Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
To indicate clearly a specific section revised within text, 1 is shown at the left margin of the
corresponding revised section.
The number inside 1 represents the number of times the revision has been made.
To indicate clearly a specific page that contains a revision or revisions, the page number appearing at the left or right bottom of the specific page is marked with 1 .
The number inside 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
2011/09
1.05
Error correction
2011/07
1.04
Error correction
2010/09
1.03
Error correction
2010/06
1.02
Error correction
2010/05
1.01
2010/04
1.0
Error correction
Date
Service manual Ver.
Revision mark
Issue of the first edition
Descriptions of revision
4.8
4.8.1
4. PERIODICAL MAINTENANCE PROCEDURE
Fusing section
Replacing the fusing unit
CAUTION
The temperature gets high in the vicinity of the fusing unit. You may get
burned when you come into contact with the area. Before replacement
operations, make sure that more than 20 minutes have elapsed since the
main and sub power switches were turned off.
bizhub 423/363/283/223
Field Service Ver. 1.0 Apr. 2010
B. Procedure
1. Open the right door.
2. Remove the scanner right front cover.
See P.68
3. Open the paper exit upper guide [1].
[1]
A1UDF2C549DA
[1]
[2]
4. Remove the screw [1], and remove
the cover [2].
A1UDF2C551DA
55
MAINTENANCE
A. Periodically replacing parts/cycle
Fusing unit:
Every 450,000 counts (bizhub 423)
Every 450,000 counts (bizhub 363)
Every 420,000 counts (bizhub 283)
Every 340,000 counts (bizhub 223)
10. UTILITY
C. Apply Levels/Groups to Users
(1) Use
Sets Apply Level or Apply Group for individual users.
(2) Procedure
1. Select a registered user. Touch [Apply Group] and [Apply Level] independently to make
each settings.
10.6.32
bizhub 423/363/283/223
Field Service Ver. 1.0 Apr. 2010
User Authentication/Account Track-Authentication Device Settings
It will be displayed only when the extension server is used for user authentication.
It will be displayed only when the hard disk is installed.
A. General Settings
(1) Use
Specifies a device used for user authentication.
Card Authentication : Select the IC card type and operation settings.
Bio Authentication
: Select the beep and operation settings.
(2) Procedure
Card Authentication
Bio Authentication
The screen displays the authentication device that is selected in [Service Mode] [Billing Setting] [Management Function Choice] [Authentication Device 2].
When [Card 1] is selected as the authentication device, select the card type from among
[FeliCa], [TypeA], [SSFC], [FCF], and [FCF (Campus)] and make the operation settings.
If [FeliCa+Type A], [SSFC+Type A], [FCF+Type A], or [FCF (Campus)+Type A] is
selected, both the FeliCa and Type A cards can be used in this machine at the same
time.
When [Card 2] is selected as authentication device, the authentication device name will
be displayed differently depending on the type of installed loadable device driver.
If SSFC (Shared Security Formats Cooperation) is selected in Card Authentication, set
[Company Code], [Company Identification Code], [Area No.], [Building No.], [Floor No.],
[Room No.], and [Security Level].
If LEGIC (PID) is selected in Card Authentication, perform the access setting (STAMP
input) for LEGIC (PID).
If MIFARE (PID) is selected in Card Authentication, perform the MIFARE key setting.
257
ADJUSTMENT / SETTING
Select either one of the authentication devices and press the corresponding key to go to
the individual operation setting screen.
10. UTILITY
(3) How to set the card information when using SSFC card.
When using SSFC card for user authentication, get the following information from the
administrator.
And it is necessary to convert the information into the value for the control panel.
Necessary information
Sampled-data
(hexadecimal number)
Setting value
on the control panel
Item
Sampled-data
Room Number
37 (decimal number)
00 25
37 *1
Floor Number
15 (decimal number)
00 0F
15 *1
Building Number
50 (decimal number)
00 32
50 *1
Area Number
85 (decimal number)
00 55
85 *1
Security Level
2 (decimal number)
00 02
2 *1
Company
Identification Code
(CL Code) *2
06BGLQVX17
(ASCII code)
30 36 42 47 4C 51
56 58 31 37
30 36 42 47 4C 51
56 58 31 37
Company Code *3
CompanyA
(ASCII code)
CompanyA
bizhub 423/363/283/223
Field Service Ver. 1.0 Apr. 2010
B. Logoff Settings
(1) Use
Select whether or not the user is logged off after a scan or fax is sent or after the copy
document is scanned.
(2) Procedure
The default setting is Do not log off.
Do not log off
Log off
257-1
ADJUSTMENT / SETTING
*1: Enter the value as a decimal number format.
*2: The character length of the company code is 10 bytes.
*3: Use alphabetical upper case/lower case characters and numeric characters for Company code. When the company code is not set, this space will be left blank.
Item
Detection timing
Trouble isoRank
lation
CC173 Dynamic link error during
starting (AP3)
CC174 Dynamic link error during
starting (AP4)
CC180 Dynamic link error during
starting (LDR)
CC181 Dynamic link error during
starting (IBR)
CC182 Dynamic link error during
starting (IID)
CC183 Dynamic link error during
starting (IPF)
CC184 Dynamic link error during
starting (IMY)
CC185 Dynamic link error during
starting (SPF)
CC186 Dynamic link error during
starting (OAP)
CC170 Dynamic link error during
starting (AP0)
CC171 Dynamic link error during
starting (AP1)
CC172 Dynamic link error during
starting (AP2)
A dynamic link error occurs in the program
on the MFP board due to an insufficient
memory space available, a ROM fault, or
other reason when the main power switch is
turned ON.
CC190 Outline font load error
An error occurred while loading the outline
font.
CC191 Setting parameter load
error (LDR)
Upon startup, the processing of the loadable
device driver setting data file failed.
- RAM disk file creation failed.
- Reading from the flash ROM failed.
- An error occurred in API of the authentication module.
CC211 Authentication device
general error
When using the authentication device,
authentication data is not to meet the specifications.
CC212 User validation error
An error occurred while validating the user
authentication information.
CC213 User registration error/
card information setting
error
IC card advanced settings data or authentication information data is not correct when
starting-up the authentication device, setting
the IC card advanced settings or registering/
editing the authentication information.
CC214 User information deletion
error
The deletion of the user information is
uncompleted.
An error occurred during user authentication
CC216 Acquisition failure of the
number of trials/Initialize
using optional authentication unit AU-102.
error of number of authentication
613
bizhub 423/363/283/223
Code
19. TROUBLE CODE
TROUBLESHOOTING
Field Service Ver. 1.0 Apr. 2010
Code
Item
19. TROUBLE CODE
Detection timing
Trouble isoRank
lation
The error in save of job data to the memory/
hard disk and its read error are detected.
CD004 Hard disk access error
(connection failure)
Unable to communicate between the hard
disk and printer control board (PRCB).
CD00F Hard disk data transfer
error
Data transfer from the hard disk is faulty.
CD010 Hard disk unformat
Unformatted hard disk is connected.
CD011 Hard disk out of
specifications mounted
A hard disk that falls outside the specifications is connected.
CD020 Hard disk verify error
The data abnormality is detected by the
HDD verify check.
CD030 Hard disk management
information reading error
The machine fails to read administrative
information data saved in the hard disk.
TROUBLESHOOTING
CD002 JOB RAM save error
bizhub 423/363/283/223
Field Service Ver. 1.0 Apr. 2010
613-1
19.5.93
19. TROUBLE CODE
CC191: Setting parameter load error
Relevant parts
MFP board (MFPB)
WIRING DIAGRAM
Step
Action
Control signal
Location (Electrical component)
Turn OFF the main power switch, wait for
10 sec. or more, and turn ON the main
power switch.
Reinstall the loadable device driver.
Rewrite the firmware.
Change MFPB.
19.5.94
bizhub 423/363/283/223
Field Service Ver. 1.0 Apr. 2010
CC211: Authentication device general error
Relevant parts
MFP board (MFPB)
Authentication device
WIRING DIAGRAM
Step
Action
Check the USB cable for proper connection
and correct as necessary.
Turn OFF the main power switch, wait for
10 sec. or more, and turn ON the main
power switch.
19.5.95
Control signal
Location (Electrical component)
CC212: User validation error
Relevant parts
Authentication device
WIRING DIAGRAM
Step
Action
Control signal
Location (Electrical component)
Check the USB cable for proper connection
and correct as necessary.
Turn OFF the main power switch, wait for
10 sec. or more, and turn ON the main
power switch.
Re-register the user authentication information.
Change authentication device.
667
TROUBLESHOOTING
MFP board (MFPB)
19.5.96
19. TROUBLE CODE
CC213: User registration error/card information setting error
Relevant parts
MFP board (MFPB)
Authentication device
WIRING DIAGRAM
Step
Action
Control signal
Location (Electrical component)
Check the USB cable for proper connection
and correct as necessary.
Turn OFF the main power switch, wait for
10 sec. or more, and turn ON the main
power switch.
Reset the authentication settings. (card
type, IC card advanced settings, and etc.)
Re-register the user authentication information.
19.5.97
bizhub 423/363/283/223
Field Service Ver. 1.0 Apr. 2010
CC214: User information deletion error
Relevant parts
MFP board (MFPB)
Authentication device
WIRING DIAGRAM
Step
Action
Check the USB cable for proper connection
and correct as necessary.
Turn OFF the main power switch, wait for
10 sec. or more, and turn ON the main
power switch.
Location (Electrical component)
CC216: Acquisition failure of the number of trials/Initialize error of number
of authentication
Relevant parts
MFP board (MFPB)
Authentication device
WIRING DIAGRAM
Step
Action
Control signal
Location (Electrical component)
Check the USB cable for proper connection
and correct as necessary.
Turn OFF the main power switch, wait for
10 sec. or more, and turn ON the main
power switch.
Reset the number of authentication trials.
667-1
TROUBLESHOOTING
19.5.98
Control signal
19.5.99
19. TROUBLE CODE
CD002: JOB RAM save error
Relevant parts
MFP board (MFPB)
Hard disk
WIRING DIAGRAM
Step
Action
Check the connector between hard diskMFPB PJ11 for proper connection and correct as necessary.
Control signal
Location (Electrical component)
Format hard disk.
Change hard disk.
Change MFPB.
bizhub 423/363/283/223
Field Service Ver. 1.0 Apr. 2010
19.5.100 CD004: Hard disk access error (connection failure)
19.5.101 CD00F: Hard disk data transfer error
19.5.102 CD020: Hard disk verify error
Relevant parts
MFP board (MFPB)
Hard disk
WIRING DIAGRAM
Step
Action
Location (Electrical component)
Check the connector between hard diskMFPB PJ11 for proper connection and correct as necessary.
Reinstall the hard disk.
Change hard disk.
Change MFPB.
TROUBLESHOOTING
Control signal
667-2
