Series 6012-71 C-Band Technical Specifications
12.
6012-71 Installation Manual
Series 6012-71 C-Band Technical Specifications
The specifications of your antenna system are below.
12.1.
6012-71 Specifications
Above Decks Equipment
System Weight (ADE)
Weight
362-9 kg / 800 Lbs (81" Radome) M AX
Stabilized Antenna Pedestal
Assembly
Type
Three-axis (Level, Cross Level and Azimuth)
Stabilization
Torque Mode Servo / Two Axis W/Pol
Stability Accuracy
Azimuth Motor
0.1 RMS, 0.2 peak in presence of specified ship motions
(see below).
Size 23 Brushless DC Servo, Double Stacked W/Encoder
Level Motor
Size 23 Brushless DC Servo W/Brake
Cross Level Motor
Size 23 Brushless DC Servo W/Brake
Inertial Reference
3 Solid State Rate Sensors
Gravity Reference
2 MEMS Tilt Sensors
AZ transducer
256 line optical encoder / home switch
Pedestal Range of Motion:
Elevation Joint Angle
-15 to +115
Cross Level (Inclined 30)
+/- 35
Azimuth
Unlimited
Elevation Pointing
10 to 90 degrees at 25 degrees roll
5 to 90 degrees at 20 degrees roll
Relative Azimuth Pointing
0 to 90 degrees at 15 degrees roll
Unlimited
Maximum Ship Motions
Roll
+/-25 at 8-12 sec periods
Pitch
+/-15 at 6-12 sec periods
Yaw
+/-8 degrees at 15-20 sec periods
Turning rate
Up to 12 deg/sec and 15 deg/sec/sec
Headway
Up to 50 knots
Heave
0.5G
Surge
0.2G
Sway
0.2G
12-1
6012-71 Installation Manual
Series 6012-71 C-Band Technical Specifications
Specified Ship Motion (for
stability accuracy tests)
Roll
+/- 20 at 8 second period
Pitch
10 Fixed
Relative Azimuth (Heading)
0, 45 and 90 with respect to roll input
Mounting Height
Sea Tel recommends you do not exceed tangential
accelerations of 0.5G (See below chart)
Antenna Reflector C-Band
Type
Spun Aluminum axis symmetric reflector
Diameter
1.47 m / 58"
TX Gain
37.9 dBi at 6.2 GHz Typical
RX Gain
33.3 dBi at 3.7 GHz Typical
G/T (30 elevation, clear sky)
21.9 dB/k (In Radome, typical)
FCC Input Power Spectral Density
Limitation
Minimum EIRP (TVRO)
-14.0 dBW / 4 KHz
NA
C-band Feed
Type
Cross Pol Isolation
Center Focus Cassegrain feed with TX reject filter and
Cross-Pol OMT
> 120 dB
Co-Pol Isolation
NA
Port to Port Isolation
> 35 dB typical ( 30dB within 1dB contour)
Polarization
Linear w/motorized skew adjustment
Polarization Control
24 volt DC motor with pot feedback
Polarization Range of Motion
180 degrees
Receive Frequency Range
3.400-4.200 GHz
Transmit Frequency Range
5.850-6.725 GHz
12-2
Series 6012-71 C-Band Technical Specifications
6012-71 Installation Manual
Norsat 3000 Series C-Band LNB
Sea Tel Part Number: 124556-1
Gain (typical)
58 dBm
Noise temperature maximum
15K to 35K
Power requirements
+15 to +24 V supplied through center conductor of IF cable
Current (typical)
350 mA (typical)
LO Phase Noise (typical)
-73 dBc/Hz at 1 kHz
-83 dBc/Hz at 10 kHz
-93 dBc/Hz at 100 kHz
Conversion gain
55 dB min, 70 dB max
LO Stability (over temp)
5 kHz to 25 kHz
Input frequency (GHz)
3.40 to 4.20 GHz
L.O. frequency (GHz)
5.15 GHz
Output frequency (MHz)
950 to 1750 MHz
LO Radiation
-60 dBm
Image Rejection
40 dB min
1db gain copression point (typical)
+15 dBm
IP 3 (typical)
+25 dBm
Output Connector
N Connector
Impedance
50 Ohm
Input Flange
CPR-229
C-band TX Radio Package
SSPB
Codan 6700 Series, 25 or 40 Watt MBUC
Input Power
94-275 VAC, single phase
Power consumption
240 W Maximum, power factor corrected
Output Flange
WR-137
Input Connector
N Connector
RF Input Frequency Range
950-1525700 MHz
L.O. Frequency:
7.300 or 7.375 GHz user selectable (SPECTRUM
INVERTING)
5.850-6.425 GHz
RF Output Frequency Range
RF Output VSWR
RF Pout@ 1 dB GCP
Reference Frequency Level
1.5:1
44 dBm (25W) 46 dBm (40W)
Reference Frequency
-10 to +5 dBm
10 MHz
M&C Options
RS 232, RS 485
Step attenuator
0,4,8,12 dB
Alarms
Loss of lock, BUC fault
12-3
6012-71 Installation Manual
Series 6012-71 C-Band Technical Specifications
Power Supply (ADE)
A/C Input Voltage
85-264 VAC, 47-63Hz, single phase
Voltage
24 VDC, 150W
Wattage
150W (total)
Current Capacity
13.0A (total)
GPS (On Board)
Waterproof
IPX7
Operating Temperature
-30C to +60C
Storage Temperature
-40C to +60C
Humidity
Altitude
Up to 95% non-condensing or a wet bulb temperature of
+35C
-304m to 18,000m`
Vibration
IEC 68-2-64
Shock
50G Peak, 11ms
Connector
RJ11
Input Voltage
Min
4.75VDC
Typ
5.0VDC
Max
5.25VDC
NMEA output messages
GGA, GLL
Refresh Rate
1s
Integrated Control Unit (ICU)
Connectors
AC Power (J20)
85-264 VAC, 47-63Hz, single phase, 2A-1A
RF DC Power (J19)
USB (J5)
M16 (F)
Mini USB
GPS Input (J8)
RJ-11
Motor Control (J9)
DA-15S
L-Band (J16)
F-Connector
RF M&C (J7)
DE-9S
Feed (J10)
DB-25S
Service / Console (J6)
DE-9S
Serial (J14)
DE-9S
Coax Switch
LNB-A (J1)
SMA
LNB-B (J2)
SMA
Rotary Joint (J3)
Controls
SMA
Configurable from GUI
M&C Interface (J4)
Ethernet (x2)
12-4
Series 6012-71 C-Band Technical Specifications
6012-71 Installation Manual
Status LEDs
PCU Status
Diagnostic Status of the PCU
Modem Status
Configuration & Diagnostic Status of the Modem
Integrated SCPC Receiver
Tuning Range
950 to 1950 MHz in 1 KHz increments
Input RF Level
-85 to -25dBm typical
Output RF Level
Input level +/- 1dB typical
Sensitivity
30mV/dB typical (25 counts/dB typical)
Bandwidth (3dB)
150 KHz
Interfaces
Modem/MXP M&C Interface
OpenAMIP & Legacy
Network Interface
4-port managed fast ethernet switch
User Interface
Web Browser/Console Port
Motor Driver Enclosure
Connectors
Drive
DA-15P
Home
DE-9S
AZ
DA-15S
EL
DA-15S
CL
DA-15S
Status LEDs
CL Drive
Yes
EL Drive
Yes
Az Drive
Yes
MDE Status
Yes
Interface Connections
Connection
Dual Channel Rotary Joint
Power Requirements
ADE
180-265 VAC, 47-63Hz, single phase, 25W BUC=690W
Watts, 40W BUC=825 Watts (wattage includes power
consumption of brake release, pedestal drive and BUC).
12-5
6012-71 Installation Manual
Series 6012-71 C-Band Technical Specifications
Radome Assembly (81 Inch) w/
base frame
Type
Standard
Material
DIVINYCELL H100
Size
Diameter
2.05m / 80.8"
Height
1.9m / 75" W/O base frame
Base Frame Height
0.55m / 21.75 in
Hatch Size
45.7 x 71.7cm / 18 x 28 inch
Radome Weight
158.76 Kgs / 350 lbs
Base Frame weight
140.16 Kgs / 309 Lbs
RF attenuation
Typical 0.5 dB
Withstand relative average winds up to 56m/sec (125 MPH)
from any direction.
IP 56
Wind:
Ingress Protection Rating
ADE Environmental Conditions
Temperature Range (Operating)
-25 to +55 Celsius (-13 to +131 F)
Humidity
100% Condensing
Wind Speed
56 m/sec (125 mph)
Solar Radiation
1,120 Watts per square meter, 55 Celsius
Spray
Resistant to water penetration sprayed from any direction.
Icing
Survive ice loads of 4.5 pounds per square foot. Degraded
RF performance will occur under icing conditions.
Up to 101.6mm (4 inches) per hour. Degraded RF
performance may occur when the radome surface is wet.
Parts are corrosion resistant or are treated to endure effects
of salt air and salt spray. The equipment is specifically
designed and manufactured for marine use.
Rain
Corrosion
Mechanical Conditions
Systematic Vibration
Amplitude (single peak)
Acceleration
Frequency Range
5.0 millimeters
2.0 G (20m/s2)
1Hz - 150Hz
Shock (Transient Vibration)
Response Spectrum
Peak Accel., m/s2
Duration, ms
II
III
100 - 300 - 500
11 -
Number of Cycles
3 each direction
Directional Changes
12-6
Series 6012-71 C-Band Technical Specifications
6012-71 Installation Manual
Shock (Bump)
Peak Accel., m/s2
250
Duration, ms
Number of Cycles
100 ea. direction
Directional Changes
Transit Conditions
Drop (Transit Shock)
Complies with ISTA Standard
Chemically Active Substances
Environmental Condition
Test Level
Sea Salt
5 percent solution
Below Decks Equipment
Media Xchange Point (MXP)
Standard 19 Inch Rack mount
Physical Dimensions
Input Voltage
Weight
Synchro Interface
Connectors
Input Voltage Level
Synchro Ratios
Impedance
SBS Interface
Connectors
Input Voltage Level
Interface
Polarity
Ratio
Impedance
One Unit High
17 X 17 X 1.75 (Inches)/ 43.18 x 43.18 x 4.45 (cm)
85-264 VAC, 47-63Hz, single phase, 110 Watts
6.6lbs/ 3.0 kgs
5 screw terminal connections (Plug-In)
36-110 VDC, 400 or 60 Hz
1:1, 36:1, 90 or 180:1 and 360:1 with Synchro-Digital
converter
1M ohm
4 screw terminal connections (Plug-In)
20-90 VDC
Opto-isolated
Auto switching
6 steps per degree
10K Ohm
12-7
6012-71 Installation Manual
MXP Box Connections
Connections
MXP
Synchro Interface
Connectors
Input Voltage Level
Synchro Ratios
Impedance
SBS Interface
Connectors
Input Voltage Level
Interface
Polarity
Ratio
Impedance
NMEA Interface
Connections
Rx Sentence Format
Tx Sentence Format
Series 6012-71 C-Band Technical Specifications
4 Ethernet Port Back (RJ)
1 Ethernet Ports Internal (RJ)
1 Power Input
1 SMA Connector (RX from Rotary Joint to Diplexer)
1 F-Connector from Diplexer to Modem RX Port
4 Modem LEDs (On the MXP Board)
2 MXP status LEDs
Small Form Factor Pluggable
USB Devise (Mini B)
USB Host (Type A)
4 RS-232 Serial Pass thru Ports (1 Port will have the ability
to monitor receiver lock and drive transmit mute for Sat
Modem)
1 NMEA RS-232 Serial Port
1 RS-232 Console Port
1 Internal Facing RS-232 Port
SBS Gyro (TMS)
NMEA 0183
5 screw terminal connections
36-110 VDC, 400 or 60 Hz
1:1, 36:1, 90 or 180:1 and 360:1 with Synchro-Digital
converter
1M ohm
4 screw terminall connections
20-90 VDC
Opto-isolated
Auto switching
6 steps per degree
10K Ohm
5 screw termninal connections (RXA+ /RXA- input, RXB+/
RXB- input, and TXA+ output)
Global Positioning System
$xxGLL,DDmm,mmmm,N,DDDmm.mmmm,W (UTC optional)
(*CS optional)
Heading $xxHDT,xxx.x
Global Positioning System
$GPGGA,0,DDmm,N,DDDmm,W
NMEA string examples:
RX:
$GPGLL,3800.4300,N,12202.6407,W,231110,A*32
$GPGGA,231110,3800.4300,N,12202.6407,W,2,08,1.2,40.0,M,-31.3,M,,*4A
TX:
$GPRMC,231325,A,3800.4300,N,12202.6405,W,000.0,184.9,190412,014.1,E*67
$GPVTG,184.9,T,170.8,M,000.0,N,0000.0,K*74
12-8
Series 6012-71 C-Band Technical Specifications
6012-71 Installation Manual
BDE Environmental Conditions
Temperature
Humidity
0 to 40 degrees C
Up to 100% @ 40 degrees C, Non-Condensing
Power Requirements (MXP)
BDE
85-264 VAC, 47-63Hz, single phase, 100 Watts
Power Requirements (DAC)
BDE
85-264 VAC, 47-63Hz, single phase, 160 Watts max
BDE Environmental Conditions
Temperature
Humidity
0 to 40 degrees C
Up to 100% @ 40 degrees C, Non-Condensing
Regulatory Compliance
Survival Shock and Vibration
Operational Shock and Vibration
EMI/EMC Compliance Ku-Band
Satellite Earth Stations and System
(SES)
Safety Compliance
Environmental Compliance
FCC ESV Compliance C-Band
FCC ESV Compliance Ku-Band
FCC ESV Compliance Ka-Band
Options
IEC-60721, MIL-STD-901D
Operational: IEC-60945, Survival: IEC-60721 and MIL-STD
901D
MIL-STD-167-1
ETSI EN 301 843-1 V1.4.1 (2004-06)
ETSI EN 301 489-1 V1.4.1 (2002-08)
ETSI EN 300 339 (1998-03)
IEC EN 60945:1997
ETSI EN 301 428-1 V1.3.1 (2006-02)
ETSI EN 302 340 V1.1.1 (2006-04)
IEC EN 60950-1:2001 (1st Edition)
RoHS
Green Passport
47 C.F.R. 25.221
47 C.F.R. 25.222
47 C.F.R. 25.138 (FSS)
Bluetooth
12-9
