International Journal of Scientific and Research Publications, Volume 6, Issue 6, June 2016

ISSN 2250-3153

486

Single Axis Solar Tracking System using Microcontroller

(ATmega328) and Servo Motor
Krishanu Das, Hridi Ghosh, Maitrayee Sengupta
Dept. of ECE, Dr Sudhir Chandra Sur Degree Engineering College, Kolkata 700074, India.

Abstract- As the energy demand and the environmental problems

increase, the natural energy sources have become very important
as an alternative to the conventional energy sources. The
renewable energy sector is fast gaining ground as a new growth
area for numerous countries with the vast potential it presents
environmentally and economically. Solar energy plays an
important role as a primary source of energy, especially for rural
area. This project aims at the development of process to track the
sun and attain maximum efficiency using Arduino Uno for real
time monitoring. The project is divided into two stages, which
are hardware and software development. In hardware
development, two light dependent resistor (LDR) has been used
for capturing maximum light source. Servo motor has been used
to move the solar panel at maximum light source location sensing
by LDR. The performance of the system has been tested and
compared with static solar panel. This project describes the
design of a low cost, solar tracking system.

can be used as PWM outputs), 6 analog inputs, a

16 MHz ceramic resonator, a USB connection, a power jack, an
ICSP header, and a reset button. It contains everything needed to
support the microcontroller; simply connect it to a computer with
a USB cable or power it with a AC-to-DC adapter or battery to
get started.
2.2 SPECIFICATIONS:
Microcontroller : ATmega328
Operating Voltage
: 5V,Input Voltage (recommended) :
7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 14 (of which 6 provide PWM output),
Analog Input Pins :6,DC Current per I/O Pin:40 mA, DC Current
for 3.3V Pin :50 mA
Flash Memory :32 KB of which 0.5 KB used by bootloader,
SRAM:2 KB
EEPROM :1 KBClock Speed:16 MHz

Index Terms- Solar tracker, Arduino ATmega 328, LDR, Single

Axis ,Energy storage system

I. INTRODUCTION

racker systems follow the sun throughout the day to

maximize energy output. The Solar Tracker is a proven
single-axis tracking technology that has been custom designed to
integrate with solar modules and reduce system costs. The Solar
Tracker generates up to 25% more energy than fixed mounting
systems and provides a bankable energy production profile
preferred by utilities.
2.1 BlOCK DIAGRAM:

Arduino UNO Basic Information:

The Arduino Uno is a microcontroller board based on
the ATmega328.It has 14 digital input/output pins (of which 6

2.3 SERVO MOTOR:

Servo motors have been around for a long time and are used
in many applications. They are small in size but pack a big punch
and are very energy efficient. Because of these features, they can
be used to operate remote-controlled or radio-controlled toy
cars, robots and airplanes. Servo motors are also used in
industrial applications, robotics, in-line manufacturing,
pharmaceutics and food services.
Servos are controlled by sending an electrical pulse of
variable width, or pulse width modulation (PWM), through the
control wire. There is a minimum pulse, a maximum pulse and a
repetition rate. A servo motor can usually only turn 90 in either
direction for a total of 180 movement. The motor's neutral
position is defined as the position where the servo has the same
amount of potential rotation in the both the clockwise or counterclockwise direction. The PWM sent to the motor determines

www.ijsrp.org

International Journal of Scientific and Research Publications, Volume 6, Issue 6, June 2016
ISSN 2250-3153

position of the shaft, and based on the duration of the pulse sent
via the control wire the rotor will turn to the desired position.
The servo motor expects to see a pulse every 20 milliseconds
(ms) and the length of the pulse will determine how far the motor
turns. For example, a 1.5ms pulse will make the motor turn to the
90 position. Shorter than 1.5ms moves it to 0 and any longer
than 1.5ms will turn the servo to 180. When these servos are
commanded to move, they will move to the position and hold
that position. If an external force pushes against the servo while
the servo is holding a position, the servo will resist from moving
out of that position. The maximum amount of force the servo can
exert is called the torque rating of the servo. Servos will not hold
their position forever though; the position pulse must be repeated
to instruct the servo to stay in position.
2.4 LDR-LIGHT DEPENDENT RESISTOR:
A Light Dependent Resistor (LDR) is also called a photo
resistor or a cadmium sulfide (CdS) cell. It is also called a
photoconductor. It is basically a photocell that works on the
principle of photoconductivity. The passive component is
basically a resistor whose resistance value decreases when the
intensity of light decreases. This optoelectronic device is mostly
used in light varying sensor circuit, and light and dark activated
switching circuits. Some of its applications include camera light
meters, street lights.
LDR Structure and Working:The basic structure of an
LDR is shown below.

The snake like track shown below is the Cadmium Sulphide

(CdS) film which also passes through the sides. On the top and
bottom are metal films which are connected to the terminal leads.
It is designed in such a way as to provide maximum possible
contact area with the two metal films. The structure is housed in
a clear plastic or resin case, to provide free access to external
light. As explained above, the main component for the
construction of LDR is cadmium sulphide (CdS), which is used
as the photoconductor and contains no or very few electrons
when not illuminated. In the absence of light it is designed to
have a high resistance inthe range of megaohms. As soon as light
falls on the sensor, the electrons are liberated and the
conductivity of the material increases. When the light intensity
exceeds a certain frequency, the photons absorbed by the
semiconductor give band electrons the energy required to jump
into the conduction band. This causes the free electrons or holes
to conduct electricity and thus dropping the resistance
dramatically (< 1 Kiloohm).
2.5 GEAR:
A toothed wheel that works with others to alter the relation
between the speed of a driving mechanism (such as the engine of
a vehicle) and the speed of the driven parts (the wheels).

487

What do gears do... and how do they do it?Gears are used

for transmitting power from one part of a machine to another. In
a bicycle, for example, it's gears (with the help of a chain) that
take power from the pedals to the back wheel. Similarly, in a car,
gears transmit power from the crankshaft (the rotating axle that
takes power from the engine) to the driveshaft running under the
car that ultimately powers the wheels.
Increase speed: If we connect two gears together and the
first one has more teeth than the second one (generally that
means it's a bigger-sized wheel), the second one has to turn
round much faster to keep up. So this arrangement means the
second wheel turns faster than the first one but with less force.
Increase force: If the second wheel in a pair of gears has
more teeth than the first one (that is, if it's a larger wheel), it
turns slower than the first one but with more force.
Change direction: When two gears mesh together, the
second one always turns in the opposite direction. So if the first
one turns clockwise, the second one must turn counterclockwise.
We can also use specially shaped gears to make the power of a
machine turn through an angle. In a car, for example, the
differential (a gearbox in the middle of the rear axle of a rearwheel drive car) uses a cone-shaped bevel gear to turn the
driveshaft's power through 90 degrees and turn the back wheels.
Four different ways to use gears:
Gears for speed:In this simple gearbox, we got (from right
to left) a large gear wheel with 40 teeth, a medium wheel with 20
teeth, and a small wheel with 10 teeth. When we turn the large
wheel round once, the medium wheel has to turn twice to keep
up. Similarly, when the medium wheel turns once, the small
wheel has to turn twice to keep up. So, when we turn the large
gear wheel on the right, the small wheel on the left turns four
times faster but with one quarter as much turning force. This
gearbox is designed for increasing speed.
Gears for force: If we power the same gearbox in the
opposite direction, by turning the small wheel, I'll make the large
wheel spin a quarter as fast but with four times as much force.
That's useful if I need to make a heavy truck go up a hill, for
example.
Worm gears: Here we use an electric motor (the gray box
on the right) and a long screw-like gear to drive a large gear
wheel. This arrangement is called a worm gear. It reduces the
speed of the motor to make the large wheel turn with more force,
but it's also useful for changing the direction of rotation in geardriven machinery.
Rack and pinion gears: We've probably seen one of these
in cliff- and hill-climbing rack railroads, but they're also used in
car steering systems, weighing, and many other kinds of
machines as well. In a rack and pinion gear, a slowly spinning
gear wheel (the pinion) meshes with a flat ridged bar (the rack).
If the rack is fixed in place, the gear wheel is forced to move
along it (as in a railroad). If the gear is fixed, the pinion shifts
instead. That's what happens in car steering: we turn the steering
wheel (connected to a pinion) and it makes a rack shift from side
to side to swivel the car's front wheels to the left or the right. In
simple weighing scales, when you load a weight on the pan at the
top, it pushes a rack straight downward, causing a pinion to
rotate. The pinion is attached to a pointer that rotates as well,
showing the weight on the dial.
www.ijsrp.org

International Journal of Scientific and Research Publications, Volume 6, Issue 6, June 2016
ISSN 2250-3153

II. SCHEMATIC OF THE ARDUINO SOLAR TRACKER CIRCUIT

Methodology:
The main impulsion is to design a high quality solar tracker.
This paper is divided into two parts; hardware and software. It
consists of three main constituent which are the inputs, controller
and the output as shown in Fig B photo resistor or Lightdependent resistor (LDR) or photocell is a light-controlled
variable resistor. LDRs or Light Dependent Resistors are very
useful especially in light/dark sensor circuits. Normally the
resistance of an LDR is very high, sometimes as high as 1000
000 ohms, but when they are illuminated with light resistance
drops dramatically. LDRs have low cost and simple structure.
The Servo motor can turn either clockwise or anticlockwise
direction depending upon the sequence of the logic signals. The
sequence of the logic signals depends on the difference of light
intensity of the LDR sensors. The principle of the solar tracking
system is done by Light Dependant Resistor (LDR). Two LDRs
are connected to Arduino analog pin AO to A1 that acts as the
input for the system. The built-in Analog-to-Digital Converter
will convert the analog value of LDR and convert it into digital.
The inputs are from analog value of LDR, Arduino as the
controller and the Servo motor will be the output. LDR1 and
LDR2 are taken as pair .If one of the LDR gets more light
intensity than the other, a difference will occur on node voltages
sent to the respective Arduino channel to take necessary action.
The Servo motor will move the solar panel to the position of the
high intensity LDR that was in the programming.

III. ALGORITHM AND C CODE

Step 1.Read all analog voltages from analog channels
Step 2.If all voltages are equal then Servo motor will be in
stop position.
Step 3.If LDR1>LDR2 Then the Servo motor will rotate
clockwise.
Step 4.If LDR2>LDR1 Then the down motor will rotate anti
clockwise.
Code:
#include <Servo.h>
Servo myservo;
int pos=0; // Variable to store the servo position .
int inputPhotoLeft=1; //Easier to read, instead of just 1 or 0.
int inputPhotoRight=0;
int Left=0;// Store reading from the photo resistors.

488

int Right=0;// Store reading from the photoresistors.

void set up ()
{
myservo.attach(9); //Attach servo to pin 9.
}
void loop()
{
//Read the values from the photoresistors to the Left and Right
variables.
Left=analogRead(inputPhotoLeft);
Right=analogRead(inputPhotoRight);
// Checks if Right is greater than Left, if so move to right.
if (Left > (Right+20))
// +20 is the deadzone, so it would not jiggle back and forth.
{
if (pos < 55)
pos++;
myservo.write(pos);
}
// check if left is greater than right, if so move to left.
if (Right > (Left+20))
// +20 is the deadzone, so it wouldnot jiggle back and forth.
{
if (pos > 55)
pos--;
myservo.write(pos);
}

IV. CONCLUSION
Solar trackers generate more electricity than their stationary
counterparts due to an increased direct exposure to solar
rays.There are many different kinds of solar tracker, such as
single-axis and dual-axis trackers, which can help us find the
perfect fit for our unique jobsite. Installation size, local weather,
degree of latitude, and electrical requirements are all important
considerations that can influence the type of solar tracker thats
best for us.Solar trackers generate more electricity in roughly the
same amount of space needed for fixed tilt systems, making them
ideal optimizing land usage.Solar trackers are slightly more
expensive than their stationary counterparts, due to the more
complex technology and moving parts necessary for their
operation.
Some ongoing maintenance is generally required, though
the quality of the solar tracker can play a role in how much and
how often this maintenance is needed.

REFERENCES
[1]

[2]

[3]

J. A. Beltran, J. L. S. Gonzalez Rubio, C.D. Garcia-Beltran: Design,

Manufacturing and Performance Test of a Solar Tracker Made by an
Embedded Control, CERMA 2007, Mexico
O. Stalter, B. Burger, S. Bacha, D. Roye: Integrated Solar Tracker
Positioning Unit in Distributed Grid-Feeding Inverters for CPV Power
Plants, ICIT 2009, Australia
M. A. Panait, T. Tudorache: A Simple Neural Network Solar Tracker for
Optimizing Conversion Efficiency in Off-Grid Solar Generators, ICREPQ
2008, Spain

www.ijsrp.org

International Journal of Scientific and Research Publications, Volume 6, Issue 6, June 2016
ISSN 2250-3153
[4]

[5]
[6]

[7]

[8]

[9]

A. M. Morega, J. C. Ordonez, P. A. Negoias, R. Hovsapian: Spherical

Photovoltaic Cells A Constructal Approach to Their Optimization,
OPTIM 2006, Romania
A. M. Morega, A. Bejan: A Constructal Approach to the Optimal Design of
Photovoltaic Cells, Int. Journal of Green Energy, pp. 233-242, 2005
J. Horzel, K. De Clerq: Advantages of a New Metallization Structure for the
Front Side of Solar Cells, 13th EC Photovoltaic Solar Energy Conference,
France, 1995
P. I. Widenborg, G. Aberle: Polycrystalline Silicon Thin-Film Solar Cells
on AIT-Textured Glass Superstrates, Advances in OptoElectronics Journal,
Vol. 2007
P. A. Basore: Manufacturing a New Polycrystalline Silicon PV Technology,
Conference Record of the 2006 IEEE 4th World Conference on
Photovoltaic Energy Conversion, pp. 2089-2093, 2006
P. Turmezei: Chalcogenide Materials for Solar Energy Conversion, Acta
Polytechnica Hungarica, Vol. 1, No. 2, pp. 13-16, 2004

489

[10] Technosoft: IBL2403 Intelligent Drive User Manual

AUTHORS
First Author Krishanu Das, Dept. of ECE, Dr Sudhir Chandra
Sur Degree Engineering College, Kolkata 700074, India.
Second Author Hridi Ghosh, Dept. of ECE, Dr Sudhir
Chandra Sur Degree Engineering College, Kolkata 700074,
India.
Third Author Maitrayee Sengupta, Dept. of ECE, Dr Sudhir
Chandra Sur Degree Engineering College, Kolkata 700074,
India.

www.ijsrp.org