Scribd
Upload
350 views

Electrical Power Distribution Specification-II

Electrical distribution specification part-II describes the code and standards for electrical distribution

Uploaded by

ssb
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
350 views

Electrical Power Distribution Specification-II

Electrical distribution specification part-II describes the code and standards for electrical distribution

Uploaded by

ssb
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

SPECIFICATIONS FOR ELECTRICAL WORKS

1.0 GENERAL
To provide a complete electrical system for the distribution of electric power
from the point of supply D.G.s to the utilization equipment, and described in
these specifications. It will be the bidders responsibility to work out the exact
quantities with drawings as per area program & from work site, which trade
provides said equipments, materials, tools and labour.
2.0 SCOPE
The bidder shall supply, install and commission along with requisite spare,
maintenance tools and tackles the following equipments and system in the
Building. The scope also covers the detailed engineering and calculations of the
various equipments/system mentioned hereunder and the same shall be
approved by the Owner /Architect prior to execution of the job.
1. 11 KV H.T. Switchboards.
2. Specification of Distribution Transformers
3. Specification of L.T panels and switchgears.
4. Specification for Lighting Protection system.
5. Specification for Capacitor Bank and Capacitor Control Panels.
6. A) Specification of HT cable (XLPE) (11KV)
B) Specification of LT cables and Wire
7. Specification for Internal Electrical Works.
8. Specification for wiring.
9. Specification for D.G Set.
10. Specification for Intelligent Reporting Fire Detection System
11. Specification for PA System
12. Surveillance Closed Circuit Television (CCTV) System.
13. Specification for Conduiting And Wiring for Telephone System.
14. Specification for Nurse Call System.
15. Specification of Heat Ventilation & Air Conditioning System.
16. Specification of Signage.
17. Specification of Lift.
18. Specification of Pump Motor for Water Supply & Sweage. .
19. Specification of Mortuary Cooler.
20. Solar System
21. U.P.S System
22. Special Condition.
23. List of Approved Make.

This specification defines the basic guidelines to develop a suitable electrical


system as necessary for the hospital complex. All data required in this regard
shall be taken into consideration to develop a detailed engineering of the
system.
Compliance with these specifications and/or approval of any of the
Contractors documents shall in no case relieve the Contractor of his
contractual obligations.
All work to be performed and supplies shall be affected as a part of contract
requires specific approval/review of Owner or his authorised representative.
Major activities requiring approval/review shall include but not be limited to
the following:
The engineering activities shall comprise the submission for approval of the
following:
Basic engineering documents e.g. overall single line diagram, area
classification drawing, overall cable layout, testing, type test report,
guaranteed particulars of all equipments and maintenance manuals.
Quality assurance procedures.
Field testing and commissioning procedures.
Control and protection schemes.
Load sharing and annunciation scheme,
Preparation of power supply distribution drawing.
Bidder shall be responsible for:
Detailed co-ordination with other services, shop drawings for various
electrical layouts such as equipment layout, lighting layouts, cabling layouts,
earthing and lightning protection layouts, including equipment installation and
cable termination details etc. prior to start of work.
Preparation of bill of materials for cabling, lighting, earthing and
miscellaneous items etc.
Cable schedule.

Lighting/power panel schedule.


Interconnection drawing.
Protection co-ordination drawings/tables for complete power system.
Shop inspection and testing procedures.
Field testing and commissioning procedures.
Preparation of as built drawings for all services.
Bidder shall also be responsible for:
Any other work/activity which is not listed above however is necessary for
completeness of electrical system.
3.0 CODES & STANDARDS
The design engineering manufacturing and the installation shall be in
accordance with established codes, sound engineering, practices, and
specifications and shall conform to the statutory regulations applicable in the
country. Contractor shall obtain all approvals from statutory authorities e.g.
Electrical inspector, pollution control boards, WBSEDCL /CESC as applicable
before commissioning of electrical/DGs.
Indian Electricity Act.
Indian Electricity Rules.
Factory Act.
Pollution Control Act.
IS-732 : Code of practice for electrical wiring installation system voltage not
exceeding 650V.
IS-3043 : Earthing.
IS-2309 : Code of practice for the protection of buildings and allied structure
against Lightning
IS-7689 : Guide for control of undesirable static electricity.
IS-3716 : Insulation co-ordination application guide.
IS-8130 : Conductors for insulated electrical cables and flexible cords.
IS-5831 : PVC insulation and sheath of electric cables.
IS-3975 : Mild steel wire, strips & tapes for armouring cable.
IS-3961 : Current rating of cables
IS-694 : PVC insulated (heavy duty) electric cables for working. Voltage up to
and including 1100 volts.
IS-424- 1475 (F-3) : Power cable flexibility test.
IEC-439/IS-7098 : Specification for cross linked polyethylene insulated PVC
sheathed cable for working voltage up to 1.1 KV.

IS-1554 : PVC insulated cables up to 1100 volts.


IS-10810: Test procedures for cables.
IS-6121: Cable glands.
IS-10418: Cable drums.
IEC-754(1) : FRLS PVC insulated cable.
ASTM-D-2863 : Standard method for measuring minimum oxygen
concentration to support candle-like combustion of plastic (oxygen index).
ASTM-D-2843 : Standard test method for measuring the density of smoke from
burning or decomposition.
ASTM E-662/IEC 754(A)
Standard test method for specific optical density of smoke generated by solid
materials.
IEEE-383: Standard for type test class-IE, electric cables, field splicers and
connections for power generation station.
IS 13947/IEC 947 : Air circuit breaker/moulded case circuit breaker.
IS-8623: Specification for factory built assemblies of switch gear and control
gear for voltage upto and including 1000vac/1200vdc
IS 1018: Switchgear and control gear selection/installation and maintenance
IS-1248 :Direct acting indicating analogue electrical measuring instruments and
testing accessories.
IS-13779: Digital measuring instruments and testing accessories.
IS-3156 : Voltage transformer
IS-2705: Current transformer for metering and protection with classification
burden and insulation.
-IS -2147 : Degree of protection provided by enclosures for low voltage.
PART 1,11,111 Switchgear and control gear
IS-3427 : Metal enclosed switchgear and controlgear
BS-162 : Safety clearance
IS-3202 : Code of practise for climate proofing of electrical equipment.
IS-375 : Marking and arrangement for switchgear, busbars, main connections
and auxiliary wiring.
IS-722 : Ac electric meters
IS-3231 : Electrical relays for power system protection.

IEC-255
IS-5082 : Electrolytic copper/aluminium bus bars
IS-2834 : Capacitors
IS-2713 : Steel tubular pole
IS-335 : Specification for insulating oil
IS-3837 : Specifications for accessories for rigid steel conduit for electrical
wiring.
IS-2026&335 : Distribution transformer
(PART I,II,III)GI/STEEL /PVC conduit pipe for electrical wiring.
IS-2274 : Code of practise for electrical wiring installation system voltages
exceeding
650 volts.
IS-6665 : Code of practise for industrial lighting
IS-3646 : Interior insulation part 1&2
IS-1944 : Code of practise for lighting of public through fares.
IS-7752 : Guide for improvement of power factor consumers installation.
IS-13346 : General requirement for electrical for explosive gas atmosphere.
IS-13408 : Code of practise for the selection, installation and maintenance of
electrical apparatus for use in potentially explosive atmospheres
IS-12360 : Voltage and frequency for ac transmission & distribution system.
IS-5572 : Classification of hazardous area for electrical installations.
IS-5571 : Guide for selection of electrical equipment for hazardous area.
IS-4201 : Application guide for Current Transformer
IS-4146 : Application guide for Voltage Transformer
IS-10028: Code of practise for installation and maintenance of transformer
IS-8478 : Application guide for on load tap changer
IS-10561: Application guide for power transformer
IS-1646 : Code of practise for fire safety of buildings electrical installation
IS-3034 : Code of practise for fire safety of industrial building-electrical
generating and distribution station
IP-30 : National electrical code (NEC) BIS publication.
IS-4722 : Rotating electrical machines.
IS-4889 : Method of determination of efficiency of rotating electrical machines.
IS-325 : Three phase induction motors.
IS-4729 : Measurement and evaluation of vibration of rotating electrical
machines.
IS-900 : Installation and maintenance of induction motors.
IS-4029 : Air break switches.
IS-2208-9224 : HRC cartridge fuses.
IS-2959 : Contactors.

IS-9537 : Rigid steel conduit.


IS-1030-1982 : Specification for carbon steel castings for general engineering
purpose.
IS-1601/ BS-649 : Performance& testing of Internal Combustion (IC) engines for
general purpose.
AIEE-606(1959) : Recommended specification for speed governing of I.C.
engine generator units.
BS-5514/IS-3046 8528(Part-2): Reciprocating IC engine driven A.C. generators.
Any other standard may be followed provided it is equivalent or more
stringent than the standards specified above.
In case of any deviation /conflict of this specification with the codes &
standards, the following order of precedence shall govern.
a) Specification, particular specification if any, and drawings.
b) Indian

You might also like