Scribd
Upload
132 views

Process Capability Report Form06

The document provides instructions for suppliers on submitting process capability reports to an EMD supplier product approval process. It requires suppliers to maintain records of key product characteristic measurements and submit the data and capability analysis including calculation of Cpk. Suppliers must submit this data after their first 30 production pieces and every 30 pieces thereafter until the process is in control with a Cpk of 1.50 or higher. The document includes an optional worksheet for reporting the required information.

Uploaded by

arunrad
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
132 views

Process Capability Report Form06

The document provides instructions for suppliers on submitting process capability reports to an EMD supplier product approval process. It requires suppliers to maintain records of key product characteristic measurements and submit the data and capability analysis including calculation of Cpk. Suppliers must submit this data after their first 30 production pieces and every 30 pieces thereafter until the process is in control with a Cpk of 1.50 or higher. The document includes an optional worksheet for reporting the required information.

Uploaded by

arunrad
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 8

Process Capability Report Form

Process Capability Requirement from EMD Supplier Product Approval Process (EMD SPAP).
Process Capability Analysis
Supplier shall maintain records of all Key Product Characteristic (KPCs) measurements and submit
the data and Capability Analysis, including calculation of Cpk as follows. 1 st SPC Submission will
accompany SPAP submission if Supplier has sufficient data. . If less than 30 pieces, supplier will submit
the actual measurements for the parts shipped (most likely 2), 1st Submission of SPC analysis shown
below will be submitted when 30 pieces have been manufactured.. Supplier may use EMDs Excel
Workbook (this form), equivalent in-house forms or other software.
1st SPC
Submission

First 30 pieces (after removing assignable causes)

2 SPC Submission
nd

Next 30 pieces (include assignable causes, even if parts are scrapped)


Thereafter

Continue every 30 pieces until process is in control with Cpk 1.50 or higher then
maintain records for EMD review as needed. Supplier may now use an appropriate
sampling plan for recording data and to maintain process control. Notify SQE
whenever process goes out of control.

SQE may waive or modify this requirement for non-normal distributions and/or processes that are proven
not capable, but controlled by 100% inspection. EMD may designate other specific data be maintained
and submitted in addition to the KPC data. SPC submissions are to be made to the SQE via e-mail.
This is an optional form for reporting to the above requirement. Suppliers may use their own forms and/or
commercially available SPC software to generate the equivalent information.
See the Worksheet Tabs at the bottom of this sheet.
Information Page

This is the current Tab now being displayed.

Data Entry Page

This is where you enter all information and data. Be sure you identify your
company and the feature being analyzed. Enter the upper and lower specification
limits. Enter all data in the data table starting in the first column and completing
each column before going to the next. Never enter zeros or they will be counted as
data. Use the Clear Contents command or the delete key to clear selected cells of
unwanted data.

Control Charts

Displays X and Moving Range charts based on Data Entry Page.

Capability Chart

Displays Capability Chart and Statistics based on Data Entry Page.

EMD SQ 1005 - PCA Originated 9/15/05

Rev: New 9/15/05 -- J. Willhite

###

Data Name: ABC Corp - 4 Hour Locktite Cure


Measure (Unit) = Breakaway Torque (Ft-Lbs)
Upper Specification:.
Part Number:.

140.000
5879356

Lower Specification:.
KPC Number:.

128.000
2

Instructions:
Insert Data Name, Unit of Measure, Upper and Lower Specification limits.
Enter Data in Table below -- View Process Capability and Control Charts
on the Capability Chart and Control Charts Tabs.
Warning:
Do not make any changes to the other data on this page except to enter
data to the data table below for calculation of Mean and Standard
Deviation. Enter data only in the yellow cells.
Note: All Calculations assume a "normal" distribution.

Mean and Standard Deviation Calculator:

Mean =
Standard Deviation =

Data Table - enter up to 300 measurements of a single variable.


Cpk =
Enter in manufactured sequence, completing each column before going to the next.
135
135
135
135
131.75
131.75
131.75
131.75
134
134
134
134
134
134
134
134
134
134
134
134
135
135
135
135
132
132
132
132
134
134
134
134
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133.2
133.2
133.2
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133
133.5
133.5
133.5
133.5
133.5
133.5
132.5
132.5
132.5
133
133
133
132.5
132.5
132.5

133.320
0.879
2.018

136

136

136

ABC Corp - 4 Hour Locktite Cure


Breakaway Torque (Ft-Lbs)

137

Part
5879356
Number:.
KPC
Number:.2

Run Chart - Individual X

136
135
134

X Data
Column M
LCL
Column O
UCL
Column N
X Bar

133
132
131
130
129
128

Moving Range Chart


4
3.5
3
2.5
2
1.5
1
0.5
0

Moving R
Column P
UCL

nM

nO

nN

gR

mn P

Part Number:.
5879356
KPC Number:.2

ABC Corp - 4 Hour Locktite Cure

Normal Curve and Statistics Assume "Normal Distribution" .

3 Sigma
Specification
Specification
Standard
DeviationLimits
= 0.879

126.000

ABC Corp - 4 Hour Locktite Cure


Mean = 133.320
Cpk = 2.018
1

6 Sigma Capability
1

2
1

128.000

130.000

132.000

134.000

136.000

Breakaway Torque (Ft-Lbs)

138.000

140.000

142.000

You might also like