Scribd
Upload
826 views

Flakiness & Elongation Index

This document describes procedures for determining the flakiness and elongation indices of aggregate samples. The flakiness index test involves separating particles that have a thickness less than 60% of the sieve size. The elongation index test separates particles with a length over 180% of the sieve size. Samples are sieved into fractions and particles not meeting the shape criteria are weighed. The flakiness and elongation indices are the percentages of misshapen particles for each fraction. Proper aggregate shape is important for workability and strength in concrete and stability in granular bases.

Uploaded by

vino
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
826 views

Flakiness & Elongation Index

This document describes procedures for determining the flakiness and elongation indices of aggregate samples. The flakiness index test involves separating particles that have a thickness less than 60% of the sieve size. The elongation index test separates particles with a length over 180% of the sieve size. Samples are sieved into fractions and particles not meeting the shape criteria are weighed. The flakiness and elongation indices are the percentages of misshapen particles for each fraction. Proper aggregate shape is important for workability and strength in concrete and stability in granular bases.

Uploaded by

vino
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Faculty :

Faculty of Civil and Environmental Engineering


Department :
Department of Infrastructure and Geomatic Engineering
Title :
AGGREGATE SHAPE TEST
(FLAKINESS INDEX & ELONGATION INDEX)
1.0 INTRODUCTION
The particle shape of aggregates is determined by the percentages of flaky and elongation
particles. Flaky and elongation particles are considered undesirable as they cause weakness
of the pavement. Rounded aggregates are preferred in cement concrete pavements as the
workability of concrete improves. Regular shapes of particles are desirable for granular
base course due to increased stability desired from better interlocking. When the shape of
aggregates deviates more from the spherical shape, as in the case of angular, flaky and
elongation aggregate the void content increase and hence the grain size distribution of the
aggregates has to be suitable altered in order to obtain minimum voids in the dry mix on the
maximum density.

2.0 OBJECTIVE
To determine the flakiness and elongation indices of the given aggregate sample.

3.0 FLAKINESS INDEX


Aggregate particles are classified as flaky when they have a thickness (smallest dimension)
of less than 0.6 of their mean sieve size. The flakiness index of an aggregate sample is
found by separating the flaky particles and expressing their mass as a percentage of the
mass of the sample tested. This test is not applicable to aggregate passing 6.30mm sieve and
retained as 63.0 mm sieve.

Faculty :
Faculty of Civil and Environmental Engineering
Department :
Department of Infrastructure and Geomatic Engineering
Title :
AGGREGATE SHAPE TEST
(FLAKINESS INDEX & ELONGATION INDEX)
3.1 Apparatus
1. Metal thickness gauge (Figure 1.0)
2. Test sieve, balance, trays, etc.

Figure 1.0 Shape Test Apparatus


3.2 Procedure
1. The sieve sample with sieves mentioned in Table 7.1. Weight each of the
individual size fraction (w1, w2, w3..)retained on these sieve, other than the
63.0 mm sieve and store them in separate trays marked with their size.
2. Gauge each fraction from the respective slots in the thickness gauge weigh
pieces which pass through the slots (x1, x2, x3..etc).

3.3 Calculations and Results.


Flakiness index = x1 + x2 + x3 + .

x 100

w1 + w2 + w3 + .

Where x1, x2,etc. are the weight of the fractions passing from the thickness gauge.
w1, w2etc are the weight of the original sample retained as the corresponding sieve

Faculty :
Faculty of Civil and Environmental Engineering
Department :
Department of Infrastructure and Geomatic Engineering
Title :
AGGREGATE SHAPE TEST
(FLAKINESS INDEX & ELONGATION INDEX)
4.0 ELONGATION INDEX
Aggregate particles are classified as elongation when they have a length (greatest
dimension) of more than 1.8 of their mean sieve size. The elongation index is found by
separating the elongation particles and expressing their mess as a percentage of the mass of
sample tested. The test is not applicable to material passing 6.30 mm sieve or retained on
50 mm sieve.
4.1 Apparatus
1.
Metal length gauge
2.

Sieve

3.

Balance

4.

Tray

4.2 Procedure
1.

Sieve the sample with sieve mentioned in table (3) weight each of the individual
size fractions (w1, w2, w3. Retained on these sieves other than the 50.0 mm
sieve.

2.

Gauge each fraction as follows, select the length gauge appropriate to the single
fraction under test and gauge each particle separately by hand. Elongated
particles are those whose greatest dimension prevent them from passing through
the gauge. Weigh each fraction which doesnt pass through the gauge (y1, y2,
etc)

4.3 Calculation and Results


Elongation index = x1 + x2 + x3 + .

x 100

w1 + w2 + w3 + .

Where: y1, y2, y3, .weight of the fractions not passing through the length gauge
w1, w2, w3,.are the weight of the original sample on the corresponding sieve.
3

Faculty :
Faculty of Civil and Environmental Engineering
Department :
Department of Infrastructure and Geomatic Engineering
Title :
AGGREGATE SHAPE TEST
(FLAKINESS INDEX & ELONGATION INDEX)
Aggregate Shape Test
Size of aggregate
Passing through
IS sieve, mm

Retained on
IS sieve, mm

Width of the
friction
contesting of at
last 200 piece, g

1
63
50
37.5
28
20
14
10
Total

2
50
37.5
28
20
14
10
6.3

3
W1mm.
W2mm.
W3mm.
W4mm.
W5mm.
W6mm.
W7mm.

Flakiness index

x1 + x2 + x3 + .

Weight on
aggregate in each
fraction passing
thickness gauge,
g
4
X1mm.
X2mm.
X3mm.
X4mm.
X5mm.
X6mm.
X7mm.

x 100

w1 + w2 + w3 + .

Elongation index =

x1 + x2 + x3 + .
w1 + w2 + w3 + .

x 100

Weight on
aggregate in
each fraction
retained on length
gauge, g
5
Y1mm.
Y2mm.
Y3mm.
Y4mm.
Y5mm.
Y6mm.
Y7mm.

Faculty :
Faculty of Civil and Environmental Engineering
Department :
Department of Infrastructure and Geomatic Engineering
Title :
AGGREGATE SHAPE TEST
(FLAKINESS INDEX & ELONGATION INDEX)
Table 2 data for Determination of Flakiness Index
Aggregate Size Fraction
Width of slot in
Minimum mass for
thickness
Gauge
or
subdivision
BS test sieve nominal aperture size
special sieve
100% passing
100% retained
mm
mm
mm
kg
63.0
50.0
33.9 0.3
50
50.0
37.5
26.3 0.3
35
37.5
28.0
19.7 0.3
15
28.0
20.0
14.4 0.15
5
20.0
14.0
10.2 0.15
2
14.0
10.0
7.2 0.1
1
10.0
6.3
4.9 0.1
0.5
This dimension is equal to 0.6 times the mean test sieve size
Table 3 data for Determination of Elongation Index
Aggregate Size Fraction
Width of slot in
Minimum mass for
thickness Gauge or
subdivision
BS test sieve nominal aperture size
special
sieve
100% passing
100% retained
mm
mm
mm
kg
50.0
37.5
78.7 0.3
35
37.5
28.0
59.0 0.3
15
28.0
20.0
43.2 0.15
5
20.0
14.0
30.6 0.15
2
14.0
10.0
21.6 0.2
1
10.0
6.3
14.7 0.2
0.5
This dimension is equal to 1.8 times the mean test size.
REFERENCES
British Standards Methods of determination of particle shape BS 812, Part 105, 1989.
Kenneth N. derucher and George P .Korfiatis, Material for civil and highway engineers, Prentice
Hall, NJ 2nd edition, 1988.
Harold N. Attkins, Highway materials, soils and concretes, 3rd edition, Prentice Hall, 1990.
5

Faculty :
Faculty of Civil and Environmental Engineering
Department :
Department of Infrastructure and Geomatic Engineering
Title :
AGGREGATE SHAPE TEST
(FLAKINESS INDEX & ELONGATION INDEX)
5.0 RESULT & ANALYSIS

Summary of Flakiness & Elongation Index Test (BS 812 Part: III)

Passing
Sieve
(mm)
63

Retained
Sieve
(mm)

Sample
(gm)

Passing
(gm)

Retained
(gm)

Flakiness
Index

Elongation
Index

50
37.5
28
20
14
10

Checked by ; ..

Date :..

Faculty :
Faculty of Civil and Environmental Engineering
Department :
Department of Infrastructure and Geomatic Engineering
Title :
AGGREGATE SHAPE TEST
(FLAKINESS INDEX & ELONGATION INDEX)
6.0 DISCUSSION
a) Determine wheather the aggregate tasted meets Malaysian standard requirement

7.0 CONCLUSION

You might also like