Scribd
Upload
247 views

ACP Tutorial Ex1

This tutorial demonstrates the basic composite modeling workflow in ANSYS from defining materials to results visualization. It shows how to build a simple sandwich panel with layered composite materials, apply boundary conditions and pressure loading, then analyze and post-process the results.

Uploaded by

mehrdadwbor
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
247 views

ACP Tutorial Ex1

This tutorial demonstrates the basic composite modeling workflow in ANSYS from defining materials to results visualization. It shows how to build a simple sandwich panel with layered composite materials, apply boundary conditions and pressure loading, then analyze and post-process the results.

Uploaded by

mehrdadwbor
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 34

ANSYS Composite PrepPost 16

Tutorial Exercise 1

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial
Goals:

Basic composite workflow from a geometry to post-processing.


Build a simple sandwich panel.
Load case: Clamped panel under uniform pressure.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Open a new Workbench project and restore the archive


tutorial_1.wbpz.

Review the boundary conditions, and verify that the model is welldefined with the default material. Review the results with an
isotropic material.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Add the ACP (Pre) component to the existing analysis.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial
First composite materials have to be defined in ANSYS Workbench
Engineering Data:
There are two possibilities:

1. Import preconfigured materials from the Composite Materials catalog


(see figure below)
2. Create new materials
In this example, you will create new materials as shown in the following
slides.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial
Define a unidirectional
material in ANSYS
Workbench Engineering
Data with the following
properties:

Hint
Uncheck the filter button to display
all properties in the toolbox

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial
Define also a core material:

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Update Model and then refresh Setup in the ACP (Pre) component:

Open Setup of ACP (Pre) with a double-click on Setup (or Edit in


drop-down menu )

1
8

2013 ANSYS, Inc.

3
ANSYS, Inc. Proprietary

ACP Tutorial

In ACP further material data (Fabrics,


Stackup and Sublaminates) have to be
defined.

Define a new Fabric with the defined


materials:
Carbon UD with 0.2 mm thickness,
Foam core with 15 mm thickness.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

10

Define a new Stackup with the UD Carbon. A Stackup is a preassembled tape also called non-crimp fabric (NCF).

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Review the Biax properties through the Plot tab.

Click on apply to update the model


& OK to close the window.

11

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

12

Define a Sub Laminate as shown below and plot the mechanical


properties.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

13

Define a new Rosette (using the default settings):

After the material definition the orientations and offset directions


have to be defined. This is done with Oriented Element Sets which
are defined now.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Define a new Oriented Selection Set (OSS):


Click on an
element of the
model.

2
3
(1) Click in the Element Sets box in the
dialog box
(2) Select the desired Element Set in
the tree

4
5

14

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial
(1) The Orientation Point and Direction specify the offset direction.
Toggle the
button in the toolbar and select the OSS to check the offset
direction.
(2) The rosette of an OSS defines the material reference (0) direction.
Toggle the
button to visualize the reference direction.
(Click Update button if no orientation is displayed.)

The OSS is now used to define the layup. The offset direction of the OSS
and the order of the Modeling Plies define the stacking sequence, the
reference direction and the relative angle of the modeling plies specify
the fiber alignment.
15

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

16

Define 3 Ply Groups:

Create the first Modeling Ply:

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial
1.

Configure the first ply:

1
2 : select in the tree
3: select ply from the list
4: Angle 0 (default)
5

17

2.

Define a second ply in the sandwich_core Modeling Group with


the Fabric Core and a Ply angle of 0.

3.

Define a third ply in the sandwich_top Modeling Group with the


Fabric Carbon T700_UD and a Ply angle of 90. Set Number of Layers
to 3.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Update the model:

The ply definition should look like this:

18

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Return to ANSYS Project Schematic.


Update the ACP (Pre) Setup.
Refresh the Section Data.
Update the whole project

2
1

19

Updating directly the whole project is also possible.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Add ACP (Post) System

Update ACP (Post) Results

Open Results of ACP (Post) by double-clicking on the cell

20

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Add a ACP (Post) System to the project


Add by dragging the ACP (Post) over ACP (Pre) System

21

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Connect the solution with the ACP (Post)


Drag the Static Structural Solution cell over the ACP (Post) Results cell
Update the project
Enter ACP (Post) by double clicking on the cell

22

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial
The Solution is already imported from the *.rst file.

23

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Create a plot to visualize the deformations:


Insert a deformation plot under the solution
Set the deformation scale in the in the toolbar

24

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

25

Toggle element edges and surface in the toolbar.

View deformation results

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

26

In the next step a combined Failure Criteria is configured to create an


overall failure plot of the composite structure.

For the 2 materials, the stress limits were defined in the Engineering
Data at the beginning of this tutorial.

Definitions: Create a Failure Criteria.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

27

Chose the following failure criteria to define a combined failure


criteria definition

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Insert a failure plot under the solution

Activate checkboxes for critical layer


and critical layer

1
28

2013 ANSYS, Inc.

2
ANSYS, Inc. Proprietary

ACP Tutorial
Remove the deformation scale from the solution.
Update the model to see the overall failure plot:

The contour plot shows the maximum inverse reserve factor of each element

29

(through all layers, all selected failure criteria and integration points)
The text plot indicates the critical layer and the critical failure mode.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

Sampling points and ply-wise plots can be used to investigate the


results in more detail.

Create a Sampling Point and select the element of interest.

Select the element of


interest.
30

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

31

Insert a ply-wise stress plot for the transverse stresses s2

Ply-wise plots only show results when a ply is selected.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

32

Select the Analysis Plies of the Sampling Point to visualize the stress
distribution of a single ply.

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

ACP Tutorial

33

The through-the-thickness distribution of strains, stresses or failure


results can be visualized in the Analysis tab of the Sampling Point.

Change to the Analysis Tab of the Sampling Point to configure the


through-the-thickness post-processing plot:

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

End of Tutorial 1
Thank you

34

2013 ANSYS, Inc.

ANSYS, Inc. Proprietary

You might also like