Scribd
Upload
305 views

Beeps Code

Hardware

Uploaded by

Maqsood Ahmed Pathan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
305 views

Beeps Code

Hardware

Uploaded by

Maqsood Ahmed Pathan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Page 1

Computer POST and beep codes

The computer POST (power-on self-test) checks a


computer's internal hardware for compatibility and connection before starting the remainder of
the boot process. If the computer passes the POST, the computer may give a single beep (some
computers may beep twice) as it starts and continue to boot. However, if the computer fails the
POST, the computer will either not beep or generate a beep code that tells the user the source of
the problem.
If your computer has an irregular POST or a beep code not mentioned below, follow the POST
troubleshooting steps to determine the failing hardware component.
AMI BIOS beep codes
Award BIOS beep codes
Dell beep codes
IBM BIOS beep codes
Macintosh startup tones
Phoenix BIOS beep codes
Motherboard help

Page 2

AMI BIOS beep codes

Below are the AMI BIOS Beep codes that can occur. However, because of the wide variety of
different computer manufacturers with this BIOS, the beep codes may vary.
Beep Code
Descriptions
1 short
DRAM refresh failure
2 short
Parity circuit failure
3 short
Base 64K RAM failure
4 short
System timer failure
5 short
Process failure
6 short
Keyboard controller Gate A20 error
7 short
Virtual mode exception error
8 short
Display memory Read/Write test failure
9 short
ROM BIOS checksum failure
10 short
CMOS shutdown Read/Write error
11 short
Cache Memory error
1 long, 3 short Conventional/Extended memory failure
1 long, 8 short Display/Retrace test failed
two-tone siren Low CPU Fan speed, Voltage Level issue

AWARD BIOS beep codes

Below are Award BIOS Beep codes that can occur. However, because of the wide variety of
different computer manufacturers with this BIOS, the beep codes may vary.
Beep Code

1 long, 2 short

1 long, 3 short
Beeps repeating endlessly
Repeated high frequency
beeps while PC is running
Repeated beeps alternating
high & low frequency

Description
Indicates a video error has occurred and the BIOS cannot
initialize the video screen to display any additional information
Video card not detected (reseat video card) or bad video card
RAM problem.
Overheating processor (CPU)

Issue with the processor (CPU), possibly damaged

If any other correctable hardware issues are found, the BIOS displays a message.

Page 3

Dell beep codes


Beep Code

Description
1 beep
BIOS ROM corruption or failure
2 beeps
Memory (RAM) not detected
3 beeps
Motherboard failure
4 beeps
Memory (RAM) failure
5 beeps
CMOS Battery failure
6 beeps
Video card failure
7 beeps
Bad processor (CPU)
For other Dell beep codes, please refer to Dell's Beep Codes and PSA Diagnostics Chart page.

IBM BIOS beep codes

Below are general IBM BIOS Beep codes that can occur. However, because of the wide variety
of models shipping with this BIOS, the beep codes may vary.
Beep Code

Description
No Beeps
No Power, Loose Card, or Short.
1 Short Beep
Normal POST, computer is ok.
2 Short Beep
POST error, review screen for error code.
Continuous Beep
No Power, Loose Card, or Short.
Repeating Short Beep
No Power, Loose Card, or Short.
1 Long and 1 Short Beep
Motherboard issue.
1 Long and 2 Short Beeps
Video (Mono/CGA Display Circuitry) issue.
1 Long and 3 Short Beeps.
Video (EGA) Display Circuitry.
3 Long Beeps
Keyboard or Keyboard card error.
1 Beep, Blank or Incorrect Display Video Display Circuitry.
Macintosh startup tones
Tones
Error
Error Tone. (two sets of different tones) Problem with logic board or SCSI bus.
Startup tone, drive spins, no video
Problem with video controller.
Powers on, no tone.
Logic board problem.
High Tone, four higher tones.
Problem with SIMM.

Page 4

Phoenix BIOS beep codes

Below are the beep codes for Phoenix BIOS Q3.07 OR 4.X
Beep Code

1-1-1-1
1-1-1-3
1-1-2-1
1-1-2-3
1-1-3-1
1-1-3-2
1-1-3-3
1-1-4-1
1-1-4-3
1-2-1-1
1-2-1-2
1-2-1-3
1-2-2-1
1-2-2-3
1-2-3-1
1-2-3-3
1-2-4-1
1-3-1-1
1-3-1-3
1-3-2-1
1-3-3-1
1-3-3-3
1-3-4-1
1-3-4-3
1-4-1-3
1-4-2-4
1-4-3-1
1-4-3-2
1-4-3-3
1-4-4-1
1-4-4-2
2-1-1-1

Description and what to check


Unconfirmed beep code. Reseat RAM chips or replace RAM chips as possible
solution
Verify Real Mode.
Get CPU Type.
Initialize system hardware.
Initialize chipset registers with initial POST values.
Set in POST flag.
Initialize CPU registers.
Initialize cache to initial POST values.
Initialize I/O.
Initialize Power Management.
Load alternate registers with initial POST values.
Jump to UserPatch0.
Initialize keyboard controller.
BIOS ROM checksum.
8254 timer initialization.
8237 DMA controller initialization.
Reset Programmable Interrupt Controller.
Test DRAM refresh.
Test 8742 Keyboard Controller.
Set ES segment to register to 4 GB.
28 Autosize DRAM.
Clear 512K base RAM.
Test 512 base address lines.
Test 512K base memory.
Test CPU bus-clock frequency.
Reinitialize the chipset.
Shadow system BIOS ROM.
Reinitialize the cache.
Autosize cache.
Configure advanced chipset registers.
Load alternate registers with CMOS values.
Set Initial CPU speed.

Page 5

2-1-1-3
2-1-2-1
2-1-2-3
2-1-2-4
2-1-3-1
2-1-3-2
2-1-3-3
2-1-4-1
2-1-4-3
2-2-1-1
2-2-1-3
2-2-2-1
2-2-2-3
2-2-3-1
2-2-3-3
2-2-4-1
2-3-1-1
2-3-1-3
2-3-2-1
2-3-2-3
2-3-3-1
2-3-3-3
2-3-4-1
2-3-4-3
2-4-1-1
2-4-1-3
2-4-2-1
2-4-2-3
2-4-4-1
2-4-4-3
3-1-1-1
3-1-1-3
3-1-2-1
3-1-2-3
3-1-3-1
3-1-3-3
3-1-4-1
3-2-1-1

Initialize interrupt vectors.


Initialize BIOS interrupts.
Check ROM copyright notice.
Initialize manager for PCI Options ROMs.
Check video configuration against CMOS.
Initialize PCI bus and devices.
Initialize all video adapters in system.
Shadow video BIOS ROM.
Display copyright notice.
Display CPU Type and speed.
Test keyboard.
Set key click if enabled.
56 Enable keyboard.
Test for unexpected interrupts.
Display prompt Press F2 to enter SETUP.
Test RAM between 512 and 640k.
Test expanded memory.
Test extended memory address lines.
Jump to UserPatch1.
Configure advanced cache registers.
Enable external and CPU caches.
Display external cache size.
Display shadow message.
Display non-disposable segments.
Display error messages.
Check for configuration errors.
Test real-time clock.
Check for keyboard errors
Set up hardware interrupts vectors.
Test coprocessor if present.
Disable onboard I/O ports.
Detect and install external RS232 ports.
Detect and install external parallel ports.
Re-initialize onboard I/O ports.
Initialize BIOS Data Area.
Initialize Extended BIOS Data Area.
Initialize floppy controller.
Initialize hard disk controller.

Page 6

3-2-1-2
3-2-1-3
3-2-2-1
3-2-2-3
3-2-3-1
3-2-3-3
3-2-4-1
3-2-4-3
3-3-1-1
3-3-1-3
3-3-3-1
3-3-3-3
3-3-4-1
3-3-4-3
3-4-1-1
3-4-1-3
3-4-2-1
3-4-2-3
3-4-3-1
3-4-4-1
3-4-4-3
3-4-4-4
4-1-1-1
4-2-1-1
4-2-1-3
4-2-2-1
4-2-2-3
4-2-3-1
4-2-3-3
4-2-4-1
4-3-1-3
4-3-1-4
4-3-2-1
4-3-2-2
4-3-2-3
4-3-2-4
4-3-3-1
4-3-3-2

Initialize local bus hard disk controller.


Jump to UserPatch2.
Disable A20 address line.
Clear huge ES segment register.
Search for option ROMs.
Shadow option ROMs.
Set up Power Management.
Enable hardware interrupts.
Set time of day.
Check key lock.
Erase F2 prompt.
Scan for F2 key stroke.
Enter SETUP.
Clear in POST flag.
Check for errors
POST done - prepare to boot operating system.
One beep.
Check password (optional).
Clear global descriptor table.
Clear parity checkers.
Clear screen (optional).
Check virus and backup reminders.
Try to boot with INT 19.
Interrupt handler error.
Unknown interrupt error.
Pending interrupt error.
Initialize option ROM error.
Shutdown error.
Extended Block Move.
Shutdown 10 error.
Initialize the chipset.
Initialize refresh counter.
Check for Forced Flash.
Check HW status of ROM.
BIOS ROM is OK.
Do a complete RAM test.
Do OEM initialization.
Initialize interrupt controller.

Page 7

4-3-3-3
4-3-3-4
4-3-4-1
4-3-4-2
4-3-4-3
two-tone
siren

Read in bootstrap code.


Initialize all vectors.
Boot the Flash program.
Initialize the boot device.
Boot code was read OK.

Low CPU Fan speed, Voltage Level issue

You might also like