a corresponding reduction in cooling water
9. Economically Optimal Process consumption. Some additional power is required for the distributed
The thermodynamic improvements discussed above and process because of the low pressure deethanizer. However, the cost
innovative mechanical designs incorporating partitioned columns associated with this is largely mitigated by a large reduction in the
may be combined as shown in figure 15 to produce an overall wall thickness and consequent cost of the low pressure deethanizer.
configuration which minimizes both capital and operating costs. Because remixing and reseparation are largely omitted in the
In the figure 15 process the low pressure deethanizer (DER) is distributed process, total heat exchange is reduced by 41% with a
partitioned to include the deethanizer side stripper (DESS) within the corresponding reduction in capital costs. The column volumn
increases slightly; but, because of the mechanical partitioning, the
FIGURE 15
ECONOMICALLY OPTIMAL PROCESS FOR NGL FRACTIONATION TABLE 2
SIZE COMPARISONS FOR 100MBPD CONVENTIONAL AND
ETHANE
DISTRIBUTED NGL FRACTIONATION PROCESSES
PROPANE
ISOBUTANE
T
M PARAMETER UNITS CONV. DIST. RATIO
I P
R E
HOT UTILITY MMBTU/HR 305.2 134.4 44%
D
I
POWER HORSEPOWER 6,825 9,395 138%
L
B HEAT EXCHANGE MMBTU/HR 666.8 396.2 59%
D D P
D D N R COLUMN VOLUME CUBIC FEET 53,995 63,343 117%
E P D
E P B SPEC. HOT UTILITY MBTU/BBL 73.2 32.3 44%
S S I
R R D
S S B
FEED D R
B number of columns remains the same.
R A more detailed comparison of the capital and operating costs
for the conventional and distributed NGL fractionation processes is
not available, but a moderate reduction in capital cost and a large
reduction in operating cost are typical for processes incorporating the
NORMAL improvements in thermodynamic efficiency proposed.
GASOLINE BUTANE

References
column shell, and the high pressure thermomechanically integrated Katz, D. L., Cornell, D., Kobayashi, R., Poettmann, F. H., Vary, J.
rectification section (TMIR) of the deethanizer is stacked vertically A., Elenbaas, J. R. and Weinaug, C. F., Handbook of Natural
on top of the low pressure section. The refrigeration compressor is Gas Engineering, McGraw-Hill, New York (1959).
thermomechanically integrated with the dual pressure column to Lestak, F. and C Collins, Advanced Distillation Saves Energy and
avoid using separate compressors and to improve energy efficiency. Capital, Chemical Engineering, Pages 72-76, July (1997).
An interreboiler is shown on the deethanizer stripping section to Manley, D. B., Distillation of Natural Gas Liquids, Proceedings of
recover low level heat from the hot normal butane and gasoline the 75th Annual convention, Gas Processors Association, pg.
products. 67-74, March 11-13 (1996).
The deethanizer and deethanizer side stripper in figure 15 are Petlyuk, F. B., Platonov, V. M. and Slavinskii, D. M.,
recycle coupled with the downstream depropanizer (DPR) which is Thermodynamically Optimal Method for Separating
also partitioned to include the depropanizer side stripper (DPSS) Multicomponent Mixtures, International Chemical
within the column shell. An interreboiler is shown on the Engineering, Vol. 5, Number 3, Pages 555-561, July (1965).
depropanizer stripping section to recover intermediate level heat from
the hot gasoline product.

Page 6 of 6