Acc Accelerator Control System
Uploaded by
UALU333Acc Accelerator Control System
Uploaded by
UALU333ENGINE
SECTION
ACC
ACCELERATOR CONTROL SYSTEM
ACC
CONTENTS
PRECAUTION ............................................... 2
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................... 2
REMOVAL AND INSTALLATION ................ 3
ACCELERATOR PEDAL ASSEMBLY ............... 3
Removal and Installation .......................................... 3
Inspection ................................................................. 3
SERVICE DATA AND SPECIFICATIONS
(SDS) ............................................................. 5
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................. 5
Accelerator Control ................................................... 5
Exploded View .......................................................... 3
Revision: August 2014
ACC-1
2015 Rogue NAM
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011280339
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Revision: August 2014
ACC-2
2015 Rogue NAM
ACCELERATOR PEDAL ASSEMBLY
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
ACCELERATOR PEDAL ASSEMBLY
Exploded View
INFOID:0000000011280340
ACC
AWBIA1974ZZ
1.
Brake pedal
B. Locator pin
2.
Accelerator pedal assembly
C.
Bolt
A. Locator hook
Removal and Installation
INFOID:0000000011280341
REMOVAL
1.
2.
Disconnect the harness connector from the accelerator pedal assembly.
Remove the bolts, then remove accelerator pedal assembly.
CAUTION:
Do not disassemble accelerator pedal assembly.
Do not drop or impact accelerator pedal assembly.
Do not expose accelerator pedal assembly to water.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
When installing the accelerator pedal assembly, make sure to align locator hook and locator pin before installing bolts.
For inspection, refer to ACC-3, "Inspection".
Inspection
INFOID:0000000011280342
INSPECTION AFTER INSTALLATION
Revision: August 2014
ACC-3
2015 Rogue NAM
ACCELERATOR PEDAL ASSEMBLY
< REMOVAL AND INSTALLATION >
Check that the accelerator pedal moves smoothly within the specified range.
Accelerator pedal stroke (A)
: Refer to ACC-5, "Accelerator Control"
Check the accelerator pedal height.
Accelerator pedal height (B)
: Refer to ACC-5, "Accelerator Control"
AWBIA1744ZZ
If accelerator pedal does not meet specified values, check brake pedal height. Refer to ACC-3, "Inspection".
Depress and release the accelerator pedal to check that it returns quickly and smoothly to the original
released position.
CAUTION:
Whenever the harness connector of the accelerator pedal position sensor has been disconnected,
perform "Accelerator Pedal Released Position Learning". Refer to EC-142, "Work Procedure".
The accelerator pedal should operate smoothly without catching when the pedal operating force is
released. The pedal should return smoothly to the fully raised position. The spring should be free
from damage.
Revision: August 2014
ACC-4
2015 Rogue NAM
SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Accelerator Control
INFOID:0000000011280343
ACC
Unit: mm (in)
AWBIA1744ZZ
Accelerator pedal stroke (A)
49.6 - 52.4 (1.95 - 2.06)
Pedal height difference between accelerator and brake (B)
35 - 45 (1.38 - 1.77)
Revision: August 2014
ACC-5
