Scribd
Upload
174 views

Collision Lab Guide

This document provides tips for using the PhET Collision Lab simulation, including: - Controls like changing velocities by dragging vectors and pausing/stepping simulations - Displays like the momentum graph and kinetic energy - Parameters like elasticity and reflecting borders - Student misconceptions around energy loss during inelastic collisions - Suggestions for activities like exploring explosions by setting total initial momentum to zero - Resources for using PhET simulations in teaching and developing activities

Uploaded by

Nesty Prianti Nababan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
174 views

Collision Lab Guide

This document provides tips for using the PhET Collision Lab simulation, including: - Controls like changing velocities by dragging vectors and pausing/stepping simulations - Displays like the momentum graph and kinetic energy - Parameters like elasticity and reflecting borders - Student misconceptions around energy loss during inelastic collisions - Suggestions for activities like exploring explosions by setting total initial momentum to zero - Resources for using PhET simulations in teaching and developing activities

Uploaded by

Nesty Prianti Nababan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

PhET Tips for Teachers

Collision Lab New version in 2012!

Tips for controls:


The velocities are changeable by grabbing the green vectors. When the velocity vector becomes

too small to see, a dark circle appears on the ball. The circle
is grabbable to change the
velocity.
The balls location can be changed by grabbing the balls.
The Momentum graph is a display of the momentum. You cannot change the momentum vectors
using the graph, only by changing the mass or velocity.
Turning off Reflecting Borders enables students to focus on ball- ball collisions which do
conserve Momentum. Ball-wall collisions do not conserve momentum
Mechanical energy changes can be determined using the Kinetic Energy display.
Elasticity affects the ball-wall and ball-ball collisions.
You can Pause the sim and then use Step to incrementally analyze. The Back button only
functions for perfectly elastic collisions, so it is disabled if the elasticity is less than 100%.
If you are doing a lecture demonstration, set your screen resolution to 1024x768 so the simulation
will fill the screen and be seen easily.
Tip-to-Tail can be unchecked to enable more understanding about vectors
because the students can translate the vectors.

Important modeling notes / simplifications:


Time step is variable according to Sim Speed slider
The balls are non-rotating.
In one dimension, the vectors are not technically tip-to-tail: the vectors are offset, so
that the students can see the vectors more easily.
The More Data section can be useful after qualitative investigations to design specific
experiments by typing in the table.
Insights into student use / thinking:
Students preferred to start the sim in one dimension and with no walls. The new first tab
implements this as the default.
Students may be surprised that when the Elasticity to less than 100%, they see
the Kinetic Energy decrease after each collision.
The vector representations in the Momentum diagram can extend beyond the grid.
Students can use the zoom control to resize the vectors so they fit in the box.

Suggestions for sim use:


Explosions can be explored by setting the balls next to
one another and adjusting initial velocities so that the
initial total momentum is zero.
For tips on using PhET sims with your students see:
Guidelines for Inquiry Contributions and Using PhET Sims
The simulations have been used successfully with homework, lectures, in-class activities, or lab
activities. Use them for introduction to concepts, learning new concepts, reinforcement of
concepts, as visual aids for interactive demonstrations, or with in-class clicker questions. To read
more, see Teaching Physics using PhET Simulations and Teacher Ideas & Activities

Written by Trish Loeblein, Mike Dubson, Mindy Gratny last updated Jun 2012

PhET Tips for Teachers

Collision Lab New version in 2012!

For Experts: Elasticity, a number between 0 and 1, indicates the amount of kinetic energy lost during
collisions. If the elasticity = 1, the collision is perfectly elastic, and kinetic energy is conserved.
Elasticity < 1 affects the magnitude of the component of the velocity along the line of action
between two colliding balls. The line of action is the line connecting the centers of the balls at the
moment of collision. If the elasticity is, say, 0.3, then the speed along the line of action after collision
is 0.3 of the value it would have had in an elastic collision. The speed perpendicular to the line of
action is not affected. Since these balls are non-rotating, changing the speed perpendicular to the line
of action would violate Conservation of Angular Momentum.

Written by Trish Loeblein, Mike Dubson, Mindy Gratny last updated Jun 2012

You might also like