Scribd
Upload
90 views

Microcontroller Implementation of Single Phase Inverter Switching Strategies

1) The document summarizes a conference paper on implementing single-phase inverter switching strategies using a microcontroller. 2) It describes using a microcontroller to generate sinusoidal pulse width modulation pulses to control the inverter, offering flexibility to change control algorithms in software without hardware changes. 3) Experimental results show the relationship between amplitude modulation ratio, total harmonic distortion, and dead time period for different modulation schemes implemented using the microcontroller.

Uploaded by

Nz225
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
90 views

Microcontroller Implementation of Single Phase Inverter Switching Strategies

1) The document summarizes a conference paper on implementing single-phase inverter switching strategies using a microcontroller. 2) It describes using a microcontroller to generate sinusoidal pulse width modulation pulses to control the inverter, offering flexibility to change control algorithms in software without hardware changes. 3) Experimental results show the relationship between amplitude modulation ratio, total harmonic distortion, and dead time period for different modulation schemes implemented using the microcontroller.

Uploaded by

Nz225
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),

Johor Bahru, Johor, Malaysia, May 28-29, 2007

MICROCONTROLLER IMPLEMENTATION OF SINGLE PHASE


INVERTER SWITCHING STRATEGIES

B. Ismail, S. Taib, M. Isa, I. Daut, A.R Mohd Saad , F. Fauzy


School of electrical system engineering, UniMAP
Blok A, kompleks pusat pengajian, Jalan Kangar-Arau, 02600 Arau Perlis
CETREE, Komplek Eureka, USM, 11800 Pulau Pinang.
Engineering Centre, UniMAP
[email protected], [email protected]

a carrier signal is compared with the sinusoidal wave,


whose frequency is the desired frequency.
The proposed alternative approach is to replace the
conventional method with the use of microcontroller.
The use of the microcontroller brings the flexibility to
change the real-time control algorithms without further
changes in hardware. It is also need low cost and has a
small size of control circuit for the single phase bridge
inverter.
To achieve the control system an Atmel
AT89C2051-24PI microcontroller was used. The atmel
AT89C2051-24PI is a low voltage, high performance
CMOS 8-bit microcomputer with 2K bytes of Flash
programmable and erasable read only memory
(PEROM). The device is manufactured using Atmels
high density nonvolatile memory technology and is
compatible with the industry standard MCS-51
instruction set. It also has two 16-bit timers that deliver
the function use in this application. By combining a
versatile 8 bit CPU with Flash on a monolithic chip, the
Atmel AT89C2051 is powerful microcomputer with
provides a highly flexible and cost effective solution to
many embedded control applications.

Abstract
This paper presents the practical microcontroller
implementation of single phase inverter switching
strategies. The attractiveness of this configuration is the
used of a microcontroller to generate sinusoidal pulse
width modulation (SPWM) pulses. The difference
amplitude modulation ratio ma starting from 0.3 until
over modulation with 2 KHz switching frequency was
implemented and tested. Selected results from the
experimental prototype will be presented. The result
shows the relationship between amplitude modulation
ratio with total harmonic distortion (THD) and dead
time period.

1. Introduction
SPWM or sinusoidal pulse width modulation is
widely used in power electronics to digitize the power
so that a sequence of voltage pulses can be generated by
the on and off of the power switches. The pulse width
modulation inverter has been the main choice in power
electronic for decades, because of its circuit simplicity
and rugged control scheme [1]. SPWM switching
technique is commonly used in industrial applications.
SPWM techniques are characterized by constant
amplitude pulses with different duty cycle for each
period. The width of this pulses are modulated to obtain
inverter output voltage control and to reduce its
harmonic content [2]. Sinusoidal pulse width
modulation or SPWM is the mostly used method in
motor control and inverter application. In this
development a unipolar SPWM voltage modulation
type [3]-[4] is selected because this method offers the
advantage of effectively doubling the switching
frequency of the inverter voltage, thus making the
output filter smaller, cheaper and easier to implement.
Conventionally, to generate this signal, triangle wave as

2. Pulse Width Modulation Control


The frequency modulation ratio mf is defined as the
ratio of the frequencies of the carrier and the reference
signals which is written as

mf =

fcarrier
freference

ftri
f sin

(1)

The amplitude modulation ratio ma is define as the


ratio of the amplitude of the reference and carrier
signals and is given by

104

International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),


Johor Bahru, Johor, Malaysia, May 28-29, 2007

ma =

Vm, reference
Vm, sin
=
Vm, carrier
Vm, carrier

carrier signal and reference signal and the gating pulses


signal (Vg).

(2)

The amplitude of the PWM of the fundamental


frequency output is controlled by ma . This is
significant for an unregulated DC voltage because the
value of ma can be adjusted to compensate the
variations in the DC voltage, thus producing a constant
amplitude output. If ma is greater than 1 or over
modulation, the amplitude of the output increases with
ma , but not linearly.

3. Approach and Method


Figure 1 below show the full bridge single phase
inverter and its switching strategy.

Figure 2: Strategy control of the switching technique

Figure 1: Single phase full bridge inverter

Figure 2 shows the strategy control of the switching


technique for the inverter. The gS1, gS2, gS3 and gS4
are output gating signal for power switchers S1, S2, S3
and S4 respectively. Figure 2a shows the comparing
signal between carrier signal and reference signal.
While figure 2b shows the pulse for the power
switchers and figure 2c shows the output of the inverter.
In this development every pulses for gS1, gS2, gS3 and
gS4 was programmed by using microcontroller. The
size of the pulses is depended on the comparison
between carrier signal and reference signal. When the
amplitude modulation ratio ( ma ) is difference, the size
of the pulse also difference. Both gating signal (gS1 and
gS3) and (gS2 and gS4) used the same control signal
generated by the microcontroller. The different is only
(gS1 and gS3) signal is leading (gS2 and gS4) by half
cycle or 180 degree of the switching signal. Figure 3
below clearly illustrated the comparison signal between

Figure 3: Comparison signal and gating pulses signal

4. Experimental Results and Discussion


The selected results have been chosen to illustrate
some of the main features of microcontroller SPWM
control, which have been presented in this paper. Figure
4 shows the switching signal for difference amplitude
modulation ratio, started from 0.3 until 1.5. Figure 5
shows the output voltage and current for single phase
inverter after the filter with amplitude modulation is
1.3.

105

International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),


Johor Bahru, Johor, Malaysia, May 28-29, 2007

(a)

(f)

(b)

(g)

(c)

(h)

(i)
(d)

(j)
(e)
Figure 4: Switching signal for difference amplitude modulation ratio
(a)

ma =0.3, (b) ma =0.4, (c) ma =0.5, (d) ma =0.6, (e) ma =0.7, (f) ma =0.8, (g) ma =0.9, (h) ma =1.0,
( i ) ma =1.3, ( j ) ma =1.5
X-axis: 1div= 1ms, Y-axis: 1div=2V

106

International Conference on Control, Instrumentation and Mechatronics Engineering (CIM '07),


Johor Bahru, Johor, Malaysia, May 28-29, 2007

5. Conclusion
The main task in this work is to find the best
switching pulses generated by microcontroller with
difference amplitude modulation ratio. Amplitude
modulation ratio, ma =1.3 produced good total
harmonic distortion for both voltage and current. THD
produced by that signal is less than 3% (after filter).
The implementation of the single phase SPWM
switching signal using microcontroller is placed on
minimization of the hardware requirement, with as
many functions as possible being performed in the
software. Using microcontroller unit, the amplitude
modulation ratio and duty cycle can be easily change
through programming without further hardware
changes.

Figure 5: Output of the inverter after filter with resistive load


for ma =1.3 (100V/div), (1A/div)

A comparison of the total harmonic distortion


(THD) for difference amplitude modulation ratio shows
that the total harmonic distortion increase started from
ma =0.3 until ma =0.6. Total harmonic distortion for
ma =0.7 to ma =1.3 is decrease when the amplitude
modulation is increase and THD increase back when
amplitude modulation ratio, ma =1.5. This can be seen
in Figure 6. A comparison of the dead time period for
difference amplitude modulation ratio shows that the
dead time period decreases when ma is increase. This
can be seen in Figure 7.

6. References
[1] B. Ismail, S.Taib, A.R Mohd Saad, M.Isa, I.Daut.
Development of Control Circuit for Single Phase
Inverter Using Atmel Microcontroller, Proc. Of the
International Conference of Man-Manchine System,
Langkawi, 2006.
[2] B. Ismail, S.Taib, A.R Mohd Saad, M.Isa, C.M
Hadzer. Development of a Single Phase SPWM
Microcontroller-Based Inverter, Proc.of the First
International Power and Energy Conference, PECon
2006, Putrajaya, pp 437-440.
[3] L. Mihalache. DSP Control Method of Single
Phase Inverters for UPS Applications. IEEE Trans. On
Industry Application. 2002, pp 590-595.
[4] N. Mohan, T.M.Undeland, W.P.Robbins, Power
Electronic-Converters, Applications and Design,
Second edition, John Wiley & Sons Inc., 1995.

Figure 6: THD versus amplitude modulation ratio

Figure 7: Dead time period versus amplitude modulation ratio

107

You might also like