Scribd
Upload
200 views

User Manual of Wind Generators

The document is an owner's manual for a wind turbine generator. It contains important safety instructions, technical specifications for different models of the turbine, instructions for assembly and installation, maintenance recommendations, an exploded view and parts list. The manual instructs to read all safety instructions before operating the turbine, properly ground the turbine, and not install it on a windy day. It also warns that the rotating blades pose a serious mechanical hazard.

Uploaded by

Smith
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
200 views

User Manual of Wind Generators

The document is an owner's manual for a wind turbine generator. It contains important safety instructions, technical specifications for different models of the turbine, instructions for assembly and installation, maintenance recommendations, an exploded view and parts list. The manual instructs to read all safety instructions before operating the turbine, properly ground the turbine, and not install it on a windy day. It also warns that the rotating blades pose a serious mechanical hazard.

Uploaded by

Smith
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Wind turbine generator

Owners Manual

Installation Operation Maintenan

CE & TUV

One Important Safety Instructions


READ THESE INSTRUCTIONS BEFORE ASSEMBLING,INSTAKKING OR OPERATING YOUR PRODUCT.
1. SAVE THESE INSTRUCTIONS. This manual contains important instructions that must
be followed during assembly, installation and maintenance.
2. Read, understand and respect all warnings.
3. Do not install wind turbine on a windy day.
4. If unusual noise or operation is experienced, turn off machine and contact authorized
service personal.
5. During assembly and installation properly torque all fasteners.
6. Use only proper grounding techniques as established by the NEC.
7. Wind turbine codes. Failure to comply with manual and local codes may affect and
possibly void your warranty.
8. Rotating blades are a serious mechanical hazard. Install wind turbine so no one can come
into contact with blades.

Owners

Manual

FA1.2 series Technical Specifications


Model

DF-200

DF-300

DF-400

Rated Power(W)

200

300

400

Rotor Voltage(V)

12/24

12/24

12/24

Rotor diameter(M)

1.2

1.2

1.2

Star up wind speed(M/S)

Cast aluminum

Body
Blades

3-Carbon fiber composite/3-composite material

Owners

Manual

3-Carbon fiber composite

Warning:Don
Warning:Dont attempt to
mount the turbine while
blades are spinning

Turbine Assembly
Your wind turbine delivered partially assembled. Assembly
requires mounting the blades on the blade hub, securing
the hub to the turbine body and installing the nose cone
on the blade hub. The necessary hex wrenches are
furnished with FA1.2 Series.

If the wind turbine is to be installed after the tower is


erected, it will be safer and easier to
first install the turbine body on the tower and
then install the hub/ blade assembly. This will
avoid attempting to mount the turbine while
the blades are spinning-a dangerous condition.

Pass a bolt through the blade and screw it into the locknut-do
not fully tighten the bolt yet. Install the second bolt and
lock-nut and torque both to 7.45ft-Ibs(10Nm). Install the remaining
two blades following the same procedure.
If the wind turbine is to be installed on a tilt-up tower, mount the
blade/hub assembly to the turbine now. Start the M16 hub nut on
shaft thread and spin the hub completely onto the turbine alternator
shaft. Fully tighten the hub to 48 ft-Ibs (65Nm) by inserting a hex key wrench
in the turbine alternator shaft and turning the shaft while turning the blades.
Mount the nosecone into position over the outside edges of the blade hub.
Nose cone bolts, M4*10mm,3Ib-ft.

Owners

Manual

Remarks: The output of wind turbine generator is DC( The red wire is anode ,the black wire is negative electrode, the
blue wire is ground wire) The red wire and the black wire are connect
ed with any two terminals of charging controller,
connected
there is no need to distinguish positive and negative. The ground wire is connected with screw of the tower foundation
foundation..
Please refer to the following picture.

Charge controller

Wind Turbine Generator

Owners

Manual

Maintenance
Although your wind turbine has been designed to run for long periods without requiring any maintenance, reliability and
performance will be enhanced if you periodically inspect your system.
CAUTION: Never approach the turbine during operation.
After blades for chips or nicks. Replace blades if damaged. Do not operate the turbine with chipped or unbalanced blades.
This can cause severe wear, damage, and possible failure. Do not install individual blades. The blades are balanced as sets.
Check the blade bolts and the hub but for tightness.
Check nosecone for cracks and proper fit.
Wash off any built-up dirt or debris from the blades.
Check all electrical connections to make sure they are tight and free from corrosion.
As with all charging systems, check your battery water levels and add distilled water in accordance with manufactures
recommendation.
We suggest replacing the blades and bearing every five years for optimal performance.

Owners

Manual

Exploded view & parts list

Owners

Manual

Item

Description

Qty

Nose cone

Blade

Blade hub

Nacelle body assy

Clamp body

tower

You might also like