Scribd
Upload
3K views3 pages

Flash Codes For CAT 120-H Motor Grader PDF

(1) This document provides steps to retrieve transmission diagnostics from a machine's transmission ECM. It notes that the machine must be parked with the parking brake applied during this process. (2) The first step is to remove the sheet metal panel covering the transmission ECM. Then locate the transmission indicator lamp on the front of the steering wheel. Placing the key in the run position without starting the engine will cause the lamp to flash the transmission configuration code. (3) Uncoupling the diagnostic plug will put the ECM in active diagnostic mode, flashing any active faults followed by a pause before repeating. Reconnecting the plug ends this mode.

Uploaded by

surianto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views3 pages

Flash Codes For CAT 120-H Motor Grader PDF

(1) This document provides steps to retrieve transmission diagnostics from a machine's transmission ECM. It notes that the machine must be parked with the parking brake applied during this process. (2) The first step is to remove the sheet metal panel covering the transmission ECM. Then locate the transmission indicator lamp on the front of the steering wheel. Placing the key in the run position without starting the engine will cause the lamp to flash the transmission configuration code. (3) Uncoupling the diagnostic plug will put the ECM in active diagnostic mode, flashing any active faults followed by a pause before repeating. Reconnecting the plug ends this mode.

Uploaded by

surianto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

(1) Transmission indicator lamp.

NOTICE
While using this procedure to retrieve transmission diagnostics from
the transmission ECM, the machine must be parked with parking
brake Applied.

This process is not as easy to use as the ECAP nor is the capability as complete. This capability has been provided
for the user who does not have ready access to an ECAP.
Follow the steps to obtain transmission diagnostics from the ECM.

NOTE: The preceding chart has changed from the former issue.

(2) Diagnostic plug. (3) ECM.

1. Remove sheet metal panel covering the transmission ECM (3).


2. Locate the transmission indicator lamp (1) located in front of the steering wheel.
3. Place the Start/Stop Key Switch in the Run position with engine off. When the machine Start/Stop Key Switch
is turned to the ON position, the machine will display the Transmission Configuration Code as part of normal
operation. For example, when the Start/Stop Key of a 140H is turned to ON, a "41" code will be displayed on the
EMS transmission indicator lamp (1). The lamp will flash four times in rapid succession followed with a one
second pause followed by one additional flash.
4. To enter the Diagnostic Mode of the transmission ECM, uncouple the diagnostic plug (2). At this point the ECM
automatically defaults to the Active Diagnostic Mode. In the Active Diagnostic Mode the ECM will flash out the
first Active Fault in memory followed by a three second pause and then repeating the original fault. The original
fault will continue to be repeated until the diagnostic plug (2) is reconnected.
5. To enter the Active Diagnostic Scroll Mode, jumper sockets 1 and 2 of the diagnostic receptacle of the
diagnostic plug (2). The control will display all diagnostics that are presently active on the system. A three second
pause separates the codes as they are displayed. Removing the jumper while the control is displaying a diagnostic
code will cause the control to repeatedly display that code. Replacing the jumper resumes scrolling.
6. To enter the Logged Diagnostic Scroll Mode, jumper sockets 1 and 3 of the diagnostic receptacle. The ECM will
now display any faults which have occurred which are not presently active. A Diagnostic Code of "12" indicates
there are no Logged Faults present. Removing the jumper wire while the control is displaying a Diagnostic Code
will cause the control to repeatedly display that code. Replacing the 1 to 3 jumper resumes scrolling.
7. This mode is used to clear Logged Diagnostics from memory. To erase a code, put the control in the Logged
Diagnostic Scroll Mode until the desired code is displayed and then remove the jumper. The ECM will continue to
display the desired code. Jumper receptacle socket 1 to 4. The transmission indicator lamp (1) will turn off
indicating the code has been erased. The lamp will remain off until either the Logged Diagnostic Scroll Mode or
the Active Diagnostic Scroll Mode is re-entered. The above process can be repeated until there are no codes stored
in memory. An active diagnostic code cannot be erased from memory.

You might also like