Scribd
Upload
317 views2 pages

TDS - Concresive ZR

CONCRESIVE ZR is a single component zinc rich epoxy primer for steel. It provides galvanic protection to steel and is used to coat reinforcing bars in concrete or as a touch-up primer. It has advantages like excellent adhesion and corrosion protection for steel. It is applied by brush after surface preparation and dries within 20 minutes.

Uploaded by

Venkata Rao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
317 views2 pages

TDS - Concresive ZR

CONCRESIVE ZR is a single component zinc rich epoxy primer for steel. It provides galvanic protection to steel and is used to coat reinforcing bars in concrete or as a touch-up primer. It has advantages like excellent adhesion and corrosion protection for steel. It is applied by brush after surface preparation and dries within 20 minutes.

Uploaded by

Venkata Rao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

CONCRESIVE

ZR
Single component epoxy based zinc rich
primer for steel
Description

Standards

CONCRESIVE ZR is a single component, solvent borne zinc


rich epoxy primer, providing active galvanic protection to
steel. It is a thick grey liquid of paint-like consistency,
recommended for use where chloride induced attack on
steel and concrete is involved.

CONCRESIVE ZR is formulated to meet the scope of BS


4652, 1971 Type 2.

Primary uses

Surface preparation:
The steel surfaces should be or grit blasted or wire brushed
to remove all traces of corrosion. Ensure no oil, grease or
dust is present. Surfaces should be dry.

As a protective coating to steel reinforcing bars in


concrete.
As a touch-up primer for damaged galvanised metal.
As a primer for steel substrates prior to suitable top
coating.

Apply CONCRESIVE ZR immediately after completion of


preparation to prevent any contamination. Do not leave
blasted or prepared steel uncoated.
Mixing:
CONCRESIVE ZR should be thoroughly mixed prior to
application.

Advantages

Application procedure

Provides positive protection of steel components against


corrosion.
Excellent adhesion to steel.
Easy to use single component material.
No pot-life restrictions or wastage.
Short overcoating time.

Application:
Brush the CONCRESIVE ZR onto the prepared substrate,
ensuring uniform and full coverage, particularly on the back
face of reinforcement. Repair mortars can be applied as
soon as the CONCRESIVE ZR is dry.

Long term exposure

Packaging
CONCRESIVE ZR is a single component system, supplied
in 1 litre units.

CONCRESIVE ZR is not designed as a finished coating.


Although protection to the steel will be provided for some
time, overcoating should be carried out as soon as possible,
particularly in aggressive environments.

Typical properties*
Coverage
Appearance:
Specific gravity:
Tack free time: (approximate)
Recoat time :
T.Z.C. in DFT
D.F.T. per coat:
Application temperature:

thick grey liquid


1.84 at 25C
20 mins at 25C
5 mins at 40C
5 hours at 25C
2 hours at 40C
>90%
>50 microns
min. 10C
max. 40C

When used for coating steel 1 litre of CONCRESIVE ZR will


cover 165 linear metres of 16mm diameter bar per coat and
pro rata or 7.5m/litre/coat.

Equipment care
Tools should be cleaned with SOLVENT NO. 2 immediately
after use.

Storage
Store under cover out of direct sunlight and protect from
extremes of temperature. In tropical climates the product
must be stored in an air-conditioned environment. Shelf life
is at least 12 months when stored as above.
Failure to comply with the recommended storage conditions
may result in premature deterioration of the product or
packaging. For specific storage advice consult Degussa's
Technical Services Department.

Safety precautions
As with all chemical products, care should be taken during
use and storage to avoid contact with eyes, mouth, skin and
foodstuffs. Treat splashes to eyes and skin immediately. If
accidentally ingested, seek immediate medical attention.
Reseal containers after use.

Note
Field service, where provided, does not constitute
supervisory responsibility. For additional information contact
your local Degussa representative.
Degussa reserves the right to have the true cause of any
difficulty determined by accepted test methods.

Quality and care


All products originating from Degussas Dubai, UAE facility
are manufactured under a management system
independently certified to conform to the requirements of the
quality, environmental and occupational health & safety
standards ISO 9001, ISO 14001 and OHSAS 18001.
12/94 Degussa-UAE revised 02/2004

* Properties listed are only for guidance and are not a guarantee of
performance.

Degussa Construction Chemicals UAE LLC


P.O. Box 37127, Dubai, UAE
Tel: +971 4 8851000

Fax: +971 4 8851002

www.degussa-cc.ae

e-mail: [email protected]

Whilst any information contained herein is true, accurate and


represents our best knowledge and experience, no warranty is given or
implied with any recommendations made by us, our representatives or
distributors, as the conditions of use and the competence of any labour
involved in the application are beyond our control.

Certificate No.
963680

As all Degussa technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.

Certificate No.
945787

Certificate No.
772556

You might also like