The Signaling connection Setup Procedure is performed to exchange the NAS(Non-Access Stratum
between the UE & the Core Network (CN).
Triggering Condition The UE sends direct transfer message to initiate the signaling connection setup
The Authentication & Security mode control procedure is performed for the UE and the network t
implement bi-directional
Authentication and negotiate and configure the integrity protection algorithm and ciphering algorithm. t
procedure ensures
Integrity and correctness of signaling.
Triggering Condition The UE and CN exchange signaling. The Network initiates the authentication an
security mode control
Procedure.
The Call Set up Procedure is performed to set a call
Triggering Condition The UE initiates a Call.
The Call Release Procedure is performed to release services and resources after a call ends.
Triggering Condition A call ends and the calling party hang ups.
RRC Connection Set up procedure is performed for the UE to set up a signaling connection to the RNC.RRC Connection
Setup is always initiated by the UE. One UE has a maximum of one RRC connection at a time .
Triggering Condition The UE in idle mode initiates the RRC connection set up procedure when the NAS of the UE
Request the establishment of signaling connection. When the RNC receives an RRC CONNECTION REQUEST message from
The UE the Radio Resource Management(RRM) module of the RNC determines whether to accept or reject the RRC connecti
request ,based on the specific algorithm. If accepting the request the RMM module further determines whether to setup
The RRC connection on a Dedicated Channel(DCH) or Common Channel (CCH) based on the specific RRM algorithm .typical
An RRC connection is setup on the DCH
The Signaling connection Setup Procedure is performed to exchange the NAS(Non-Access Stratum) information
between the UE & the Core Network (CN).
Triggering Condition The UE sends direct transfer message to initiate the signaling connection setup procedure
The Authentication & Security mode control procedure is performed for the UE and the network to
implement bi-directional
Authentication and negotiate and configure the integrity protection algorithm and ciphering algorithm. this
procedure ensures
Integrity and correctness of signaling.
Triggering Condition The UE and CN exchange signaling. The Network initiates the authentication and
security mode control
Procedure.
The Call Set up Procedure is performed to set a call
Triggering Condition The UE initiates a Call.
The Call Release Procedure is performed to release services and resources after a call ends.
Triggering Condition A call ends and the calling party hang ups.
RRC Connection Release Procedure is performed to release signaling connection and all radio bearers between UE
And the UTRAN.
Triggering Condition After the RAB is release the RNC judge whether the RRC connection carries any other RAB or the U
If judging the RRC connection does not carry other RAB of the UE the RNC initiates as a RRC connection release procedure.
RRC Connection Release Procedure is performed to release signaling connection and all radio bearers between UE
And the UTRAN.
Triggering Condition After the RAB is release the RNC judge whether the RRC connection carries any other RAB or the U
If judging the RRC connection does not carry other RAB of the UE the RNC initiates as a RRC connection release procedure.
RRC:RRC Connection Request (RACH)
RRC:RRC Connection Setup (FACH)
RRC:RRC Connection Setup Complete (DCCH)
RRC: Initial Direct Transfer (MM: CM Service Request)
RACH)
ACH)
te (DCCH)
vice Request)
RANAP:Initial UE Message (MM: CM Service Request)
RANAP: Direct Transfer (MM: Authentication Request)
RRC: Downlink Direct Transfer (MM: Authentication Request)
RRC: Uplink Direct Transfer (MM: Authentication Response)
RANAP: Direct Transfer (MM: Authentication Response)
RRC: Security Mode Command
RRC: Security Mode Complete
RANAP: Direct Transfer (CC: Setup)
RRC: Uplink Direct Transfer (CC: Setup)
RRC: Downlink Direct Transfer (CC: Call Proceeding)
RANAP: Direct Transfer (CC: Call Proceeding)
RRC: Radio Bearer Setup
RRC: Radio Bearer Setup Complete
RANAP: Direct Transfer (CC: Alerting)
RRC: Downlink Direct Transfer (CC: Alerting)
RANAP: Direct Transfer (CC: Connect)
RRC: Downlink Direct Transfer (CC: Connect)
RANAP: Direct Transfer (CC: Connect Acknowledge)
RRC: Uplink Direct Transfer (CC: Connect Acknowledge)
RANAP: Direct Transfer (CC: Disconnect)
RRC: Uplink Direct Transfer (CC: Disconnect)
RANAP: Direct Transfer (CC: Release)
RRC: Downlink Direct Transfer (CC: Release)
RANAP: Direct Transfer (CC: Release Complete)
RRC: Uplink Direct Transfer (CC: Release Complete)
RRC: Downlink Direct Transfer (CC: RRC Connection Release)
RRC: Uplink Direct Transfer (CC: RRC Connection Release Complete)
>>"RRC Connection Request Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(5)=5 , hex2dec(2)=2 ,hex2dec(0)=0 --> MCC=520
value=hex2dec(0)=0 , hex2dec(1)=1 --> MNC=01
value=hex2dec(2908)= 10504
value= OriginatingConversationalcall (CS MOC)
value=(-24+ (43/2))=-2.5 dB
value=hex2dec(60)=96(Neighbour's Primary Scrambling Code)
value=CPICH Ec/Io invalid
>>"RRC Connection Setup Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(5)=5 , hex2dec(2)=2 ,hex2dec(0)=0 --> MCC=520
value=hex2dec(0)=0 , hex2dec(1)=1 --> MNC=01
value=hex2dec(2908)= 10504
value=UE capable to support FDD , not TDD
value=UE capable to support GSM
value=Signaling Radio Bearer Information Setup ,RB-1
value=Radio Bearer Mapping
value=Signaling Radio Bearer Information Setup ,RB-2
value=Signaling Radio Bearer Information Setup ,RB-3
value=Signaling Radio Bearer Information Setup ,RB-4
value=BLER Target= -20 dB
value=MaxAllowedULTxPower=24 dBm
value=(-47*2)= -94 dBm (step of 2 dB)
value= use Closed Loop Power Control Algorithm1
value= use long SC on Uplink
value=Spreading Factor 64 (Uplink)
value=Spreading Factor 128 (Downlink)
value=Primary Scrambling code=97
value=Spreading Factor 128 (Downlink)
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000010110111011110010010 => RNCid=bin2dec(000000001011)=11 and Cellid=bin2dec(0111011110010010)=30610
>>"RRC Connection Setup Complete Description"
value= not support GSM (Locked UMTS Mode)
value= Chipering Algorithm A5/3
value= UE support Band fdd2100 MHz
value= UE (Powerclass3) maximum transmitted power =24 dBm
value= support Compressed Mode (CM) uplink and downlink
value= UE support Band fdd1800 MHz
ANAP:Initial UE Message (MM: CM Service Request)
ANAP: Direct Transfer (MM: Authentication Request)
Downlink Direct Transfer (MM: Authentication Request)
Uplink Direct Transfer (MM: Authentication Response)
NAP: Direct Transfer (MM: Authentication Response)
RRC: Security Mode Command
RRC: Security Mode Complete
RANAP: Direct Transfer (CC: Setup)
RRC: Uplink Direct Transfer (CC: Setup)
RC: Downlink Direct Transfer (CC: Call Proceeding)
RANAP: Direct Transfer (CC: Call Proceeding)
RRC: Radio Bearer Setup
RRC: Radio Bearer Setup Complete
RANAP: Direct Transfer (CC: Alerting)
RRC: Downlink Direct Transfer (CC: Alerting)
RANAP: Direct Transfer (CC: Connect)
RRC: Downlink Direct Transfer (CC: Connect)
ANAP: Direct Transfer (CC: Connect Acknowledge)
C: Uplink Direct Transfer (CC: Connect Acknowledge)
RANAP: Direct Transfer (CC: Disconnect)
RRC: Uplink Direct Transfer (CC: Disconnect)
RANAP: Direct Transfer (CC: Release)
RRC: Downlink Direct Transfer (CC: Release)
RANAP: Direct Transfer (CC: Release Complete)
RC: Uplink Direct Transfer (CC: Release Complete)
Downlink Direct Transfer (CC: RRC Connection Release)
nk Direct Transfer (CC: RRC Connection Release Complete)
value= Call B-Party number = 0812713339
>>"Radio Bearer Description"
value= SF64(uplink)-> AMR 12.2
value=Primary Scrambling code=97
value= SF128(downlink)-> AMR 12.2
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000010110111011110010010 => RNCid=bin2dec(000000001011)=11 and Cellid=bin2dec(0111011110010010)=30610
Default Constant
-22
-22
Note :DPCCH_Power_offset is configured by RNC and delivered to UE in RRC Connection Setup.
DPCCH_Power_offset
CPICH_RSCP
PCPICH Power
UL Interference
-94
-80
33
-105
-94
-70
33
-105
UL DPCCH Initial Power
-14
-24
Paging Procedure is performed when the CN calls a UE.
Triggering Condition A terminals call the UE.
RRC Connection Set up procedure is performed for the UE to set up a signaling connection
Setup is always initiated by the UE. One UE has a maximum of one RRC connection at a time .
Triggering Condition The UE in idle mode initiates the RRC connection set up procedure wh
Request the establishment of signaling connection. When the RNC receives an RRC CONNECTIO
The UE the Radio Resource Management(RRM) module of the RNC determines whether to acce
request ,based on the specific algorithm. If accepting the request the RMM module further det
The RRC connection on a Dedicated Channel(DCH) or Common Channel (CCH) based on the sp
An RRC connection is setup on the DCH
The Signaling connection Setup Procedure is performed to exchange the NAS(Non-Access
between the UE & the Core Network (CN).
Triggering Condition The UE sends direct transfer message to initiate the signaling connecti
The Authentication & Security mode control procedure is performed for the UE and the n
Authentication and negotiate and configure the integrity protection algorithm and ciphering algo
Integrity and correctness of signaling.
Triggering Condition The UE and CN exchange signaling. The Network initiates the authentic
Procedure.
The Call Set up Procedure is performed to set a call
Triggering Condition The UE initiates a Call.
The Call Release Procedure is performed to release services and resources after a call ends.
Triggering Condition A call ends and the calling party hang ups.
RRC Connection Release Procedure is performed to release signaling connection and all rad
And the UTRAN.
Triggering Condition After the RAB is release the RNC judge whether the RRC connection ca
If judging the RRC connection does not carry other RAB of the UE the RNC initiates as a RRC con
set up a signaling connection to the RNC.RRC Connection
ne RRC connection at a time .
nnection set up procedure when the NAS of the UE
C receives an RRC CONNECTION REQUEST message from
C determines whether to accept or reject the RRC connection
t the RMM module further determines whether to setup
hannel (CCH) based on the specific RRM algorithm .typically
xchange the NAS(Non-Access Stratum) information
initiate the signaling connection setup procedure
erformed for the UE and the network to implement bi-directional
n algorithm and ciphering algorithm. this procedure ensures
Network initiates the authentication and security mode control
nd resources after a call ends.
s.
gnaling connection and all radio bearers between UE
hether the RRC connection carries any other RAB or the UE.
he RNC initiates as a RRC connection release procedure.
RRC: Paging Type 1
RRC: RRC Connection Request (RACH)
RRC: RRC Connection Setup (FACH)
RRC:RRC Connection Setup Complete (DCCH)
RANAP: Initial UE Message (MM: Paging Response)
RRC: Initial Direct Transfer (MM: Paging Response)
RRC: Security Mode Command
RRC: Security Mode Complete
RRC: Downlink Direct Transfer (CC: Setup)
RANAP: Direct Transfer (CC: Setup)
RANAP: Direct Transfer (CC: Call Confirmed)
RRC: Uplink Direct Transfer (CC: Call Confirmed)
RRC: Radio Bearer Setup
RRC: Radio Bearer Setup Complete
RANAP: Direct Transfer (CC: Alerting)
RRC: Uplink Direct Transfer (CC: Alerting)
RANAP: Direct Transfer (CC: Connect)
RRC: Uplink Direct Transfer (CC: Connect)
RANAP: Direct Transfer (CC: Connect Acknowledge)
RRC:Downlink Direct Transfer (CC: Connect Acknowledge)
RANAP: Direct Transfer (MM: Authentication Request)
RRC: Downlink Direct Transfer (MM: Authentication Request)
RRC: Uplink Direct Transfer (MM: Authentication Response)
RANAP: Direct Transfer (MM: Authentication Response)
RANAP: Direct Transfer (CC: Disconnect)
RRC: Downlink Direct Transfer (CC: Disconnect)
RRC: Uplink Direct Transfer (CC: Release)
RANAP: Direct Transfer (CC: Release)
RANAP: Direct Transfer (CC: Release Complete)
RRC: Uplink Direct Transfer (CC: Release Complete)
RRC: Downlink Direct Transfer (CC: RRC Connection Release)
RRC: Uplink Direct Transfer (CC: RRC Connection Release)
ge)
quest)
Request)
esponse)
ponse)
ect)
ete)
plete)
n Release)
Release)
>>"RRC Connection Request Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(5)=5 , hex2dec(2)=2 ,hex2dec(0)=0 --> MCC=520
value=hex2dec(0)=0 , hex2dec(1)=1 --> MNC=01
value=hex2dec(2908)= 10504
value= terminatingConversationalcall (CS MTC)
value=(-24+ (44/2))=-2.0 dB
value=hex2dec(6d)=109(Neighbour's Primary Scrambling Code)
value=CPICH Ec/Io invalid
>>"RRC Connection Setup Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(5)=5 , hex2dec(2)=2 ,hex2dec(0)=0 --> MCC=520
value=hex2dec(0)=0 , hex2dec(1)=1 --> MNC=01
value=hex2dec(2908)= 10504
value=UE capable to support FDD , not TDD
value=UE capable to support GSM
value=Signaling Radio Bearer Information Setup ,RB-1
value=Radio Bearer Mapping
value=Signaling Radio Bearer Information Setup ,RB-2
value=Signaling Radio Bearer Information Setup ,RB-3
value=Signaling Radio Bearer Information Setup ,RB-4
value=BLER Target= -20 dB
value=MaxAllowedULTxPower=24 dBm
value=(-48*2)= -96 dBm (step of 2 dB)
value= use Closed Loop Power Control Algorithm1
value= use long SC on Uplink
value=Spreading Factor 64 (Uplink)
value=Spreading Factor 128 (Downlink)
value=Primary Scrambling code=97
value=Spreading Factor 128 (Downlink)
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000010110111011110010010 => RNCid=bin2dec(000000001011)=11 and Cellid=bin2dec(0111011110010010)=30610
>>"RRC Connection Setup Complete Description"
value= not support GSM (Locked UMTS Mode)
value= Chipering Algorithm A5/3
value= UE support Band fdd2100 MHz
value= UE (Powerclass3) maximum transmitted power =24 dBm
value= support Compressed Mode (CM) uplink and downlink
value= Call B-Party number = 0813713339
>>"Radio Bearer Description"
value= SF64(uplink)-> AMR 12.2
value=Primary Scrambling code=97
value= SF128(downlink)-> AMR 12.2
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000010110111011110010010 => RNCid=bin2dec(000000001011)=11 and Cellid=bin2dec(0111011110010010)=30610
Default Constant
DPCCH_Power_offset
CPICH_RSCPPCPICH PowerUL Interference
UL DPCCH Initial Power
-22
-96
-80
33
-107
-16
-22
-96
-70
33
-107
-26
Note :DPCCH_Power_offset is configured by RNC and delivered to UE in RRC Connection Setu
CCH Initial Power
ed to UE in RRC Connection Setup.
RRC Connection Set up procedure is performed for the UE to set up a signaling
Setup is always initiated by the UE. One UE has a maximum of one RRC connection
Triggering Condition The UE in idle mode initiates the RRC connection set up p
Request the establishment of signaling connection. When the RNC receives an RRC
The UE the Radio Resource Management(RRM) module of the RNC determines whe
request ,based on the specific algorithm. If accepting the request the RMM module
The RRC connection on a Dedicated Channel(DCH) or Common Channel (CCH) base
An RRC connection is setup on the DCH
The PS Session Setup is performed to set up a PS session
Triggering Condition The UE sends activate PDP context request message to R
When the UE initiates a packet call setup. The UE has the state packet mobility ma
To transmit and receive data while moving within a PLMN and starts the PDP conte
And remove a virtual data channel between a terminal connected to UE and GGSN
The PS session release procedure is performed to release services after a session ends
Triggering Conditions The UE send Deactivate PDP Context request message to RNC.A
terminates a packet call. Before the deactivation ,the UE has the state active. after the PDP
becomes Packet mobility management connected. The RAB will be released if there area no
maybe initiated by a :UE procedure ,SGSN procedure,GGSN procedure.
RRC Connection Release Procedure is performed to release signaling connectio
And the UTRAN.
Triggering Condition After the RAB is release the RNC judge whether the RRC c
If judging the RRC connection does not carry other RAB of the UE the RNC initiates
RRC Connection Release Procedure is performed to release signaling connectio
And the UTRAN.
Triggering Condition After the RAB is release the RNC judge whether the RRC c
If judging the RRC connection does not carry other RAB of the UE the RNC initiates
or the UE to set up a signaling connection to the RNC.RRC Connection
ximum of one RRC connection at a time .
s the RRC connection set up procedure when the NAS of the UE
When the RNC receives an RRC CONNECTION REQUEST message from
le of the RNC determines whether to accept or reject the RRC connection
g the request the RMM module further determines whether to setup
r Common Channel (CCH) based on the specific RRM algorithm .typically
session
context request message to RNC .PDP context activation is performed
s the state packet mobility management connected that enable the user
LMN and starts the PDP context activation procedure used to setup
al connected to UE and GGSN
services after a session ends.
xt request message to RNC.A PDP Context Deactivation is performed when UE
the state active. after the PDP context deactivation procedure the state
ill be released if there area no other PDP context activated.PDP deactivation
rocedure.
to release signaling connection and all radio bearers between UE
RNC judge whether the RRC connection carries any other RAB or the UE.
AB of the UE the RNC initiates as a RRC connection release procedure.
to release signaling connection and all radio bearers between UE
RNC judge whether the RRC connection carries any other RAB or the UE.
AB of the UE the RNC initiates as a RRC connection release procedure.
RRC:RRC Connection Request (RACH)
RRC:RRC Connection Setup (FACH)
RRC:RRC Connection Setup Complete (DCCH)
RRC: Initial Direct Transfer (GMM: Service Request)
RANAP: GMM:Service Request
RRC: Security Mode Command
RRC: Security Mode Complete
RRC: Uplink Direct Transfer (SM: Activate PDP Context Request)
RANAP: SM: Activate PDP Context Request
RRC: Radio Bearer Setup
RRC: Radio Bearer Setup Complete
RANAP: SM: Activate PDP Context Accept
RRC: Downlink Direct Transfer (SM: Activate PDP Context Accept)
RRC: Physical Channel Reconfiguration (DCCH)
RRC:Physical Channel Reconfiguration Complete (DCCH)
RRC: Uplink Direct Transfer (SM: Deactivate PDP Context Request)
RANAP: SM: Deactivate PDP Context Request
RANAP: SM: Deactivate PDP Context Accept
RRC: Downlink Direct Transfer (SM: Deactivate PDP Context Accept)
RRC: Radio Bearer Release
RRC: Radio Bearer Release Completed
RRC: Downlink Direct Transfer (CC: RRC Connection Release)
RRC: Uplink Direct Transfer (CC: RRC Connection Release Complete)
>>"RRC Connection Request Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(4)=4 , hex2dec(1)=1 ,hex2dec(3)=3 --> MCC=413
value=hex2dec(0)=0 , hex2dec(1)=1 --> MNC=01
value=hex2dec(7594)= 30100
value= OriginatingBackgroundCall (PS MOC)
value=(-24+ (37/2))=-5.5 dB
value= HSDPA Release5
>>"RRC Connection Setup Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(4)=4 , hex2dec(1)=1 ,hex2dec(3)=3 --> MCC=413
value=hex2dec(0)=0 , hex2dec(1)=1 --> MNC=01
value=hex2dec(7594)= 30100
value=UE capable to support FDD , not TDD
value=UE capable to support GSM
value=Signaling Radio Bearer Information Setup ,RB-1
value=Radio Bearer Mapping
value=Signaling Radio Bearer Information Setup ,RB-2
value=Signaling Radio Bearer Information Setup ,RB-3
value=Signaling Radio Bearer Information Setup ,RB-4
value=BLER Target= -20 dB
value=MaxAllowedULTxPower=24 dBm
value=(-48*2)= -96 dBm (step of 2 dB)
Default Constant
DPCCH_Power_offset
-22
-96
-22
-96
Note :DPCCH_Power_offset is configured by RNC
value= use Closed Loop Power Control Algorithm1
value= use long SC on Uplink
value=Spreading Factor 64 (Uplink)
value=Spreading Factor 128 (Downlink)
value=Primary Scrambling code=30
value=Spreading Factor 128 (Downlink)
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000000010001010100101111 => RNCid=bin2dec(000000000001)=1 and Cellid=bin2dec(000101
>>"RRC Connection Setup Complete Description"
value=support GSM (Dual Mode GSM<>UMTS)
value= Chipering Algorithm A5/3
value= support Compressed Mode (CM) uplink and downlink
ce Request)
st
value= support HSDPA, UE Category 6
Context Request)
Request
>>"Radio Bearer Description"
value= SF16(uplink)-> PS64
value= HSDPA Channel Information
value= hs-SCCH , Fixed SF 128 , Code No=4,5,6,7
In theory, one cell can configure up to 15 HS-SCCH. But now commercial UE
value= SF256(downlink)
value= HSDPA Serving Cell's Primary SC = 30
lete
Accept
value= SF256(downlink)
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000000010001010100101111 => RNCid=bin2dec(000000000001)=1
DP Context Accept)
n (DCCH)
value= PrimarySC=30, no longer a HSDPA serving cell ( HSDPA Serving Cel
(Old HSDPA's Serving Cell)
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000000010001010100101111 => RNCid=bin2dec(000000000001)=1
mplete (DCCH)
value= PrimarySC=9 is a new HSDPA serving cell ( HSDPA Serving Cell Cha
(New HSDPA's Serving Cell)
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000000000010001000111011100=> RNCid=bin2dec(000000000001)=1
P Context Request)
Request
t Accept
PDP Context Accept)
leted
nection Release)
n Release Complete)
CPICH_RSCPPCPICH PowerUL Interference
UL DPCCH Initial Power
-80
33
-107
-16
-70
33
-107
-26
ower_offset is configured by RNC and delivered to UE in RRC Connection Setup.
1)=1 and Cellid=bin2dec(0001010100101111)=5423
-SCCH. But now commercial UE can only monitor up to 4 HS-SCCH channels simultaneously. So one cell only configure up to 4 HS-SCCH chann
NCid=bin2dec(000000000001)=1 and Cellid=bin2dec(0001010100101111)=5423
erving cell ( HSDPA Serving Cell Change)
NCid=bin2dec(000000000001)=1 and Cellid=bin2dec(0001010100101111)=5423
g cell ( HSDPA Serving Cell Change)
NCid=bin2dec(000000000001)=1 and Cellid=bin2dec(0001000111011100)=4572
onfigure up to 4 HS-SCCH channels
RRC Connection Set up procedure is performed for the UE to set up a signaling
Setup is always initiated by the UE. One UE has a maximum of one RRC connection
Triggering Condition The UE in idle mode initiates the RRC connection set up p
Request the establishment of signaling connection. When the RNC receives an RRC
The UE the Radio Resource Management(RRM) module of the RNC determines whe
request ,based on the specific algorithm. If accepting the request the RMM module
The RRC connection on a Dedicated Channel(DCH) or Common Channel (CCH) base
An RRC connection is setup on the DCH
The PS Session Setup is performed to set up a PS session
Triggering Condition The UE sends activate PDP context request message to R
When the UE initiates a packet call setup. The UE has the state packet mobility ma
To transmit and receive data while moving within a PLMN and starts the PDP conte
And remove a virtual data channel between a terminal connected to UE and GGSN
The PS session release procedure is performed to release services after a sess
Triggering Conditions The UE send Deactivate PDP Context request message t
UE terminates a packet call. Before the deactivation ,the UE has the state active. a
state becomes Packet mobility management connected. The RAB will be released
deactivation maybe initiated by a :UE procedure ,SGSN procedure,GGSN procedure
RRC Connection Release Procedure is performed to release signaling connection
And the UTRAN.
Triggering Condition After the RAB is release the RNC judge whether the RRC con
If judging the RRC connection does not carry other RAB of the UE the RNC initiates as
RRC Connection Release Procedure is performed to release signaling connection
And the UTRAN.
Triggering Condition After the RAB is release the RNC judge whether the RRC con
If judging the RRC connection does not carry other RAB of the UE the RNC initiates as
or the UE to set up a signaling connection to the RNC.RRC Connection
ximum of one RRC connection at a time .
s the RRC connection set up procedure when the NAS of the UE
When the RNC receives an RRC CONNECTION REQUEST message from
le of the RNC determines whether to accept or reject the RRC connection
g the request the RMM module further determines whether to setup
r Common Channel (CCH) based on the specific RRM algorithm .typically
session
context request message to RNC .PDP context activation is performed
s the state packet mobility management connected that enable the user
LMN and starts the PDP context activation procedure used to setup
al connected to UE and GGSN
o release services after a session ends.
DP Context request message to RNC.A PDP Context Deactivation is performed when
,the UE has the state active. after the PDP context deactivation procedure the
ted. The RAB will be released if there area no other PDP context activated.PDP
SN procedure,GGSN procedure.
release signaling connection and all radio bearers between UE
NC judge whether the RRC connection carries any other RAB or the UE.
of the UE the RNC initiates as a RRC connection release procedure.
release signaling connection and all radio bearers between UE
NC judge whether the RRC connection carries any other RAB or the UE.
of the UE the RNC initiates as a RRC connection release procedure.
RRC:RRC Connection Request (RACH)
RRC:RRC Connection Setup (FACH)
RRC:RRC Connection Setup Complete (DCCH)
RRC: Initial Direct Transfer (GMM: Service Request)
RANAP: GMM:Service Request
RRC: Security Mode Command
RRC: Security Mode Complete
RRC: Uplink Direct Transfer (SM: Activate PDP Context Request)
RANAP: SM: Activate PDP Context Request
RRC: Radio Bearer Setup
RRC: Radio Bearer Setup Complete
RANAP: SM: Activate PDP Context Accept
RRC: Downlink Direct Transfer (SM: Activate PDP Context Accept)
RRC: Physical Channel Reconfiguration (DCCH)
RRC:Physical Channel Reconfiguration Complete (DCCH)
RRC: Uplink Direct Transfer (SM: Deactivate PDP Context Request)
RANAP: SM: Deactivate PDP Context Request
RANAP: SM: Deactivate PDP Context Accept
RRC: Downlink Direct Transfer (SM: Deactivate PDP Context Accept)
RRC: Radio Bearer Release
RRC: Radio Bearer Release Completed
RRC: Downlink Direct Transfer (CC: RRC Connection Release)
RRC: Uplink Direct Transfer (CC: RRC Connection Release Complete)
RRC:Measurement Report (e1d)
RRC:Measurement Control
>>"RRC Connection Request Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(5)=5 , hex2dec(2)=2 ,hex2dec(0)=0 --> MCC=520
value=hex2dec(9)=9 , hex2dec(9)=9 --> MNC=99
value=hex2dec(03EA)= 1002
value= OriginatingBackgroundCall (PS MOC)
value=(-24+ (39/2))=-4.5 dB
value=Primary Scrambling Code=60 ( Neighbour's SC)
value=(-24+ (37/2))=-5.5 dB
value= HSPA Release6
value= UE support HSDPA and E-DCH (HSUPA)
>>"RRC Connection Setup Description"
>>"Geographical and UTRAN Entity Identifiers"
value=hex2dec(5)=5 , hex2dec(2)=2 ,hex2dec(0)=0 --> MCC=520
value=hex2dec(9)=9 , hex2dec(9)=9 --> MNC=99
value=hex2dec(03EA)= 1002
value=UE capable to support FDD , not TDD
value=Signaling Radio Bearer Information Setup ,RB-1
value=Radio Bearer Mapping
value=Signaling Radio Bearer Information Setup ,RB-2
value=Signaling Radio Bearer Information Setup ,RB-3
value=Signaling Radio Bearer Information Setup ,RB-4
value=BLER Target= -20 dB
value=MaxAllowedULTxPower=24 dBm
value=(-47*2)= -94 dBm (step of 2 dB)
Default Constant
value= use Closed Loop Power Control Algorithm1
-22
-22
Note :DPCCH_Power_offset is conf
value= use long SC on Uplink
value=Spreading Factor 64 (Uplink)
CH)
value=Spreading Factor 128 (Downlink)
value=Primary Scrambling code=60
value=Spreading Factor 128 (Downlink)
Cell Identity=RNCid(12bits)+Cellid(16bits)
value=0000011001100000010100101001 => RNCid=bin2dec(000001100110)=102 and Cellid=bin2dec(0000
>>"RRC Connection Setup Complete Description"
value= not support GSM (Locked UMTS Mode)
value= Chipering Algorithm A5/3
value= support Compressed Mode (CM) uplink and downlink
value= support HSDPA, UE Category 8
Context Request)
Request
>>"Radio Bearer Description"
value= Uplink e-DPDCH (HSUPA) channel information
value= Downlink HS-PDSCH channel information
lete
value= HSDPA and HSUPA Serving Cell's Primary SC = 68
Accept
DP Context Accept)
n (DCCH)
value= PrimarySC=68, no longer a HSDPA & HSUPA serving cell ( HSPA Ser
value= PrimarySC=60 is a new HSDPA&HSUPA serving cell ( HSPA Serving
mplete (DCCH)
P Context Request)
Request
t Accept
PDP Context Accept)
leted
nection Release)
n Release Complete)
d)
DPCCH_Power_offset
CPICH_RSCPPCPICH PowerUL Interference
UL DPCCH Initial Power
-94
-80
33
-105
-14
-94
-70
33
-105
-24
ote :DPCCH_Power_offset is configured by RNC and delivered to UE in RRC Connection Setup.
0)=102 and Cellid=bin2dec(0000010100101001)=1321
imary SC = 68
HSUPA serving cell ( HSPA Serving Cell Change)
PA serving cell ( HSPA Serving Cell Change)
