Scribd
Upload
57 views5 pages

Pread Ootings: Emo To Esigners Arch

The memo provides guidance to structural and geotechnical designers on the design process and communication for spread footings. It defines key terms like contact surface, effective footing width and length, bearing stresses, and resistance factors. The design process involves checking bearing stress and eccentricity limits at various limit states and checking sliding failure. Geotechnical designers provide parameters like permissible stress and resistance as functions of footing geometry. Structural designers must share footing location, geometry and load data with geotechnical designers through design data sheets.

Uploaded by

saraviad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
57 views5 pages

Pread Ootings: Emo To Esigners Arch

The memo provides guidance to structural and geotechnical designers on the design process and communication for spread footings. It defines key terms like contact surface, effective footing width and length, bearing stresses, and resistance factors. The design process involves checking bearing stress and eccentricity limits at various limit states and checking sliding failure. Geotechnical designers provide parameters like permissible stress and resistance as functions of footing geometry. Structural designers must share footing location, geometry and load data with geotechnical designers through design data sheets.

Uploaded by

saraviad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Memo to Designers March 2014

4-1

Spread Footings
Introduction
The scope of this Memo is to clarify the terms and design methodology used in the Load
and Resistance Factor Design (LRFD) of spread footings as specified in AASHTO LRFD
Bridge Design Specifications with California Amendments (LRFD-BDS), and to improve
communication between Structure Designer (SD) and Geotechnical Designer (GD).

Definitions and Notation


Contact Surface refers to the bottom surface of the footing located at a specified elevation,
and resultant structural forces and moments are calculated at that level. Refer to Figure 1
for footing local coordinates and illustration of the following parameters used throughout
this Memo:
B = Footing Width. This is the short plan dimension of the footing.
L = Footing Length. This is the long plan dimension of the footing.
M = Factored Bending Moment
MX and MY are calculated at the contact surface in the local X and Y directions,
respectively.
Local X axis is defined to be parallel to the long plan dimension of the footing (L).
V = Factored Shear Force:
VX and VY are calculated at the contact surface in the local X and Y directions, respectively.
B' = Effective Footing Width:
Reduced footing width for an eccentrically loaded footing is calculated as the smaller
of : (B - 2eY) and (L - 2eX ) , where eY and eX are the eccentricities (always positive)
corresponding to MX and MY , respectively.
L' = Effective Footing Length:
Reduced footing length for an eccentrically loaded footing is calculated as the larger
of (B - 2eY) and (L - 2eX ).
A' = B' x L' . Effective Footing Area.

4-1

Spread Footings

Memo to Designers March 2014

PTotal = Total factored axial force


Total factored axial force is calculated at the contact surface as gross (for Strength,
Construction and Extreme Event load combinations) or net (for Service load
combinations).
PPerm = Permanent net axial force
Permanent net axial force is calculated for LRFD permanent loads acting at the
contact surface and is used to evaluate settlement under Service-I limit state load
combination.
Y

+M

B
2

+Y

+P

+M
X

+V

L
2

Figure 1 Components of Moment and Shear in Local Coordinates of the Spread Footing
qg,u = Gross Uniform Bearing Stress
Used for footings on soil, gross uniform bearing stress is the equivalent uniform
vertical stress determined by applying the vertical factored load over the effective
footing area. When determining the gross uniform bearing stress, the designer must
include the weight of the footing and all overburden soil from the top of the footing
to finished grade with applicable load factors.

4-1

Spread Footings

Memo to Designers March 2014

qg,max = Gross Maximum Bearing Stress


Gross maximum bearing stress is the maximum applied vertical stress at the contact
surface when applying factored loads. The gross maximum bearing stress must
include the weight of the footing and of all overburden soil from the top of the footing
to finished grade with applicable load factors. Used for footings on rock, qg,max is based
on triangular or trapezoidal stress distribution, as appropriate, on the footing area.
qn,u = Net Uniform Bearing Stress
Net uniform bearing stress is the gross uniform bearing stress for footings on soil (qg,u)
minus the overburden or vertical effective stress at the contact surface calculated based
on grade elevation at the time of excavation for the footing. The net uniform bearing
stress due to LRFD Service-I load combination is used to evaluate footing settlement
on soil. The net uniform bearing stress is calculated for total factored axial forces.
qn,max = Net Maximum Bearing Stress
Net maximum bearing stress is the gross maximum bearing stress for footings on
rock (qg.max), minus the overburden or vertical effective stress at the contact surface
calculated based on finished grade for abutments and original grade for bents. The
net maximum bearing stress due to LRFD Service-I load combination is used to
evaluate footing settlement on rock. The net maximum bearing stress is calculated
for total factored axial forces.
qn = Gross Nominal Bearing Resistance
Used in Strength and Extreme Event Limit States, this is the gross uniform bearing
stress for footings on soil, or the gross maximum bearing stress for footings on rock
that will fail the soil or rock, respectively, in shear based on a strength criterion.
qR = Factored Gross Nominal Bearing Resistance
Used in Strength and Extreme Event Limit States, qR = b qn where b is resistance
factor from Section 10.5 of the LRFD BDS.
qpn = Permissible Net Contact Stress
This is the net bearing stress resulting in an estimated settlement that is structurally
safe and without adverse impact on serviceability. This value is calculated using total
Service-I loads, irrespective of whether or not consolidation contributes to the total
settlement.

Design Process
The shallow foundation structural design process includes the following steps:

4-1

Spread Footings

Memo to Designers March 2014

1. Contact Bearing Stress Check (Sizing the footing)


Spread footings used to support abutments or bent columns or piers must satisfy the following
requirements:
For Service Limit State (Settlement):
1. qn,u qpn
for footings on soil
2. qn,max qpn
for footings on rock
For Strength, Construction and Extreme Event Limit States:
1. qg,u qR
for footings on soil
2. qg,max qR
for footings on rock

2. Eccentricity Limits
All footings must be checked for tilting/rotation by SD. On competent foundation materials,
the tilting/rotation is considered within acceptable limits, when the maximum eccentricity
calculated based on gross axial force under Service-I Limit State load combination is limited
to B/6 and L/6 for footings on soil, or to B/4 and L/4 for footings on rock. Refer to LRFD
BDS 10.6.4.2 for eccentricity limits under Extreme Event Limit State load combinations.
When founded on poor or soft soils, a detailed tilting/rotation deformation analysis by GD
is required in lieu of this check. SD and GD must communicate especially if non-standard
or special design conditions exist.

3. Sliding Failure
For foundation material at the contact surface the internal friction angle of drained soil
(f) for footings founded on rock or cohesionless soil, and the undrained shear strength for
footings founded on cohesive soil will be provided by the GD. SD will check sliding failure
for Strength and Extreme Event Limit States load combinations per LRFD BDS 10.6.3.4
requirements.
Structural design of the footing shall start after finalizing the size of the footing. The SD
will determine the required depth of the footing and also the amount and distribution of
steel reinforcement.

Communication with Geotechnical Designer


Sizing a spread footing is an iterative process because the calculated Permissible Net Contact

4-1

Spread Footings

Memo to Designers March 2014

Stress (qpn) and the Factored Gross Nominal Bearing Resistance (qR) depend on the location,
dimensions and depth of the footing. To facilitate design, GD will provide these parameters
as a function of the effective footing width, (B'), for a range of effective footing length to
effective footing width ratios, (L'/B'), and a given footing embedment depth specified by
Structural Designer.
If the support location or footing embedment depth changes during the design process, GD
shall be contacted so that the geotechnical design data can be revised.
To prepare foundation recommendations and reports, GD needs foundation location,
geometry, and load data from SD. Attachment No. 1 shows examples of Foundation Design
Data Sheets to be included in the request for Preliminary Foundation Report (PFR) .
Attachment No. 2 (Foundation Geotechnical Data Tables) indicates the format that will be
used for the transmittal of geotechnical foundation design data from GD. The communication
of this data is an intermediate step in the design process. This table will not be included in
the Foundation Report.
Attachment No. 3 (Bridge Foundation Loads) is an example of the detailed load data which
must be provided by SD. If requested, the GD must receive the data shown in Attachment
No.3 prior to the completion of the Foundation Report (FR). Attachment No. 4 shows the
Foundation Design Data Sheet to be included in the request for Foundation Report.

Spread Footing Data Table


Spread Footing Data Tables shall be included in the FR and on the Contract Plans in the
formats shown in Attachment No. 5.
Although Spread Footing Data Table is not necessary for contract administration purposes, its
inclusion is a useful addition to the plans. With the foundation design parameters included
in the table, the engineer can perform an informed inspection of the bearing material. These
design parameters are also a starting point for the future design of widening and emergency
projects.
Original
signed by Barton J. Newton
_________________________________
Barton J. Newton
State Bridge Engineer
Deputy Division Chief, Structure Policy & Innovation
Division of Engineering Services

4-1

Spread Footings

You might also like