Scribd
Upload
4K views

8051 Willar Programmer

This document describes an 8051 microcontroller and EEPROM programmer that is powered via USB and supports various 8-bit microcontrollers and serial EEPROMs. It has a 40-pin ZIF socket for easy insertion and removal of chips and fast programming via its USB interface. The programmer supports various 8051 microcontroller families as well as common serial EEPROMs and has an easy to use software interface for selecting devices, loading hex files, and programming, verifying and locking chips with options like reading from one chip to program another.

Uploaded by

Heriberto Flores Ampie
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
4K views

8051 Willar Programmer

This document describes an 8051 microcontroller and EEPROM programmer that is powered via USB and supports various 8-bit microcontrollers and serial EEPROMs. It has a 40-pin ZIF socket for easy insertion and removal of chips and fast programming via its USB interface. The programmer supports various 8051 microcontroller families as well as common serial EEPROMs and has an easy to use software interface for selecting devices, loading hex files, and programming, verifying and locking chips with options like reading from one chip to program another.

Uploaded by

Heriberto Flores Ampie
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

8051 & EEPROM PROGRAMMER

Details
This is programmer for 89 series microcontroller devices in 20 & 40 pin packages and supports various 8 pin serial
EEPROM ICs. ZIF socket enables easy insertion and removal of devices for programming. Programming is very fast since
it is USB based. No external power required since it is powered from USB port itself.
Features

Supports 89 series & serial EEPROM devices


Powered from USB port(No external power required)
High speed writing (8kb flash file in 10 seconds)
Auto Identify connected programmer
Error checking and verification in-built
Lock of programs in chip supported to prevent program copying
40 pin ZIF socket for easy insertion & removal
Auto Erase/Lock/Verify
Informative window and access to latest programmed file
Simple and Easy to use

Supported Devices
Atmel
AT89C51,AT89C52,AT89S51,AT89S52,AT89S53,AT89S8252,AT89C1051,AT89C2051,AT89C4051,
Winbond
W78E51,W78E52
SST
SST89C54,SST89C58,SST89C59,SST89E54RD,SST89E58RD,SST89E554RC
Serial EEPROM
AT24C01,AT24C02,AT24C04,AT24C08,AT24C16,AT24C32,AT24C64,AT24C164,AT93C46,AT93C56,AT93C66

Specification
Communication USB 2.0 compliant
Power +5V from USB Cable
Cable USB A to B type

Getting started for first time use

8051 & EEPROM PROGRAMMER

Step #1: Install USB Driver

Install USB driver provided on CDROM in folder CP2102 DRIVER by using its setup file and
install manual as per your operating system..

Step #2: Connect Programmer to USB port & Start Software

Connect programmer to USB port. When connecting the hardware to USB the LED will blink
once and become off. It is normal indication of everything is ok and it is ready to use. Run Willar
software from desktop or start menu. Software should connect and show ONLINE icon green color
at bottom. Your programmer is ready to use. Refer to pages below to follow process.
Troubleshooting Notes

If you get Failed to connect error in software, It is possible that virtual com port is not between
COM1-COM9. Change the COM port on your system from Device Manager. Also you can try
reinstalling USB driver.
Copy the Willar Software to Hard Disk and Execute the software Window will as seen below

8051 & EEPROM PROGRAMMER


Select The SP200S SIMPLE

Select the device

8051 & EEPROM PROGRAMMER


Programming Method
Step #1: Select Device

Select Device by clicking Device button to bring device selection dialog. After selecting inserted
device click OK. To select recently used devices you can click on down arrow & select.
Step #2: Load file

PC software takes HEX or BIN file for for programming. Load > Select HEX file & click OK. To select
recently used files you can click on down arrow & select
You will see following dialog when you load a HEX extension file. You can keep all setting as default
and click OK to select this file.

Step #3: Auto Program

Click on Auto button to start programming process.

Locking Device to prevent copying


To set lock option for selected device click on Config, Mode0 is no lock and other modes are other
lock options. You can see device datasheet as to which config lock bit will be suitable in your
application. Once you set a config for particular device it is stored nand it is not required to set again.
Next time you program a particular device same config will be used to load in to device during Auto
process.

Copying from one device to another


You may wish to copy content from one programmed IC to another. For this process, first select
device and Insert Master IC from which you want to copy program then click on READ button. It will
read device memory to buffer. If you wish to see what content was read you can click on EDIT button.

8051 & EEPROM PROGRAMMER


To save this memory as HEX file you can click on SAVE button.If your master IC is locked, it will
show memory as 0xFF means its content cannot be read.Once you have saved file from master you
can use this file to load into new microcontrollers.

Other software options


Normally you will use Auto method in repeated programming task. Auto methodwill automatically do
Erase, Blank Check, Program, Verify & Protect.We have given other options like Blank, Read,
Program, Verify, Protect & Erasethat can be used individually if you wish.
Following are methods you can use
Auto: Automatically do all process below as required to load file into device
Blank: Check if device is blank
Read: Read content of inserted device into buffer
Program: Load the content of file into device
Verify: Check if loaded file content matches with device content
Protect: Program Config options to device
Erase: Erase the device.

Related Links
http://www.keil.com Keil: Commercial C & assembly compiler for 8051 devices
http://sdcc.sourceforge.net/ SDCC: Freeware C compiler for 8051 devices
http://en.wikipedia.org/wiki/Intel_HEX Intel Hex file format information

Place the chips Pin 1 Facing Towards ZIF Leaver , Then Click on Auto To Program

You might also like