Scribd
Upload
146 views

Ccna2 Assignment 2

The document contains configuration information for three switches (S1, S2, S3) and three routers (R1, R2, R3). The switches and routers are configured with hostnames, passwords, and interfaces. OSPF routing is configured on the routers with neighboring routers displayed in the show ip ospf neighbor output.

Uploaded by

Muhammad AfNanz
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
146 views

Ccna2 Assignment 2

The document contains configuration information for three switches (S1, S2, S3) and three routers (R1, R2, R3). The switches and routers are configured with hostnames, passwords, and interfaces. OSPF routing is configured on the routers with neighboring routers displayed in the show ip ospf neighbor output.

Uploaded by

Muhammad AfNanz
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 34

Switch 1

CONFIGURATION
Switch>en
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname S1
S1(config)#line console 0
S1(config-line)#password cisco
S1(config-line)#exit
S1(config)#line vty 04
S1(config-line)#password unikl
S1(config-line)#exit
S1(config)#enable password miit
S1(config)#banner motd "Welcome to S1"
S1(config)#exit

SHOW RUN

Welcome to S1

S1>en
Password:
S1#show run
Building configuration...

Current configuration : 1140 bytes


!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname S1
!
enable password miit
!
!
!
!
!
spanning-tree mode pvst
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!

interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!

interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface Vlan1
no ip address
shutdown
!
banner motd ^CWelcome to S1^C
!
!
!
line con 0
password cisco
!
line vty 0 3
login
line vty 4
password unikl
login
line vty 5 15
login
!
!

End

Switch 2
CONFIGURATION
Switch>en
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname S2
S2(config)#line console 0
S2(config-line)#password cisco
S2(config-line)#exit
S2(config)#line vty 04
S2(config-line)#password unikl
S2(config-line)#exit
S2(config)#enable password miit
S2(config)#banner motd "Welcome to S2"
S2(config)#exit

SHOW RUN
Welcome to S2

S2>en
Password:

S2#show run
Building configuration...

Current configuration : 1140 bytes


!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname S2
!
enable password miit
!
!
!
!
!
spanning-tree mode pvst
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!

interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!

interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface Vlan1
no ip address
shutdown
!
banner motd ^CWelcome to S2^C
!
!
!
line con 0
password cisco
!
line vty 0 3
login
line vty 4
password unikl
login
line vty 5 15
login
!
!
end

Switch 3
CONFIGURATION
Switch>en
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname S3
S3(config)#line console 0
S3(config-line)#password cisco
S3(config-line)#exit
S3(config)#line vty 04
S3(config-line)#password unikl
S3(config-line)#exit
S3(config)#enable password miit
S3(config)#banner motd "Welcome to S3"
S3(config)#exit

SHOW RUN
Welcome to S3

S3>en
Password:
S3#show run
Building configuration...

Current configuration : 1140 bytes

!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname S3
!
enable password miit
!
!
!
!
!
spanning-tree mode pvst
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!

interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!

interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface Vlan1
no ip address
shutdown
!
banner motd ^CWelcome to S3^C
!
!
!
line con 0
password cisco
!
line vty 0 3
login
line vty 4
password unikl
login
line vty 5 15
login
!
!
end

Router 1
CONFIGURATION
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#line console 0
R1(config-line)#password cisco
R1(config-line)#exit
R1(config)#service password-encryption
R1(config)#line vty 04
R1(config-line)#password unikl
R1(config-line)#exit
R1(config)#enable password miit
R1(config)#banner motd "Welcome to R1"
R1(config)#exit

SHOW RUN
Welcome to R1

R1>en
Password:
R1#show run
Building configuration...

Current configuration : 1245 bytes


!
version 15.1
no service timestamps log datetime msec

no service timestamps debug datetime msec


service password-encryption
!
hostname R1
!
!
!
enable password 7 082C45471D
!
!
!
!
no ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO1941/K9 sn FTX15240NFJ
!
!
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
!

!
!
!
!
!
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0
ip address 200.100.1.1 255.255.255.252
clock rate 2000000
!
interface Serial0/0/1
ip address 200.100.5.2 255.255.255.252
clock rate 2000000
!
interface Serial0/1/0
ip address 200.100.6.1 255.255.255.252
clock rate 2000000
!
interface Serial0/1/1
no ip address
clock rate 2000000
shutdown

!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
network 200.100.2.0 0.0.0.3 area 0
network 200.100.1.0 0.0.0.3 area 0
network 192.168.1.0 0.0.0.3 area 0
network 192.168.1.0 0.0.0.255 area 0
!
ip classless
!
ip flow-export version 9
!
!
!
banner motd ^CWelcome to R1^C
!
!
!
!
line con 0
password 7 0822455D0A16
!
line aux 0
!
line vty 0 3
login
line vty 4
password 7 083442470215

login
!
!
!
end

SHOW IP OSPF
R1#show ip ospf neighbor
Neighbor ID

Pri State

200.100.2.1

0 FULL/ -

Dead Time Address


00:00:37

200.100.1.2

Interface
Serial0/0/0

Router 2
CONFIGURATION
Router>EN
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#line console 0
R2(config-line)#password cisco
R2(config-line)#exit
R2(config)#line vty 04
R2(config-line)#password unikl
R2(config-line)#exit
R2(config)#service password-encryption
R2(config)#enable password miit
R2(config)#banner motd "Welcome to R2"
R2(config)#exit

SHOW RUN
Welcome to R2

R2>en
Password:
R2#show run
Building configuration...

Current configuration : 1143 bytes


!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
service password-encryption
!
hostname R2
!
!
!
enable password 7 082C45471D
!
!
!
!
no ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO1941/K9 sn FTX1524ZJCC
!
!
!
!

!
!
!
!
!
!
!
spanning-tree mode pvst
!
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
shutdown
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0
ip address 200.100.2.1 255.255.255.252
clock rate 2000000
!
interface Serial0/0/1
ip address 200.100.1.2 255.255.255.252

clock rate 2000000


!
interface Serial0/1/0
no ip address
clock rate 2000000
shutdown
!
interface Serial0/1/1
no ip address
clock rate 2000000
shutdown
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
network 200.100.1.0 0.0.0.3 area 0
network 200.100.2.0 0.0.0.3 area 0
!
ip classless
!
ip flow-export version 9
!
!
!
banner motd ^CWelcome to R2^C
!
!
!
!

line con 0
password 7 0822455D0A16
!
line aux 0
!
line vty 0 3
login
line vty 4
password 7 083442470215
login
!
!
!
end

SHOW IP OSPF
R2#show ip ospf neighbor
Neighbor ID

Pri State

Dead Time Address

Interface

200.100.3.1

0 FULL/ -

00:00:35

200.100.2.2

Serial0/0/0

200.100.6.1

0 FULL/ -

00:00:39

200.100.1.1

Serial0/0/1

Router 3
CONFIGURATION
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3

R3(config)#line console 0
R3(config-line)#password cisco
R3(config-line)#exit
R3(config)#service password-encryption
R3(config)#line vty 04
R3(config-line)#password unikl
R3(config-line)#exit
R3(config)#enable password miit
R3(config)#banner motd "Welcome to R3 "
R3(config)#exit

SHOW RUN
Welcome to R3

R3>en
Password:
R3#show run
Building configuration...

Current configuration : 1144 bytes


!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
service password-encryption
!
hostname R3
!
!
!
enable password 7 082C45471D
!

!
!
!
no ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO1941/K9 sn FTX15242KLS
!
!
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
!
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto

shutdown
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0
ip address 200.100.3.1 255.255.255.252
clock rate 2000000
!
interface Serial0/0/1
ip address 200.100.2.2 255.255.255.252
clock rate 2000000
!
interface Serial0/1/0
no ip address
clock rate 2000000
shutdown
!
interface Serial0/1/1
no ip address
clock rate 2000000
shutdown
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes

network 200.100.2.0 0.0.0.3 area 0


network 200.100.3.0 0.0.0.3 area 0
!
ip classless
!
ip flow-export version 9
!
!
!
banner motd ^CWelcome to R3 ^C
!
!
!
!
line con 0
password 7 0822455D0A16
!
line aux 0
!
line vty 0 3
login
line vty 4
password 7 083442470215
login
!
!
!
end

SHOW IP OSPF
R3#show ip ospf neighbor
Neighbor ID

Pri State

Dead Time Address

Interface

200.100.6.2

0 FULL/ -

00:00:39

200.100.3.2

Serial0/0/0

200.100.2.1

0 FULL/ -

00:00:39

200.100.2.1

Serial0/0/1

Router 4
CONFIGURATION
Router>en
Router#config t
Router(config)#hostname R4
R4(config)#line console 0
R4(config-line)#password cisco
R4(config-line)#exit
R4(config)#service password-encryption
R4(config)#line vty 04
R4(config-line)#password unikl
R4(config-line)#exit
R4(config)#enable password miit
R4(config)#banner motd "Welcome to R4"
R4(config)#exit

SHOW RUN
Welcome to R4

R4>en
Password:
R4#show run
Building configuration...

Current configuration : 1245 bytes


!
version 15.1
no service timestamps log datetime msec

no service timestamps debug datetime msec


service password-encryption
!
hostname R4
!
!
!
enable password 7 082C45471D
!
!
!
!
no ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO1941/K9 sn FTX1524P67G
!
!
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
!

!
!
!
!
!
interface GigabitEthernet0/0
ip address 192.168.3.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0
ip address 200.100.4.1 255.255.255.252
clock rate 2000000
!
interface Serial0/0/1
ip address 200.100.3.2 255.255.255.252
clock rate 2000000
!
interface Serial0/1/0
no ip address
clock rate 2000000
shutdown
!
interface Serial0/1/1
ip address 200.100.6.2 255.255.255.252
clock rate 2000000

!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
network 200.100.3.0 0.0.0.3 area 0
network 200.100.4.0 0.0.0.3 area 0
network 200.100.6.0 0.0.0.3 area 0
network 192.168.3.0 0.0.0.255 area 0
!
ip classless
!
ip flow-export version 9
!
!
!
banner motd ^CWelcome to R4^C
!
!
!
!
line con 0
password 7 0822455D0A16
!
line aux 0
!
line vty 0 3
login
line vty 4
password 7 083442470215

login
!
!
!
end

SHOW IP OSPF
R4#show ip ospf neighbor
Neighbor ID

Pri State

Dead Time Address

Interface

200.100.3.1

0 FULL/ -

00:00:30

200.100.3.1

Serial0/0/1

200.100.5.1

0 FULL/ -

00:00:30

200.100.4.2

Serial0/0/0

Router 5
CONFIGURATION
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R5
R5(config)#line console 0
R5(config-line)#password cisco
R5(config-line)#exit
R5(config)#service password-encryption
R5(config)#line vty 04
R5(config-line)#password unikl
R5(config-line)#exit
R5(config)#enable password miit
R5(config)#banner motd "Welcome to R5"

R5(config)#exit

SHOW RUN
Welcome to R5

R5>en
Password:
R5#show run
Building configuration...

Current configuration : 1194 bytes


!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
service password-encryption
!
hostname R5
!
!
!
enable password 7 082C45471D
!
!
!
!
no ip cef
no ipv6 cef
!
!
!

!
license udi pid CISCO1941/K9 sn FTX1524L972
!
!
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
!
!
!
!
!
!
interface GigabitEthernet0/0
ip address 192.168.2.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0

ip address 200.100.5.1 255.255.255.252


clock rate 2000000
!
interface Serial0/0/1
ip address 200.100.4.2 255.255.255.252
clock rate 2000000
!
interface Serial0/1/0
no ip address
clock rate 2000000
shutdown
!
interface Serial0/1/1
no ip address
clock rate 2000000
shutdown
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
network 200.100.4.0 0.0.0.3 area 0
network 200.100.5.0 0.0.0.3 area 0
network 192.168.2.0 0.0.0.255 area 0
!
ip classless
!
ip flow-export version 9
!
!

!
banner motd ^CWelcome to R5^C
!
!
!
!
line con 0
password 7 0822455D0A16
!
line aux 0
!
line vty 0 3
login
line vty 4
password 7 083442470215
login
!
!
!
end

SHOW IP OSPF
R5#show ip ospf neighbor
Neighbor ID
200.100.6.2

Pri State
0 FULL/ -

Dead Time Address


00:00:33

200.100.4.1

Interface
Serial0/0/1

You might also like