VB Scripting

for CATIA V5
How to Program CATIA Macros

Emmett Ross
Fourth Edition

Copyright Information
VB Scripting for CATIA V5: Fourth Edition. Revised September 2014.
Copyright 2014 by Emmett Ross

All rights reserved. No part of this book may be reproduced or transmitted in any form or by
any means, electronic or mechanical, including photocopying, recording, or by any
information storage and retrieval system, without permission in writing by the author. The
only exception is by a reviewer, who may quote short excerpts in a review. CATIA is a
registered trademark of Dassault Systmes. No affiliation with, or endorsed by anyone
associated, or in any way connected with Dassault Systmes, Microsoft Corporation, UNIX,
or any of their fantastic products. We recognize that some words, model names and
designations, for example, mentioned herein are the property of the trademark owner. We
use them for identification purposes only. This is not an official publication.

Disclaimer

Although the author has attempted to exhaustively research all sources to ensure the
accuracy and completeness of information on the subject matter, the author assumes no
responsibility for errors, inaccuracies, omissions, or any other inconsistencies herein. The
data contained herein is for informational purposes only and is not represented to be error
free. Information may be rendered inaccurate by changes made to the subject of the material,
such as the applicable software. No consequential damages can be sought against the author
for the use of these materials by any third parties or for any direct or indirect result of that
use. The purpose of this text is to complement and supplement other texts and resources.
You are urged to read all the available literature, learn as much as you can and adapt the
information to your particular needs. There may be mistakes within this manual.
Therefore, the text should only be used as a general and introductory guide and not as the
sole source for CATIA macro programming. The information contained herein is intended
to be of general interest to you and is provided as is, and it does not address the
circumstances of any particular individual or entity. Nothing herein constitutes
professional advice, nor does it constitute a comprehensive or complete statement of the
issues discussed thereto. Readers should also be aware that internet websites listed in this
work may have changed or disappeared between when this work was written and when it
is read.
The author also assumes a general understanding of how to use CATIA V5 including
geometry creation and various workbenches (mainly Part Design, Generative Shape Design,
and Assembly Design). To learn more about CATIA please refer to the resources in the
Appendix for more information about how to use CATIA or where to go to get further
answers or advice. I welcome any comments you may have regarding this book. To contact
me please email: [email protected]

The Authors Story

Learning how to program CATIA macros helped save my career.
Youve probably found your way to this book from my website, or maybe a friend passed it
along to you. Either way, Im happy youre here. I wrote this guide because when I was in a
time of desperate need, not too long ago, learning how to write CATIA macros helped save
my professional career. I was working as a CAD engineer but was just beginning to learn
how to use CATIA. Everyone else at my company was much more experienced than I was,
therefore I was expendable. When the economy took a turn for the worse, and coworkers
began getting laid off, I feared for my job and my familys future.

I needed a way to set myself apart to prove my value to the team. Learning how to write
macros in CATIA gave me a huge advantage over my coworkers and helped to quickly earn
my colleague's respect, leading not only to me keeping the job but also to quicker
promotions, along with more job freedom and flexibility. Not only did it help me bounce
back from a low point but it opened my eyes to the world of automation and the
opportunities that it can create for an engineers career. Scripting4v5.com and VB Scripting
for CATIA V5 are my way of giving back for all of the fortunate things that have happened to
me ever since.
I want this content to provide anyone walking in off the street the knowledge to be able
to write their first CATIA macro with as little pain as possible. This book is a guide, and the
purpose of this guide is to do just that - guide you. It will take you through the process of
turning your ideas into automated programs. If I can help just one person learn one thing
that will help them in their career and/or life, the countless hours I have spent writing this
book will have been totally worth it. If at any point while youre reading this guide and you
have any questions, please dont hesitate to contact me. Even if you dont have any
questions, Id love for you to come by and say hello! If you want to reach me in private you
can email me at [email protected].

-Emmett Ross

Chapter 1: Introduction to CATIA Programming

Are you tired of repeating those same time-consuming CATIA processes over and over?
Worn out by thousands of mouse clicks? Dont you wish there were a better way to do
things? What if you could rid yourself those hundreds of headaches by teaching yourself
how to program macros while impressing your bosses and coworkers in the process? VB
Scripting for CATIA V5 is the ultimate guide to teach you how to write macros for CATIA
V5!

Through a series of example codes and tutorials youll learn how to unleash the full power
and potential of CATIA V5. No programming experience is required! There are many CAD
engineers, designers, and technicians who want to write macros but simply don't have the
time or money to go to an expensive third party training class. This text will cover the core
items to help teach beginners important concepts needed to create custom CATIA macros.
More importantly, youll learn how to solve problems and what to do when you get stuck.
Once you begin to see the patterns youll be flying along on your own in no time.

Book Format
Everyone learns in different ways. Therefore, VB Scripting for CATIA V5 is comprised of
different types of exercises in order to address all the different learning styles.

Tutorials: Step-by-step instructions will show you exactly how to create the example
macros.
Exercises: Basic steps and an end goal of a problem are given and the programmer
must figure out the best way to solve it. Solutions in the back of the book.
Quizzes: The end of each chapter features a quiz between 5 and 15 questions
comprising multiple choice, fill in the blank, or true or false questions to test your
knowledge The solutions are located in the back of the book.
Real-world examples: Where possible I will show you how the code can be applied
in the real-world of CAD engineering.

What is a Macro and why do we use them?

A macro is a series of functions written in a programming language that is grouped in a

single command to perform the requested task automatically. If you perform a task
repeatedly you can take advantage of a macro to automate the task. Why do manual labor

when you can simply press a button instead? Macros are used to save time and reduce the
possibility of human error by automating repetitive processes. Other advantages include
standardization, improving efficiency, expanding CATIA's capabilities, and streamlining
procedures. Macros use programming but you don't need to be a programmer or have
programming knowledge to use them (though it certainly does help).

The application of automation in the design process is virtually unlimited. Some real world
examples of CATIA automation at work:

Batch script for the conversion of CATDrawing files to PDF

Batch script to convert CATParts to STP files
Import of points from an Excel spreadsheet to a 3D CAD model
Export of data from CATIA model to a bill of material spreadsheet
Automatic geometry creation from selection
Automatic drawing creation
Custom functions

And so on and so on. The possibilities are nearly limitless.

Terms and Definitions

The following is a list of terms and their definitions which will be used frequently
throughout this text. It is recommended that you become familiar with them if you arent
already. A quick reference of acronyms is listed in the appendices of this book as well.

Integrated Development Environment (IDE) is a computer application to help

programmers develop software and typically consists of a source code editor, debugger,
build automation tools, object browser, and a compiler or interpreter. IDEs typically have
built-in syntax checkers, color coded schemes, and automatic code completion. The Visual
Basic Editor in CATIA and Excel is an example of an IDE.

Graphical User Interface (GUI) is a way for humans to interact with computers with
graphical elements such as windows, menus, toolbars, icons, etc. which can be manipulated
by a mouse. The VBA editor is a perfect example.
Command Line Interface (CLI) is a way for humans to interact with computers through
text only and is accessed solely by a keyboard. The most common example is MS-DOS.

Component Application Architecture (CAA, CAA V5, or CNext) is the Application

Programming Interface (API) or technological infrastructure designed to support
Dassault Systmes products. It is an open development platform enabling programmers to
develop and integrate their own applications for CATIA or other Dassault Systmes
products. CAA V5 is faster and more powerful than VB. It provides access to interfaces not
available to Visual Basic but is harder to learn. C++ is the primary language. A single source
code is used for both Windows and UNIX. CAA Rapid Application Development

Environment (RADE) provides a workbench to develop PLM applications using the

component object model object oriented programming. CAA is beyond the current scope of
this text.

Object Oriented Programming (OOP) is where programmers define not only the data
type of a data structure, but also the types of operations, or functions, that can be applied to
the data structure. An object in software is a structure that consists of data fields and
subroutines or functions. Everything in CATIA is an object; the data fields are called
Properties and the subroutines and functions are called Methods. All the data and functions
have owners which are the objects to which they belong. A thorough understanding of OOP
is critical to your success in macro programming. More on this later.

Component Object Model (COM) is a Microsoft technology that enables sharing of binary
code across different applications and languages. CATIA V5 is COM enabled software. Codes
for COM objects or components can be called, initiated, or created at any time because they
are stored in DLL files and registered in the Windows registry. If CATIA calls Excel, CATIA is
then the client and Excel is the server, or the one that provides services to the client.

VB talks to CATIA through Dynamic Linked Libraries (DLL). DLLs are compiled files that
contain all of the functions that make CATIA V5 perform an action. For example, when you
select the point function in CATIA, the program calls a function inside one of the dll files
that performs the action of creating a point in the V5 database. These files are both
compiled and encrypted (or mangled) and are located in the UNLOAD directory for CATIA
V5 (C:\Program Files\Dassault Systemes\B20\intel_1\code\bin). Encryption is a method by
which software companies can ensure that others cannot access the function inside the dlls.
You cannot directly call the dlls from outside applications, therefore extra programming
needs to be done to allow the dlls to be exposed to Windows and the COM object model.
This is done via Type Library Files.
Type Library Files (TLB) are files necessary for exposing functions to Windows by acting
as maps which point to the functions inside of the dll files that make CATIA V5 work. The
TLB files are also located in the UNLOAD directory for V5. Any external application needs
to have access to these files. The complete process is: VB Application -> Type Libraries ->
Dynamic Linked Libraries -> CNext. How to create references to type libraries is shown in
later chapters of this text.
Universal Unique Identifier (UUID) - Every CATPart and CATProduct contains a UUID.
Basically, CATIA identifies files based on their file name and their UUID. Where problems
occur are when two pieces of data have the same UUID. Compounding the problem, the
UUID cant be viewed or edited with any current CATIA function. There are cases when two
files may have different names but share the same UUID. This causes a problem when
dealing with Product Data Management (PDM) systems, like SmartTeam. It is
recommended to create new UUIDs whenever possible. Actions which will create new
UUID include:

File + New
File + New From
File + SaveAs - option save as new document
INSERT New Product
INSERT New Part
Document Template Creation

Actions which will keep the same UUID for each include:

File + Open
File + Save Management
File + Save
File + SaveAs
Send to directory
File + CLOSE
File + Save
File + Save ALL

CATIA Macro Languages

Just like most countries on this planet have their own native languages, software programs
have their own programming language. Many of these are very similar to each other so
learning elements that are common between all programming languages will help you
transition from one to another if you need to! For example, after learning to program in
CATIA and Excel, I was able (with some help from some tutorials on YouTube) figure out
how to program some basic Android applications in Java. Thats powerful stuff!

CATIA V5 automation was originally designed for VB6, VBA, and VBScript. Microsoft no
longer officially supports VB6 as it has been replaced by VB.net, which is supported by
CATIA V5 R16 and onwards. VB6 is more complex but also more powerful than VBA, as is
VBA over VBScript and CATScript. Macro languages supported by CATIA and discussed in
this text are VBScript, CATScript, and VBA, all derivatives of Visual Basic used in scripting.

CATScript is Dassault Systmes portable version of VBScript and is very similar to it.
CATScript macros CAN run on UNIX systems. It is a sequential programming language and
non-GUI oriented. Regular text editors (like Notepad) can be used for coding. Advantages of
writing CATScript macros include free to use, macro recording, personal time saving
operations, and rapid deployment. The disadvantages of CATScript are limited flexibility
and difficult to debug. The file extension is .CATScript.

VBScript is a subset of the Visual Basic Programming language (VBA). All elements of
VBScript are present in VBA, but some VBA elements are not implemented in VBScript.
The result of the slimming down process is a very small language that is easy to use.
VBScript (officially, "Microsoft Visual Basic Scripting Edition") was originally designed to
run in Web applications such as Internet Explorer. One of the advantages of VBScript (in

common with other scripting languages) is that it's written in plain, ordinary ASCII text.
That means that your 'development environment' can be something as simple as Notepad.
CATIA objects can be called but no type is used as the system tries to dynamically call
methods and properties of objects. It can be used on both Windows and UNIX versions of
CATIA. The disadvantage of VBScript is its slow, is limited for interface development, and
has the least functionality. The file extension is .catvbs.
VBScript (MS VBScript) and CATScript are very similar with the major difference being
variable declaration. Many programmers believe it is better to declare all variables As
String, As Integer, etc. to better keep track of each variable type.

Visual Basic (VB or VB6) is the full and complete version. Derived from BASIC, VB6
programs can generate independent programs, can create ActiveX and servers, and can be
compiled. VB programs run in their own memory space.

VBA (Visual Basic for Applications) is another subset of Visual Basic and is hosted in
applications such as CATIA (after V5R8), Microsoft Word, Excel, etc. VBA provides a
complete programming environment with an editor, debugger, and help object viewer.
Declaring the object library used is allowed. In CATIA, VBA has the full VB6 syntax and IDE,
which is similar to VBA in Excel. It is event driven, GUI oriented, and has full IDE yet cannot
run a program WITHOUT the host application running (meaning it runs as a DLL in the
same memory space as the host application). The advantages of using CATvba macros
include using the GUI, building forms, and the debugging ability of the macro editor. The
disadvantage is VBA programs cannot be compiled into executables or DLLs and they do
not run in their own memory space. The extension is .catvba.

Visual Basic.NET (VB.net) is Microsofts designated successor to VB6 and has been
supported by Dassault Systmes since V5R16. VB.net is event driven, has IDE, and is used
for building GUI but is not COM (though it can call COM objects). The syntax is different
from VB6. Code can be compiled into .exe or .asp files. There are many issues encountered
when switching from VB6 to VB.net, such as new syntax, new IDE, new GUI controls, and a
new Install Shield, therefore fully automatic conversions are near impossible. Compiled
languages like VB.net arent completely necessary because most automation can be done in
VBA. VB.net will not be discussed in this text.
There are two primary methods a macro communicates with CATIA: in-process or out of
process.

In Process: The first method a macro communicates with CATIA is when the VB
application is ran from within the CATIA process in the computer memory. CATIA
essentially freezes while the macro is running and the allocation memory is wiped clean
after each run of the program so passing data between subsequent runs is impossible. To
access and create in-process macros go to Tools > Macros but please note the only options
are VBScript, CATScript, or VBA. Most of the examples in this text are In Process macros.
Out of Process: The other communication method is called out of process where the
program runs in its own process in the computer memory. The application could be run

from Excel, Word, Windows Explorer, etc. CATIA is fully active while the program is
running. VB.net or VB6 can also be used.

How to Create Macros

Macros within CATIA are created by two primary methods:

1. Using the macro recorder or
2. Writing custom code with the macro editor

Once a macro is created, there are multiple ways to open the macros window to run your
macros:
1. Go to Tools>Macro>Macros
2. CATIA macros window keyboard shortcut: Alt+F8
3. Assign or create your own icon for each macro
4. Visual Basic Editor (VBE) shortcut: Alt+F11

If the macro editor cannot be opened, talk to your system administrator because it may
not have been installed. No extra license is required to run macros, though sometimes
licenses for special workbenches are needed if the code uses a function or method from a
particular workbench.

Macro Libraries

CATIA macros are stored in macro libraries in one of three locations: Folders (vbscript and
CATScript), Project files (catvba), or documents such as CATParts, CATProducts, and
CATDrawings. Only one of these macro libraries can be used at a time. When creating a new
macro library, the folder or path location must already exist. If not you will get an error
message.

Tutorial 1.1: Create a new macro library

Use the following steps to create a new macro library or setup an existing one:
1. Go to Tools>Macro>Macros

2. Click "Macro libraries"

3. Ensure the Library type is set to "Directories" then click "Create new library"

4. Type in the file location where you are planning on saving all of your CATIA
macros then click OK.

5. Close the macros libraries window. This is where you can create CATScript macros. If
you were setting up an existing library (add existing library versus Create new library) you
would see a list of .CATScript files here. You only need to do this once as the library should
load even after restarting CATIA.

CATIA Macro Syntax

Syntax is defined as the ordering of and relationship between the words and other
structural elements in phrases and sentences. You can think of it as a particular layout of
words and symbols. Each programming language is composed of its own syntax. Learning

the syntax of each programming language is crucial to creating successful macros. Think of
it like this: when you see an email address ([email protected]) you immediately
identify it as an email address. Why is this? An email address has a correct structure in the
language of the internet, its syntax. Syntax enables the programming language to
understand what it is you are trying to do. Listed below are some of the key syntax
features of CATIA macro programming:

Case Sensitivity: By default, VBA is not case sensitive and does not differentiate
between upper-case and lower-case spelling of words.
Comments: Add comments to your statements using an apostrophe ('), either at
the beginning of a separate line, or at the end of a statement. It is recommended
that you add comments wherever possible to make your scripts easier to
understand and maintain, especially if another user has to make changes to it later
on down the road.
Indentation: Indent or out dent script to reflect the logical structure and nesting of
the statements to make it easier to read.
Parentheses: It is important to use parentheses correctly in any statement to
achieve the desired result and to avoid errors.
Semicolon (:): Inserting a semicolon allows you to write multiple commands on the
same line of code.
Single Quotation(): To return a single quotation mark which does not indicate a
comment (needed in a formula for example), you'll have to use the Chr function.
Chr() is a built-in VBA function that returns the character that corresponds to the
numeric value of its argument using the ASCII coding scheme. If you provide Chr
with an integer value (such as 39) it will report back the character that corresponds
to that value. The ASCII value of 39 is the single quote mark. Chr(34) is for the
double quote mark. This is shown in an example later on in this text.
Spaces: Add extra blank spaces to your script to improve clarity. These spaces are
ignored by VBA.
Text Strings: When a value is entered as a text string you must add quotation marks
before and after the string. You can concatenate, or combine, multiple strings using a
plus (+) or ampersand (&) sign: txtString = This value is + TestValue. Return the
left, middle, or right of a string using: left(sting, digits), mid(string, digits), or
right(string, digits). Get the complete length of a string with len(string). To figure
out if a string contains another string use Instr(). Convert numeric strings and vice
versa using str(num) or val(string).
Underscore(_): Carry over to next line (line concatenation symbol).

Syntax is often the most frequent cause of a macro program not working and throwing an
error. There is a correct way to write your code. It takes practice, patience, and persistence
to understand but over time it will become second nature to you. If you follow the rules the
programming languages will understand you otherwise you will get errors.
Dealing with syntax can be tough which is why programmers have developed tools to help
create programs correctly. These are called IDE, or integrated development environments
(remember that definition defined earlier?). The Visual Basic editor in CATIA is the perfect

example (open it with Alt+F11). It contains a built-in syntax checker and works much like
a grammar checker found in software like Microsoft Word and will even give you hints
about what it thinks you meant.

Program Structure and Format

Macros in CATIA use sequential programming, meaning when you run your macro
program, the code will be read by the computer line by line, generally from top to bottom
and from left to right, just like reading a book. The program flows down the code until it
hits a decision point where it may have to jump to a different portion of the program or rerun lines of code that it already read. The program chooses what lines of code to execute
based on the state of the variables you have defined.

Macros can also be event driven meaning the execution of the program depends on an
event, such as a user clicking a button with the mouse, an object being selected, certain text
or characters being typed into a form, etc. One common decision point is an If...Else
statement. If the variable equals x then do y, else do z. Another one is the while loop which
will execute the lines of code within the loop over and over until the condition becomes
false. There are more examples of decision points and control structures but well get to
those later on in the text.

Its a good idea to maintain the same format and order on every single program you create.
Its very useful to keep your code clean and tidy, especially if other programmers are going
to work on it later. Remember; keep the code as simple as possible. Always try to use as
few lines of code as possible (which youll be glad you did when you have to troubleshoot
one of your macros). You can reduce the number of lines of code using a colon (:). A
common macro format may look something like this:
my name
date last revised
who the macro was created for
description of what the macro does
separatorMain code begins here, usually with Sub CATMain
define variables, constants, etc.
error handling
check if part or product is in design mode or not
update part, drawing, etc.
double check to make sure all loops are closed
End Sub

Macro Recording
One method for creating macros is by recording your mouse actions. For macros recorded
in a folder or in a CATPart or CATProduct, Dim statements (declarations) will be recorded
for CATScript but not for MSVBScript. For macros recorded in a .catvba library, "MS VBA" is
the only choice. Macros cannot be recorded while in the drafting workbench. A few things to
keep in mind when recording a macro:

DON'T: Switch workbenches while recording a macro.

DON'T: Record more than is absolutely necessary.
DON'T: Use the UNDO button when recording a macro.
DO: Be aware of CATSettings when recording.
DO: Exit sketches before stopping recording.
DO: Check each macro after it's recorded.

Always UNDO what you just recorded and run the macro (you are able to undo CATIA
macros after youve run them which is a good way to check if they work as expected or
not). If the macro works from within CATIA and repeats what you just did, then the macro
obviously works fine. If it does NOT work from within CATIA, you need to fix it. If it does
NOT work from within CATIA it will NOT work once you cut and paste it into a VB
application.

Look through the recorded macro. Many times extra lines of code are added which are not
necessary. This is based on the order of steps that you do as you record the macro. These
unnecessary lines can be removed. Recorded macros do not contain any comments or
explanations of what is happening in the code and input parameters are never recorded.

For example, if a macro is recorded to zoom in and then zoom out it might display the
following code:
Dim viewpoint3D As viewpoint3D
Set viewpoint3D = Viewer3D.viewpoint3D
Viewer3D.ZoomIn
Set viewpoint3D = Viewer3D.viewpoint3D
Viewer3D.ZoomOut
Set viewpoint3D = Viewer3D.viewpoint3D

Notice how the "Set Viewpoint" command appears multiple times? This is unnecessary in
this situation. The viewpoint only needs to be set once after the Dim statement (setting and
declaring will be explained in more detail soon).
Often times you might record a macro with a CATPart active and open it in its own
window. All goes smoothly and the macro replays fine. Then, the next day you replay the

macro again but this time you may have some other document type open or maybe a part
is open but it is in a product assembly. Usually, the macro will fail because when the code
was recorded a CATPart was the active document but now it is not. You need to add your
own error handling to the code to ensure this doesnt happen. This is one advantage to
writing custom code and knowing the fundamentals of CATIA macro programming.

Tutorial 1.2: Record a macro

In this tutorial youll record some actions then examine the recorded code.

1. Open a new CATPart. The name of the part doesnt matter.

2. Start recording a macro by going to: Tools > Macro > Start Recording.
3. Set the current macro library to the directory you setup in Tutorial #1. Choose
CATScript as the language used and give your macro a name, such as
FirstRecordedMacro.CATScript, then click start to begin recording your mouse
actions.

4. CATIA is now recording all of your actions. Create a plane, offset 20mm from the
default yz plane.

5. Click the Stop Recording button to stop recording the macro.

6. Click the Undo button to undo the plane creation macro you just recorded.
7. Alt+F8 to open the macros window. Select your FirstRecordedMacro code then click
Run. The macro should re-create a 20mm offset plane just as you did before.
8. If you open the macro window again but this time select edit, the code should look
something like this:

Language="VBSCRIPT"
Sub CATMain()
Dim partDocument1 As Document
Set partDocument1 = CATIA.ActiveDocument
Dim part1 As Part
Set part1 = partDocument1.Part
Dim hybridShapeFactory1 As Factory
Set hybridShapeFactory1 = part1.HybridShapeFactory
Dim originElements1 As OriginElements
Set originElements1 = part1.OriginElements
Dim hybridShapePlaneExplicit1 As AnyObject
Set hybridShapePlaneExplicit1 = originElements1.PlaneYZ
Dim reference1 As Reference
Set reference1 = part1.CreateReferenceFromObject(hybridShapePlaneExplicit1)
Dim hybridShapePlaneOffset1 As HybridShapePlaneOffset
Set hybridShapePlaneOffset1 = hybridShapeFactory1.AddNewPlaneOffset(reference1,
20.000000, False)
Dim hybridBodies1 As HybridBodies
Set hybridBodies1 = part1.HybridBodies
Dim hybridBody1 As HybridBody
Set hybridBody1 = hybridBodies1.Item("Geometrical Set.1")
hybridBody1.AppendHybridShape hybridShapePlaneOffset1
part1.InWorkObject = hybridShapePlaneOffset1
part1.Update
End Sub

Congratulations! Youve recorded your first macro. But what does all the code mean? How
do you make sense of it? Hopefully by the end of this book youll understand every line of
code and will be able to recreate the program without using the macro recorder.

CATIA Macro Variable Naming

Variables make up the backbone of any programming language. Basically, variables
store information that can be accessed later by referring to a name or variable. Lets
say you have an input box in your code where the user will enter a part number. You
refer to the input box as componentName. In other words, componentName is a symbolic
name, or word, for the input box, the variable. You can then ask the question in your
code What value does the variable componentName contain? Variables can then be
declared as a type to let us know what we can do with that information. The value of a
variable will not necessarily be constant throughout the duration a program is running.
How you decide to name your variables is very important. In the previous example,
instead of giving the input box a variable name of componentName we could have called
it ImASuperAwesomeProgrammer. However, this doesnt make a lot of sense and doesnt
help us, especially if were looking at the code months from now or another programmer
has to modify the code.

There are a few rules we must follow. Variable names, also known as identifiers, must be
less than 255 characters, they cannot start with a number, and special characters such as
spaces and periods are forbidden. Avoid naming conflicts. Two variables cannot have the
same name.
Good Variable Names: dimensionOne, dimension1
Bad Variable Names: dimension One, 1dimension

Variables have different types. To store your name in a variable, you would use a String
variable. To store your age then that type of variable would be an Integer. How much
money you make in a year would be declared as a Double. Declaring variables as a specific
type tells CATIA the information being stored will be a certain way. Storing a number as
an Integer means it will be a whole number without a decimal place, like 5, 60, or -4000. If
you try to store $58.76 as an integer you will get an error. Two variables that are both
Integers can be added or subtracted to each other (50-5=45) but it wouldnt make sense to
try to add two strings together (Emmett-David=???). Declaring variables as a type give us a
sense of what can and cant be done with them.
Variable
Type
String
Integer
Double
Long
Boolean
CATVariant
CATBStr

Default
Value
Null
0
0
0
FALSE
Null
Null

Description
Text (letters, numbers, spaces, punctuation)
Whole number
Any number, positive or negative
A 4-byte integer
Logical statement like true or false, yes or no, etc.
Index of a list of objects
String of CATIA expressions

There is a naming convention called Hungarian notation where a letter is placed in front
of the variable name to notate what type of data the variable is. For example:

o=object (i.e. oPartDoc)

s=selection (i.e sSelection1)
str=string (i.e. strFilename)
i=integer (i.e iCount)
rng=Range (i.e. rngField)

Many programmers use int or n for integer and o or obj for object. Either or works
as long as your notation is consistent and easy for others to understand.

Dimming and Setting

Variables are "dimmed" (declared) as a type, either a "primitive" type (single, double,
integer, string, etc.) or an object type (more complex). If you dont specify the type of
variable VBA declares the variable as a Variant type which can accept any type of variable.
In rare instances youll have a good reason for using a Variant. But most of the time, you
should use explicit variable types. One reason for doing so is that your code will run faster
but the primary reason is that youll reduce your coding errors due to the fact that CATIA
enforces the type of variable you specify.
The second reason that its always a good idea to declare your variable types explicitly is
that it helps to document your intentions when you write code. This documentation is
critical if you look at your code after several months have passed. Knowing whether a
variable was intended to contain a number or text can make it much easier for you to read
your old code, find errors, and then continue coding.
The "Dim" command is used to allocate a variable of any type. Primitive variables are
populated with a value. Declaring variables with a Dim statement helps save memory
while running the program. If you have two variables declared as integers you could
subtract or add them. But if you have two variables stored as names it wouldnt make sense
to subtract them because that just doesnt mean anything! Declaring the type of variable
allows you to make sense of what a variable can and cannot do.
Multiple variables of the same type can be declared all at once by using commas (Dim iNum1,
iNum2, As Integer). However, in VB6 you need a separate line of code for every Dim
statement (meaning you cant use Dim w, h As String it must be written as Dim w As
String: Dim h As String).

After a variable is declared through dimming then it is Set or given a value. Do NOT use
Set to assign a variable to an object property (MyCamera3D.ViewPoint3D) or an intrinsic
type variable (mystring = directory) For object variables, the "Set" command is used to
"point" the variable to the object. Within the program, the variable then represents that
object unless it is "Set" to a different one.

Tutorial 1.3: Create Your First Custom Hello World Macro

Its time to follow along to create your first CATIA macro. In the programming world, the
term Hello World typically refers to the most basic program that can be written in a given
language. Think of it like this, if you can write a Hello World CATIA macro, this means you
are able to setup the necessary tools, write the code, compile the macro, and run the
program. Not a bad start!
1. To begin, create a new macro library using VBA Projects instead of Directories.

2. Create a new macro using the MS VBA language (most examples in this book are
either VBA or CATScript).

3. Rename the macro to Exercise1 then double click or hit edit to begin editing the
macro in the VBA editor.

4. Go to Tools > References and make sure all available CATIA references are selected.

5. By default, CATIA doesnt force you to declare your variables. However, you should
change that setting immediately. In CATIA (or Excel or other software), press
Alt+F11 to launch the Visual Basic Editor (VBE). Go to Tools>Options.

6. In the Editor tab of the Options dialog, make sure that theres a check mark in front
of Require Variable Declaration

.
7. After you click OK, insert a new Module. When you do so, youll see Option Explicit
as the first line of the module. This line tells CATIA that all variables must be
declared making your code easier to read and follow. Option Explicit will be the first
line in our code.
8. A CATIA VB program or "macro" consists of a "Subroutine" named CATMain().
CATIA only recognizes Sub CATMain as the entry point to any VBA application.
Every Sub must end with an End Sub. Between the two Sub statements, type the text as
shown:
Option Explicit
Sub CATMain()
'declare a variable as a String type
Dim strMessage As String
'define the String variable as the text Hello World
strMessage = "Hello world!"
'have a message box display the text in CATIA
Msgbox strMessage
End Sub

9. Save then run the macro by clicking the play icon, going to the run menu, or by
pressing F5. A message box should pop-up displaying Hello world!. Click ok to
end the program. Voila! You have just setup, coded, and ran your first CATIA
macro, your first accomplishment as a programmer.

Tutorial 1.4: Create a Macro Icon

Instead of having to open the macro window to run your program every time, it can be
much quicker to assign an icon to macro and place it on a toolbar for quick access. To
assign an icon for your recently created Hello World macro:

1. Go to Tools>Customize then the Commands tab.

2. Scroll down to Macros and click "Show Properties." Under Commands, select the Hello
World macro then click the "" box. The icon browser pops up. There are over 9,000 unique
icons to choose from (or you can create your own). Select one that makes sense to you
and is different from any others you currently use then hit Close.

3. Finally, drag and drop the macro file from the command window to whatever toolbar
you would like the icon to appear on (such as "Graphic Properties" or create a new one).

Now you can click the Icon to run your macro! You can also setup custom keyboard
shortcuts from within the same window as well or create your own custom toolbar by
going to Tools>Customize>Toolbars>New.

Chapter 1 Quiz
Test your knowledge of the material presented in Chapter 1.

1. True or False: Macros can be recorded in the Drafting workbench.

2. What is the keyboard shortcut to open the CATIA macros window?

3. What is the keyboard shortcut to open the Visual Basic Editor?
4. How does code generally flow in a CATIA CATScript macro?
a. From bottom to top, left to right

b. From top to bottom, left to right

c. From top to bottom, right to left

d. From bottom to top, right to left

5. True or false: 1MainComponent is a good variable name.

6. What does IDE stand for?
7. What variable type would I use to store this data: My birthday is June 1st.
8. What is the default value of String type?

9. What is the default value of Integer type?

10. True or False: File+SaveAs will keep the same UUID.
11. If you need to store this data: -298.056 what variable type would you use?
12. If you're going to make a variable name of myName and assign a value of Emmett
Ross, what type would you use?
13. What type of variable would you use to store this data: 76?
14. If using CATIA V5, what will the following codes message box output be?
Sub CATMain()

MsgBox CATIA.Caption
End Sub

15. For VBAs syntax, which statement is true:

a. VBA is not case sensitive
b. Comments are denoted using a \ symbol
c. Semicolon(:) is carry over to the next line
d. All of the above