International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 03 | June-2015

p-ISSN: 2395-0072

www.irjet.net

Home Automation Using Internet of Things

Vinay sagar K N1,Kusuma S M2
1
2

Student IV SEM, M.Tech, Digital Communication. Engg., MSRIT, Bangalore, India

Assistant Professor, Department of telecommunication, MSRIT, Bangalore, India

---------------------------------------------------------------------***---------------------------------------------------------------------

Abstract- with advancement of Automation technology,

life is getting simpler and easier in all aspects. In todays
world Automatic systems are being preferred over
manual system. With the rapid increase in the number of
users of internet over the past decade has made Internet a
part and parcel of life, and IoT is the latest and emerging
internet technology. Internet of things is a growing
network of everyday object-from industrial machine to
consumer goods that can share information and complete
tasks while you are busy with other activities. Wireless
Home Automation system(WHAS) using IoT is a system
that uses computers or mobile devices to control basic
home functions and features automatically through
internet from anywhere around the world, an automated
home is sometimes called a smart home. It is meant to
save the electric power and human energy. The home
automation system differs from other system by allowing
the user to operate the system from anywhere around the
world through internet connection.
In this paper we present a Home Automation system(HAS)
using Intel Galileo that employs the integration of cloud
networking, wireless communication, to provide the user
with remote control of various lights, fans, and appliances
within their home and storing the data in the cloud. The
system will automatically change on the basis of sensors
data. This system is designed to be low cost and
expandable allowing a variety of devices to be controlled.

Key Words: Home automation System (HAS), Internet of

Things (IoT), Cloud networking, Wi-Fi network, Intel
Galileo Microcontroller
I. INTRODUCTION
A. Overview
Homes of the 21st century will become more and more selfcontrolled and automated due to the comfort it provides,
especially when employed in a private home. A home
automation system is a means that allow users to control
electric appliances of varying kind.
Many existing, well-established home automation systems
are based on wired communication. This does not pose a
problem until the system is planned well in advance and
installed during the physical construction of the building. But
2015, IRJET.NET- All Rights Reserved

for already existing buildings the implementation cost goes

very high.
In contrast, Wireless systems can be of great help for
automation systems. With the advancement of wireless
technologies such as Wi-Fi, cloud networks in the recent
past, wireless systems are used every day and everywhere.

B. Advantages of Home automation systems

In recent years, wireless systems like Wi-Fi have become
more and more common in home networking. Also in home
and building automation systems, the use of wireless
technologies gives several advantages that could not be
achieved using a wired network only.
1) Reduced installation costs: First and foremost, installation
costs are significantly reduced since no cabling is necessary.
Wired solutions require cabling, where material as well as
the professional laying of cables (e.g. into walls) is expensive.
2) System scalability and easy extension: Deploying a
wireless network is especially advantageous when, due to
new or changed requirements, extension of the network is
necessary. In contrast to wired installations, in which cabling
extension is tedious. This makes wireless installations a
seminal investment.
3) Aesthetical benefits: Apart from covering a larger area,
this attribute helps to full aesthetical requirements as well.
Examples include representative buildings with all-glass
architecture and historical buildings where design or
conservatory reasons do not allow laying of cables.
4) Integration of mobile devices: With wireless networks,
associating mobile devices such as PDAs and Smartphones
with the automation system becomes possible everywhere
and at any time, as a device's exact physical location is no
longer crucial for a connection (as long as the device is in
reach of the network).
For all these reasons, wireless technology is not only an
attractive choice in renovation and refurbishment, but also
for new installations.

II. RELATED WORK

[1] Sirsath N. S, Dhole P. S, Mohire N. P, Naik S. C &
Ratnaparkhi N.S
This paper proposes a Home Automation system that
employs the integration of multi-touch mobile devices, cloud
networking, wireless communication, and power-line
communication to provide the user with remote control of
various lights and appliances within their home. This system
uses a consolidation of a mobile phone application, handheld
wireless remote, and PC based program to provide a means
of user interface to the consumer.
Page 1965

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 03 | June-2015

p-ISSN: 2395-0072

www.irjet.net

[2] Basil Hamed

The main objective of this Paper is to design and implement
a control and monitor system for smart house. Smart house
system consists of many systems that controlled by LabVIEW
software as the main controlling system in this paper. Also,
the smart house system was supported by remote control
system as a sub controlling system. The system also is
connected to the internet to monitor and control the house
equipments from anywhere in the world using LabVIEW.
[3] Deepali Javale, Mohd. Mohsin, Shreerang Nandanwar
The prime objective of this paper is to assist
handicapped/old aged people. It gives basic idea of how to
control various home appliances and provide a security
using Android phone/tab. The design consists of Android
phone with home automation application, Arduino Mega
ADK. User can interact with the android phone and send
control signal to the Arduino ADK which in turn will control
other embedded devices/sensors.
[4] Basma M. Mohammad El-Basioni, Sherine M. Abd Elkader and Mahmoud Abdelmonim Fakhreldin
This paper proposes a new design for the smart home using
the wireless sensor network and the biometric technologies.
The proposed system employs the biometric in the
authentication for home entrance which enhances home
security as well as easiness of home entering process. The
structure of the system is described and the incorporated
communications are analyzed, also an estimation for the
whole system cost is given which is something lacking in a
lot of other smart home designs offers.WB-SH is designed to
be capable of incorporating in a building automation system
and it can be applied to offices, clinics, and other places. The
paper ends with an imagination for the future of the smart
home when employs the biometric technology in a larger
and more comprehensive form. The paper ends with an
imagination for the future of the smart home when employs
the biometric technology in a larger and more
comprehensive form.

III. SYSTEM ANALYSIS

A. Problem Definition
Home automation systems face four main challenges, these
are high cost of ownership, inflexibility, poor manageability,
and difficulty in achieving security. The main objectives of
this research is to design and implement a home automation
system using IoT that is capable of controlling and
automating most of the house appliances through an easy
manageable web interface. The proposed system has a great
flexibility by using Wi-Fi technology to interconnect its
distributed sensors to home automation server. This will
decrease the deployment cost and will increase the ability of
upgrading, and system reconfiguration.

B. Proposed System Feature

The proposed system is a distributed home automation
system, consists of server, sensors. Server controls and
monitors the various sensors, and can be easily configured to
handle more hardware interface module (sensors). The Intel
Galileo development board, with built in WiFi card port to
2015, IRJET.NET- All Rights Reserved

which the card is inserted, acts as web server. Automation

System can be accessed from the web browser of any local
PC in the same LAN using server IP, or remotely from any PC
or mobile handheld device connected to the internet with
appropriate web browser through server real IP (internet
IP). WiFi technology is selected to be the network
infrastructure that connects server and the sensors. WiFi is
chosen to improve system security (by using secure WiFi
connection), and to increase system mobility and scalability.

IV. SYSTEM DESIGN AND IMPLEMENTATION

A. Proposed Home Automation System

Figure 1: Proposed model of Home automation

system
The proposed model of the home automation system is as
shown in the figure1. The model consist of different sensors
like temperature, gas, motion and LDR. Initially the Intel
Galileo connects to the internet through WiFi. When the
connection is established it will start reading the parameters
of sensors like p1, p2, p3 etc. The threshold levels for the
required sensors are set as t1, t2, t3 etc. The sensor data are
sent to the web server and stored in the cloud. The data can
be analyzed anywhere any time. If the sensor parameters are
greater than the threshold level then the respective alarm a1,
a2, a3 etc. will be raised and the required actuation is done
for the controlling of the parameters. In the proposed model
the temperature, gas leakage, motion in the house is
monitored. The temperature and the motion detection is
stored in cloud for analysis. If the temperature exceeds the
threshold level then the cooler will turn on automatically
and it will off when the temperature comes to control.
Similarly when there is a leakage of gas in the house alarm is
raised giving the alert sound. The required lights are turned
on/off automatically by detecting the light outside the house.
The user can also monitor the electric appliances through
the internet via web server. If the lights or any electrical
Page 1966

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 03 | June-2015

p-ISSN: 2395-0072

www.irjet.net

appliances are left on in hurry can be seen and turned off

remotely through simply typing the IP address of the web
server.

B. Proposed
Functions

Home

Automation

System

The proposed home automation system has the capabilities

to control the following components in users home and
monitor the following alarms:
Temperature and humidity
Motion detection
Fire and smoke detection
Light level
The proposed home automation system can control
the following appliance:
Lights on/off/dim
Fan on/off
On/off different appliance

C. Software design
Front End Design:
HTML is a format that tells a computer how to
display a web page. The documents themselves are
plain text files with special "tags" or codes that a
web browser uses to interpret and display
information on your computer screen. HTML stands
for Hyper Text Markup Language; an HTML file is a
text file containing small markup tags. The markup
tags tell the Web browser how to display the page.
An HTML files must have an htm or html file
extension.
Cloud Storage:
Cloud computing is the practice of using remote
servers on the internet to manage, store and
process data instead of using a personal computer.
Cloud computing is a general term that is better
divided into three categories: Infrastructure-as-aService, Platform-as-a-Service, and Software-as-aService. IaaS (or utility computing) follows a
traditional utilities model, providing servers and
storage on demand with the consumer paying
accordingly. PaaS allows for the construction of
applications within a providers framework, like
Googles App Engine. SaaS enables customers to use
an application on demand via a browser. A common
example of cloud computing is Gmail, where you
can access your stored data from any computer with
internet access. Here we are using Gmail for the
storage of the data.

D. Implementation Setup

2015, IRJET.NET- All Rights Reserved

Figure. 2 sequence of activities in WHAS

Figure 2 illustrates the sequence of activities in the WHAS.
When the connection is established it will start reading the
parameters of sensors like p1, p2, p3 etc. The threshold
levels for the required sensors are set as t1, t2, t3 etc. The
sensor data are sent to the web server and stored in the
cloud. The data can be analyzed anywhere any time. If the
sensor parameters are greater than the threshold level then
the respective alarm a1, a2, a3 etc. will be raised and the
required actuation is done for the controlling of the
parameters.

Figure 3: Experimental setup of HAS

A model house is built for the home automation system
and is as shown in the figure 3. At the door of the house a
motion sensor is fixed to detect any movement near the
door. Light 1 will turn on automatically when light sensor
detects the darkness. A cooler/Fan will turn on when the
room temperature exceeds the set threshold and in turn
reduces the room temperature. The gas sensor MQ-6 is
placed in the kitchen to detect any gas leakage, if any leakage
is detected the alarm in the hall is raised. Relay is used to
Page 1967

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 03 | June-2015

p-ISSN: 2395-0072

www.irjet.net

switch the electrical appliances like light, fan etc. The Intel
Galileo is placed in store room or garage. The Intel Galileo is
connected with WiFi card with the antennas for the
connectivity with internet.

information about time of motion detected and how many

times as well. All this information is stored in the cloud
which can be checked by the user any time when away from
home.

V. RESULTS

Figure 6: Graph showing the different temperature value

along with the threshold
Figure 4: Web server page
After the successful connection to the server, the data of
sensor are sent to the web server for monitoring of the
system. The figure 4 shows the web server page which will
allow us to monitor and controll the system. By entering the
assigned IP address in the web browser this web server page
will appear. The web server gives the informaton about the
temperature in different places of the house and motion
state in the house. It also gives the status of the various
electrical appliances like light, fan etc which we can control
remotely.

The graph shown in the figure 6 gives the analysis of the

temperature at different time and threshold level of the
temperature. By seeing the graph we can come to know the
change in the temperature. And at what time the
temperature was low/ high. We can also know that was
temperature was above the threshold level or not, if was
above then at what time.

VI. CONCLUSION AND FUTURE WORK

A. Conclusion
The home automation using Internet of Things has been
experimentally proven to work satisfactorily by connecting
simple appliances to it and the appliances were successfully
controlled remotely through internet. The designed system
not only monitors the sensor data, like temperature, gas,
light, motion sensors, but also actuates a process according
to the requirement, for example switching on the light when
it gets dark. It also stores the sensor parameters in the cloud
(Gmail) in a timely manner. This will help the user to analyze
the condition of various parameters in the home anytime
anywhere.

B. Future work

Figure 5: Data base of the sensors data stored in the cloud

All the required data is stored in the cloud (Gmail). The
stored data can be analyzed at anytime and anywhere. The
figure 5 shows the temperature in degree Celsius stored at
different time intervals. And also it shows the state of the
motion detector along with the time. It also provides
2015, IRJET.NET- All Rights Reserved

Using this system as framework, the system can be expanded

to include various other options which could include home
security feature like capturing the photo of a person moving
around the house and storing it onto the cloud. This will
reduce the data storage than using the CCTV camera which
will record all the time and stores it. The system can be
expanded for energy monitoring, or weather stations. This
kind of a system with respective changes can be
implemented in the hospitals for disable people or in
industries where human invasion is impossible or
dangerous, and it can also be implemented for
environmental monitoring.
Page 1968

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 03 | June-2015

p-ISSN: 2395-0072

www.irjet.net

ACKNOWLEDGEMENT
We acknowledge the efforts and hard work by the experts
who have contributed towards development of the different
home automation systems. We also acknowledge the efforts
of Dr. K Natarajan, HoD, TCE, MSRIT and Dr. B P Vijay Kumar,
HoD, ISE for their constant support, suggestions and
modifications to improve the quality of the paper and to help
prepare the camera-ready copy of our paper.

REFERENCES
[1] Sirsath N. S, Dhole P. S, Mohire N. P, Naik S. C &
Ratnaparkhi N.S Department of Computer
Engineering, 44, Vidyanagari, Parvati, Pune-411009,
India University of Pune, Home Automation using
Cloud Network and Mobile Devices
[2] Deepali Javale, Mohd. Mohsin, Shreerang Nandanwar
Home Automation and Security System Using
Android ADK in International Journal of Electronics
Communication and Computer Technology (IJECCT)
Volume 3 Issue 2 (March 2013)
[3] Charith Perera, Student Member, IEEE, Arkady
Zaslavsky, Member, IEEE, Peter Christen,and
Dimitrios Georgakopoulos, Member, IEEE Context
Aware Computing for The Internet of Things: A
Survey. IEEE COMMUNICATIONS SURVEYS &
TUTORIAL
[4] Charith Perera_y, Arkady Zaslavskyy, Peter Christen_
and Dimitrios Georgakopoulosy Research School of
Computer Science, The Australian National
University,Canberra, ACT 0200, Australia yCSIRO ICT
Center, Canberra, ACT 2601, Australia CA4IOT:
Context Awareness for Internet of Things
[5] Bill N. Schilit, Norman Adams, and Roy Want,
Context-Aware Computing Applications
[6] Jayavardhana Gubbi, ,Rajkumar Buyya, Slaven
Marusic,a Marimuthu Palaniswamia, Internet of
Things (IoT): A Vision, Architectural Elements, and
Future Directions
[7] S.P.Pande, Prof.Pravin Sen, Review On: Home
Automation System For Disabled People Using BCI
in IOSR Journal of Computer Science (IOSR-JCE) eISSN: 2278-0661, p-ISSN: 2278-8727 PP 76-80
[8] Basil Hamed, Design & Implementation of Smart
House Control Using LabVIEW at International
Journal of Soft Computing and Engineering (IJSCE)
ISSN: 2231-2307, Volume-1, Issue-6, January 2012
[9] Basma M. Mohammad El-Basioni1, Sherine M. Abd
El-kader2 and Mahmoud Abdelmonim Fakhreldin3,
Smart Home Design using Wireless Sensor Network
and Biometric Technologies at Volume 2, Issue 3,
March 2013
[10] Inderpreet Kaur, Microcontroller Based Home
Automation System With Security at IJACSA)
International Journal of Advanced Computer Science
and Applications, Vol. 1, No. 6, December 2010
2015, IRJET.NET- All Rights Reserved

[11] Rosslin John Robles and Tai-hoon Kim, Review:

Context Aware Tools for Smart
Home
Development, International Journal of Smart Home,
Vol.4, No.1, January, 2010
[12] Hitendra Rawat, Ashish Kushwah, Khyati Asthana,
Akanksha Shivhare, LPG Gas Leakage Detection &
Control System, National Conference on Synergetic
Trends in engineering and Technology (STET-2014)
International Journal of Engineering and Technical
Research ISSN: 2321-0869, Special Issue
[13] Nicholas D., Darrell B., Somsak S., Home
Automation using Cloud Network and Mobile
Devices, IEEE Southeastcon 2012, Proceedings of
IEEE.
[14] Chan, M., Campo, E., Esteve, D., Fourniols, J.Y.,
Smart homes-current features and future
perspectives, Maturitas, vol. 64, issue 2, pp. 90-97,
2009
[15] Das, S.R., Chita, S., Peterson, N., Shirazi, B.A.,
Bhadkamkar, M., Home automation and security for
mobile devices, IEEE PERCOM Workshops, pp. 141146, 2011
[16] S.D.T. Kelly, N.K. Suryadevara, S.C. Mukhopadhyay,
Towards the Implementation of IoT for
Environmental Condition Monitoring in Homes,
IEEE, Vol. 13, pp. 3846-3853, 2013
[17] Rajeev Piyare Internet of Things: Ubiquitous Home
Control and Monitoring System using Android based
Smart Phone International Journal of Internet of
Things
2013,
2(1):
5-11
DOI:
10.5923/j.ijit.20130201.02
[18] G. Kortuem, F. Kawsar, D. Fitton, and
V.Sundramoorthy, "Smart objects as building blocks
for the internet of things," Internet Computing, IEEE,
vol. 14, pp. 44-51, 2010.
[19] S. Hilton. (2012, 14 January). Progression from M2M
to the Internet of Things: an introductory blog.
Available: http://blog.bosch-si.com/progressionfrom-m2m-to-internet-of-things-an-introductoryblog/
[20] C.-H. Chen, C.-C. Gao, and J.-J. Chen, "Intelligent
Home Energy Conservation System Based On WSN,"
presented at the International Conference on
Electrical, Electronics and Civil Engineering, Pattaya,
2011.
[21] R. Piyare and M. Tazil, "Bluetooth based home
automation system using cell phone," in Consumer
Electronics (ISCE), 2011 IEEE 15th International
Symposium on, 2011, pp. 192-195.
[22] Wikipedia. (2012, 12th December). Home
automation.
Available:
http://en.wikipedia.org/wiki/Home_automation
[23] http://www.smartcomputing.com/editorial/article.
asp?article=articles%2
F1995%2Fmar95%2Fpcn0323%2Fpcn0323.asp
retrieved 2010 09 02

Page 1969

International Research Journal of Engineering and Technology (IRJET)

e-ISSN: 2395 -0056

Volume: 02 Issue: 03 | June-2015

p-ISSN: 2395-0072

www.irjet.net

[24] "U.S. Patent 613809: Method of and apparatus for

controlling mechanism of moving vessels and
vehicles". United States Patent and Trademark Office.
1898-11-08. Retrieved 2010-06-16.
[25] William C. Mann (ed.) Smart technology for aging,
disability and independence : the state of the science,
John Wiley and Sons, 2005 0- 471-69694-3, pp. 3466
[26] N. Sriskanthan and Tan Karand. Bluetooth Based
Home
Automation
System.
Journal
of
Microprocessors and Microsystems, Vol. 26, pp.281289, 2002.
[27] Muhammad Izhar Ramli, Mohd Helmy Abd Wahab,
Nabihah, TOWARDS SMART HOME: CONTROL
ELECTRICAL DEVICES ONLINE ,Nornabihah Ahmad
International Conference on Science and Technology:
Application in Industry and Education (2006)
[28] Al-Ali, Member, IEEE & M. AL-Rousan,Java-Based
Home Automation System R. IEEE Transactions on
Consumer Electronics, Vol. 50, No. 2, MAY 2004
[29] BCC Research, Sensors: Technologies and global
markets,
[30] BCC Research, Market Forecasting,March 2011,
http://www.bccresearch.
com/report/sensorstechnologies-markets-ias006d.html [Accessed on:
2012-01-05].
[31] European Commission, Internet of things in 2020
road map for the future, Working Group RFID of the
ETP
EPOSS,
Tech.
Rep.,
May
2008,
http://ec.europa.eu/informationsociety/policy/rfid/
documents/iotprague2009.pdf [Accessed on: 201106-12].
[32] T. Lu and W. Neng, Future internet: The internet of
things, in 3rd International Conference on Advanced
Computer Theory and Engineering (ICACTE), vol. 5,
August 2010, pp. V5376V5380. Available:
http://dx.doi.org/10.1109/ICACTE.2010.5579543.

2015, IRJET.NET- All Rights Reserved

[33] P. Guillemin and P. Friess, Internet of things

strategic research roadmap, The Cluster of
European Research Projects, Tech. Rep., September
2009,
http://www.internet-of-thingsresearch.eu/pdf/IoT Cluster Strategic Research
Agenda 2009.pdf [Accessed on: 2011-08- 15].
[34] ]. Vishwajeet H.Bhide A Survey on the Smart
Homes using Internet of Things (IoT)
[35] Volume 2, Issue 12, December 2014 International
Journal of Advance Research in Computer Science
and Management Studies Research Article / Survey
Paper / Case Study
[36] Rahul Godha, Sneh Prateek, Nikhita Kataria Home
Automation: Access Control for IoT Devices
International Journal of Scientific and Research
Publications, Volume 4, Issue 10, October 2014 1
ISSN 2250-3153

BIOGRAPHIES
Vinay Sagar K N pursuing M. Tech.
in Digital Communication, TCE,
MSRIT

Kusuma S M working as Asst.

Professor at M S Ramaiah Institute
of Technology. She has published
many national and international
research papers. She has very
depth knowledge of his research
areas.

Page 1970