Scribd
Upload
67 views

Basic Comp

This document provides an introduction to common electronic components used in building a motor speed controller. It describes resistors and how they control current and voltage through Ohm's law. It also covers capacitors and how they store electrical energy, diodes and how they allow current to flow in one direction, transistors and how they amplify and switch signals, integrated circuits and how they use transistors to perform computational tasks, and other components like light emitting diodes, potentiometers, and printed circuit boards. The overall purpose is to give the reader a basic understanding of how these components work together in a motor speed controller to allow control of a motor's speed and direction.

Uploaded by

itamar_123
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
67 views

Basic Comp

This document provides an introduction to common electronic components used in building a motor speed controller. It describes resistors and how they control current and voltage through Ohm's law. It also covers capacitors and how they store electrical energy, diodes and how they allow current to flow in one direction, transistors and how they amplify and switch signals, integrated circuits and how they use transistors to perform computational tasks, and other components like light emitting diodes, potentiometers, and printed circuit boards. The overall purpose is to give the reader a basic understanding of how these components work together in a motor speed controller to allow control of a motor's speed and direction.

Uploaded by

itamar_123
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 27

An introduction to electronic components that you

will need to build a motor speed controller.

Resistors
A resistor impedes the flow of electricity through a circuit.
Resistors have a set value.
Since voltage, current and resistance are related through Ohms
law, resistors are a good way to control voltage and current in
your circuit.

More on resistors
Resistor color codes

1st band =
2nd band =
3rd band =
4th band =

1st number
2nd number
# of zeros / multiplier
tolerance

Color code
Tolerance: Gold = within 5%

Black: 0
Brown: 1
Red: 2
Orange: 3
Yellow: 4
Green: 5
Blue: 6
Violet: 7
Gray: 8
White: 9
4

Units
Knowing your units is important!
Kilo and Mega are common in resistors
Milli, micro, nano and pico can be used in other

components
K (kilo) = 1,000
M (mega) = 1,000,000
M (milli) = 1/1,000
u (micro) = 1/1,000,000
n (nano) = 1/1,000,000,000 (one trillionth)
p (pico) = 1 / 1,000,000,000,000 (one quadrillionth)
5

Capacitors
A capacitor stores electrical energy.
This pool of electrons is available for electronic components to
use.
Capacitance is measured in Farads. The small capacitors usually used in
electronics are often measured in microfarads and nanofarads.

Some capacitors are polarized. Note the


different length terminals on one of the capacitors.
6

Polarity of capacitors
The shorter terminal goes

on the negative side.


The stripe is on the
negative terminal side of
the capacitor.
The board is marked for

positive or negative.

Applications of capacitors
Capacitors supply a pool of electrons for immediate use.

If a component needs an immediate supply of electrons, the


capacitor can supply those electrons.

Capacitors can smooth out a signal eliminate the ripples

or spikes in DC voltage.

The capacitor can absorb the peaks and fill in the


valleys of a rippled signal.
8

Diode
A diode is a one way valve (or gate) for electricity. It is a

component with an asymmetrical transfer characteristic. A


diode has low (ideally zero) resistance in one direction, and
high (ideally infinite) resistance in the other direction.

Diodes will protect your electronics.


9

Diode circuit protection


In a DPDT switch, if polarity is wrong, the motor will run

backwards.
In an electronic circuit, if the polarity is wrong, you can fry
your components.
A diode in your system will help to prevent problems.

Diodes have a bar


on the cathode
(negative) side.

10

Light emitting diode (LED)


A light emitting diode (LED) is a semiconductor light source.

When electricity is passing through the diode, it emits light.

Jeremy is going to talk a lot more about LEDs.


11

Variable resistor / Potentiometer


A potentiometer is a variable resistor. As you manually

turn a dial, the resistance changes.

12

How a variable resistor works


As the dial/wiper turns, electricity must go through

more or less of the resistive strip.


In series, the change in resistance means a change in voltage.

So as you turn the

dial/wiper, you get


a change in voltage.

13

Transistors
A transistor is a semiconductor device used to amplify

and switch electronic signals and electrical power.

This is our electronic switch!


14

How a transistor works


A voltage or current applied to one pair of the

transistors terminals changes the current through


another pair of terminals.
A transistor is composed of semiconductor material
with at least three terminals
for connection to an external
circuit.
Transistors have 3 pins.
For these transistors:
Collector
Emitter
Base
15

Terminology
BJT versus FET
Bipolar junction transistor. Useful as amplifiers.
Collector, Emitter, Base
Field-effect transistor. Useful as motor drivers.

Source, Drain, Gate


MOSFET: Metal-oxide-semiconductor FET

NPN (N-channel FET) versus PNP (P-channel FET)


NPN versus PNP is how the semiconductors are layered.
NPN: Not pointing in
PNP: Pointing in permanently
16

Schematic symbols

BJT PNP

P-channel FET

BJT NPN

N-channel FET
17

Integrated circuit
An integrated circuit (IC) is a set of transistors that is

the controller or brain of an electronic circuit.


An input is received, an output is sent out.

Modern microprocessor ICs can have billions of


transistors per square inch!
18

What an IC can do for us?


Billions of electronically controlled on/off switches

(transistors) is how the microprocessor in a digital


computer thinks and functions.

A computer has a wide range of tasks to perform.

But other ICs can complete simpler, discrete jobs.


For example, an IC can take a voltage input and output
commands to a motor.

19

IC Terminology: Op-amp
An operational amplifier (op-amp) is a set of

transistors inside the integrated circuit. They often are


the components doing the mathematical operations.

20

H-bridge
An electronic circuit that enables voltage to be applied

across a load in either direction.

A DPDT switch also does this, but not electronically.


21

H-bridge
Need four electronic switches.
Either have 1 and 4 closed. Or 2 and 3 closed.

What happens if both 1 and 2 are closed?


The H-bridge allows electricity to flow both ways across the motor,

which gives us forward and reverse.


We can use pulse width modulation to control how often the
switches are on versus off, which gives us speed control.
22

Varying voltage
A potentiometer/variable resistor allows you to

change the voltage input that goes into the integrated


circuit.

Integrated circuit can now output variety of pulse widths

to the transistors on the H-bridge.


This combination of potentiometer, integrated circuit and
PWM to the H-bridge is the key to speed control.
23

Why not skip the IC?


There are a couple reasons we dont use just a

potentiometer to control the speed of our motors.


Potentiometers are rarely used to control significant power (more

than a watt).
You would still need a way to switch the direction of the motor. Just

using a potentiometer can control speed, but not direction.


DPDT switch and potentiometer combinations can lead to
problems if you quickly switch from full forward to full reverse.
Problems can occur if the polarity of a spinning DC motor gets
suddenly switched from forward to reverse.

Current surge
Mechanical stress
24

Printed Circuit Board


Components are attached to a printed

circuit board.
The front side of the board will have
printed component information, such
as resistor # and resistance, diode type
and polarity, etc.
Holes go all the way through the board
from one side to the other. Throughhole soldering is needed to connect
components to the board.

25

Back of Circuit Board


The back side of the board will have lines indicating

connections between components. The lines on the


back are similar to wires.
Thicker lines denote more current (electrons) moving
through.
Components connect the lines.

26

Conclusion

Hopefully that wasnt too

confusing.

The goal was to give you a basic


understanding of how some of the
electronic components of a motor
speed controller work.
There are lots of tools to help you
with the basics.

27

You might also like