Scribd
Upload
561 views

GA 713 BV/NV Configuration Option Progamming Card: Insert This End First

This document provides instructions for programming configuration options on a GA 713 BV/NV device using a programming card. It includes the following steps: 1. Select the correct width card for the bezel and cut out the card outline. 2. Fill in the appropriate sections of the card to select configuration options like interface type, pulse settings, options and inhibits. 3. Insert the programmed card into the BV/NV device to upload the new configuration settings. The device will flash LEDs to indicate if programming was successful or if errors occurred.

Uploaded by

asritaip
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
561 views

GA 713 BV/NV Configuration Option Progamming Card: Insert This End First

This document provides instructions for programming configuration options on a GA 713 BV/NV device using a programming card. It includes the following steps: 1. Select the correct width card for the bezel and cut out the card outline. 2. Fill in the appropriate sections of the card to select configuration options like interface type, pulse settings, options and inhibits. 3. Insert the programmed card into the BV/NV device to upload the new configuration settings. The device will flash LEDs to indicate if programming was successful or if errors occurred.

Uploaded by

asritaip
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

GA 713 BV/NV Configuration Option Progamming Card

Instructions for use

Insert this end first

1 - Select correct width card for bezel. Cut card around


outline - check measurements as printed. Check print
options Page scaling is set to None when printing a pdf
file to ensure correct size.

IF 30

IF 31

CCTALK

SIO

PARALLEL

SP 4

NIS

IF 32

I/F Spare 1

I/F Spare 2

I/F Spare 3

High 50ms

High 100ms

Low 50ms

Low 100ms

Bill 1

Bill 5

Bill 2

Bill 6

Bill 3

Bill 7

Bill 4

Bill 8

High Speed

cctalk plain

Start Disabled

cctalk 8 bit chk

Low Power

Binary

Credit Hold

No escrow t/out

GOOD

66mm

OK

BAD

3 - Power-up BV and allow to reset.


4 - Click Function button on BV/NV to access Configuration
Mode, Uint bezel LEDs should be flashing at 1 second
interval.
5 - Enter card into BV/NV in direction indicated by arrows.

204mm

MDB

Speed

PULSE

Pulses Per
Dollar

SSP

6 - Card will be rejected and if configuration was good the,


bezel LEDs will flash at a fast rate while programming takes
place. TAKE CARE TO ENSURE THE POWER IS NOT
REMOVED AT THIS STAGE, THE BV MAY SUFFER
PERMANENT DAMAGE !! The BV will then reset.
7 - If an error has occurred, the card will be rejected and the
bezel LEDs will flash slowly a number of times to indicate
the error cause. (See table below for codes).
8 - IMPORTANT - CHECK THAT THE CONFIGURATION
Flash
Error
______________________________________________
2

V1.9

Options

Inhibits

Pulse Settings

Interface

2 - Fill in sections as required. Take care to fill in the


sections correctly, keep inside the lines and fill boxes fully
as example below:

Invalid card read - card entered wrong way round,


card mis-read or card wrong version.
______________________________________________
3
No interface selection was detected on card.
______________________________________________
4
Multiple interface selection detected.
______________________________________________
5
Invalid interface selected - the selected interface is
not available for this unit.
______________________________________________
6
Selected interface not compatible with uint
version.
______________________________________________
7
Pulse configuration error. Selected pulse options
invalid.(e.g. multiple pulse per dollar)
______________________________________________
8
ccTalk configuration error. Selected cctalk options
invalid. (cctalk 8 bit chk not allowed without ccTalk
Plain.)
______________________________________________
9

Low power mode not available on this uint version.

GA713-1-9

Program Check Procedure

To check settings on a programmed unit:


1 - Power on unit.
2 - Click program set button on unit twice (like double click on mouse).
3 - Monitor bezel led and check flash codes on table below

SSP
Pulse
MDB
IF 30
IF 31
cctalk
SIO
Parallel
SP4
NIS
IF 32
spare
spare
spare

Flash count Pulse High Pulse Low Pulse per dollar High speed Disabled cctalk plain cctalk 8 bitlowpower binary Credit Hold No escrowt/out
1
2
ms/10
ms/10
value
3 flash
3
4
5
6
1 flash 2 flashes
3 flashes
7
1 flash 2 flashes
3 flashes
8
1 flash
2 flashes
9
ms/10
ms/10
value
3 flash
10
11
1 flash
12
13
14

For example:
A pulse inteface with 50ms high, 100ms low, 2 pulse per dollar will flash as follows 2,5,10,2
A SSP interface will only ever flash once
A cctalk interface with 16 bit checksum, no encryption wil flash 6,1
A cctalk interface with 8 bit checksum, no encryption wil flash 6,1,2
A Binary interface will flash 8,1

66mm Bezel

PULSE

MDB

IF 30

MDB

IF 30

IF 31

CCTALK

IF 31

CCTALK

SIO

PARALLEL

SIO

PARALLEL

SP 4

NIS

SP 4

NIS

IF 32

I/F Spare 1

IF 32

I/F Spare 1

I/F Spare 2

I/F Spare 3

I/F Spare 2

I/F Spare 3

High 50ms

High 100ms

High 50ms

High 100ms

Low 50ms

Low 100ms

Low 50ms

Low 100ms

Bill 1

Bill 5

Bill 1

Bill 5

Bill 2

Bill 6

Bill 2

Bill 6

Bill 3

Bill 7

Bill 3

Bill 7

Bill 4

Bill 8

Bill 4

Bill 8

High Speed

cctalk plain

High Speed

cctalk plain

Start Disabled

cctalk 8 bit chk

Start Disabled

cctalk 8 bit chk

Low Power

Binary

Low Power

Binary

Credit Hold

No escrow t/out

Credit Hold

No escrow t/out

66mm

V1.9 66

66mm

Pulse Settings
Options

Inhibits

204mm

Speed
Pulses Per
Dollar

204mm

SSP

Pulses Per
Dollar

PULSE

Interface

SSP

Speed

Insert this end first

V1.9 66

Options

Inhibits

Pulse Settings

Interface

Insert this end first

72mm Bezel

MDB

IF 30

MDB

IF 30

IF 31

CCTALK

IF 31

CCTALK

SIO

PARALLEL

SIO

PARALLEL

SP 4

NIS

SP 4

NIS

IF 32

I/F Spare 1

IF 32

I/F Spare 1

I/F Spare 2

I/F Spare 3

I/F Spare 2

I/F Spare 3

High 50ms

High 100ms

High 50ms

High 100ms

Low 50ms

Low 100ms

Low 50ms

Low 100ms

Bill 1

Bill 5

Bill 1

Bill 5

Bill 2

Bill 6

Bill 2

Bill 6

Bill 3

Bill 7

Bill 3

Bill 7

Bill 4

Bill 8

Bill 4

Bill 8

High Speed

cctalk plain

High Speed

cctalk plain

Start Disabled

cctalk 8 bit chk

Start Disabled

cctalk 8 bit chk

Low Power

Binary

Low Power

Binary

Credit Hold

No escrow t/out

Credit Hold

No escrow t/out

72mm

72mm

Pulse Settings
Options

Inhibits

204mm

Speed
Pulses Per
Dollar

204mm

PULSE

Pulses Per
Dollar

SSP

V1.9 72

PULSE

Interface

SSP

Speed

Insert this end first

V1.9 72

Options

Inhibits

Pulse Settings

Interface

Insert this end first

82mm Bezel

MDB

IF 30

MDB

IF 30

IF 31

CCTALK

IF 31

CCTALK

SIO

PARALLEL

SIO

PARALLEL

SP 4

NIS

SP 4

NIS

IF 32

I/F Spare 1

IF 32

I/F Spare 1

I/F Spare 2

I/F Spare 3

I/F Spare 2

I/F Spare 3

High 50ms

High 100ms

High 50ms

High 100ms

Low 50ms

Low 100ms

Low 50ms

Low 100ms

Bill 1

Bill 5

Bill 1

Bill 5

Bill 2

Bill 6

Bill 2

Bill 6

Bill 3

Bill 7

Bill 3

Bill 7

Bill 4

Bill 8

Bill 4

Bill 8

High Speed

cctalk plain

High Speed

cctalk plain

Start Disabled

cctalk 8 bit chk

Start Disabled

cctalk 8 bit chk

Low Power

Binary

Low Power

Binary

Credit Hold

No escrow t/out

Credit Hold

No escrow t/out

82mm

82mm

Pulse Settings
Options

Inhibits

204mm

Speed
Pulses Per
Dollar

204mm

PULSE

Pulses Per
Dollar

SSP

V1.9 82

PULSE

Interface

SSP

Speed

Insert this end first

V1.9 82

Options

Inhibits

Pulse Settings

Interface

Insert this end first

You might also like