McLaren-Honda MP4-30 Quick Users Guide

1|Page

In this guide we will briefly explain a number of key setup parameters which
are distinct to the MP4-30. We hope this introduction will enable members
to familiarize themselves with these features and hit the track quickly, rather
than being overwhelmed by a number of new and unknown variables.

Table of Contents
Aerodynamics 3
Chassis.5
Dampers and Inerters..7
Power Unit..8
Differential.11
Tires.12

2|Page

Aerodynamics
As the McLaren-Honda MP4-30 and other modern grand prix cars are very
much influenced by aerodynamics, we have decided to offer a choice of
three downforce trim levels: low, medium and high. The speed of the track
should determine which trim level to select. Typically, extremely fast tracks
such as Monza, Montreal, or Spa may be best suited to low downforce trim,
slower more technical tracks such as Zandvoort or Laguna Seca might
require high downforce trim to be fastest.
The simplest way to adjust aerodynamic balance is by using the front flap
angle and/or rear wing wicker adjustments. To increase oversteer or
decrease understeer, increase front flap angle and/or decrease rear wing
wicker (vice versa to decrease oversteer or increase understeer). Both
adjustments are only available in the garage or during pit stops with the
MP4-30.
The included aero calculator will allow you to visualize aerodynamic
balance shifts while experimenting with ride heights and front and rear wing
adjustments.
While working with the aerodynamics of the car, keep in mind that drag also
increases as downforce is increased. The downforce to drag ratio in the aero
calculator will provide detail on how much drag will change as the result of
increasing or decreasing downforce.
The MP4-30 features a drag reduction system (DRS). The primary purpose
of the DRS is to facilitate overtaking. Many tracks have pre-defined zones
in which the angle of incidence of the rear wing flap may be set to reduce
overall aerodynamic drag and increase top speed. During practice and
qualifying sessions, every car may always use DRS when in these pre-set
zones. However, during races, only cars that are within 1 second of the car
in front when crossing a specified DRS detection point may use the DRS.
Note that DRS use is completely disabled during the first two laps of every
race. The steering wheel display and in-car controls are used to determine
DRS availability and engagement. When the driver crosses a detection
point, a single blue light will illuminate on the left-hand side of the steering
wheel display unit if DRS will be available in the next zone. When the
driver subsequently crosses the start of the next DRS zone, a second blue
light illuminates to indicate that DRS is available. The driver must then
3|Page

manually use the control DRS (available to be mapped in the Options menu)
to engage the DRS. When the DRS is engaged, two more blue lights
illuminate. DRS may be disengaged manually by toggling the DRS control
OR by lifting off of the throttle OR by applying the brakes.

4|Page

Chassis
Although the MP4-30 suspension layout is quite similar to that of the FW31,
in actuality it is more analogous to those found on most other single-seat
racecars.
Both the front and rear suspensions include conventional corner springs
(torsion bars as opposed to coil springs) and, unlike the FW31, anti-roll bars
at both ends. Also included are third springs front and back. We refer to
these springs as heave springs. The heave springs add additional wheel rate
stiffness in vertical heave, or bounce motion, only. Their primary function is
to help control the chassis platform in order to keep consistent aerodynamic
performance. High heave rate settings will result in less ride height change
while the car rides over bumps and while downforce increases as vehicle
speed rises versus softer heave rate settings.
The key in adjusting these components is finding the appropriate amount of
stiffness to help aid the aerodynamics while maintaining an adequate amount
of front mechanical grip. At faster tracks the best compromise might be to
use stiffer heave rate and give up some mechanical grip in exchange for
better aerodynamics control, whereas at much slower tracks where raw tire
grip would take precedence, perhaps less heave rate would be required. The
correct way to set both the front and rear heave spring is to choose the rates
and adjust their perch offsets until the springs are at least slightly preloaded
while the car has no fuel. This will ensure that, as fuel weight burns off, the
heave springs will always be carrying vehicle load rather than 'floating' off
of their perches, thus forcing the corner springs to do extra work to hold up
either end of the car.
Ballast adjustability as also available in the MP4-30. Ballast placement, and
correspondingly calculated nose weight percentage, allows members to shift
weight forwards and rearwards to affect static front and rear corner weights
and consequently mechanical balance in corners. More forward weight
distribution will reduce oversteer/ increase understeer during cornering
events. However, it may reduce the amount of acceleration traction available
powering out of a corner. More rearward percentage will produce just the
opposite effects.
In keeping with our previous high level racing cars, we have made available
multiple brake pressure settings to enable drivers to reduce or increase
5|Page

braking force to their preference. These settings are scaled to downforce

trim level, so the recommended setting aligns with which downforce trim
has been selected.
Finally, in addition to brake pressure the MP4-30 also has an innovative way
of changing front to rear braking bias percentage with pedal travel.
Typically, at higher speeds more front brake bias would be advantageous to
help decelerate the vehicle due to aerodynamic down load; however, as
speeds decrease the optimal brake bias may need to be more rearward. Base,
peak and begin bias ramping parameters allow the driver to set the
minimum and maximum front brake bias, and ramping determines where the
minimum value will start to ramp up towards the peak number. Play around
with these settings at different race tracks and see which settings work best
for you. New to the McLaren is the ability to not only alter the base brake
bias, via a typical cockpit adjuster, but also the peak brake bias individually
via a control dial (BAL) in-car on the steering wheel. The idea is to allow
the driver to alter both peak and base brake bias settings individually ontrack to suit track, downforce level, and driving style.

6|Page

Dampers and Inerters

Not only does the McLaren MP4-30 have typical corner dampers, it also has
dampers assigned to each heave spring. These heave dampers, similar to the
additional third springs, only work with vertical heave, or bounce, motion.
Each corner damper has low speed and high speed adjustments in both
compression and rebound in order to optimize the ride and handling
performance of the car. However, the heave dampers utilize low speed
damping and something we call high speed slope adjustments. The high
speed slope adjustments have a very broad range of damping adjustability in
order to allow for large force tuning at high damper shaft speeds. The
allowable range can exhibit fairly linear force behavior, which keeps high
levels of damper force, as well as the ability to blow-off damper force,
resulting in very low levels of damping; much more damping adjustment
than is typical compared to our low speed or high speed damping
adjustments. A bumpy track or one with large curbs might require a different
set of parameters than a smooth track or one where curbs dont come into
play.
Other innovative tuning elements featured include front and rear inerters.
These inerters literally add inertial mass to the un-sprung suspension without
actually adding weight to the wheels, thereby avoiding the pitfalls associated
with extra weight. More inertia will reduce the ride frequency or response
time of the suspension just like a heavier wheel would, and may be
beneficial over different types of track surfaces. In some instances a lot of
inerter mass will be beneficial and at other times no inertial mass will be
preferable.

7|Page

Power Unit
The Honda power unit in the MP4-30 consists primarily of a turbocharged
internal combustion engine, two motor generator units (MGUs), and an
electrical energy store. The MGUs and electrical energy store are part of an
energy recovery system (ERS), the purpose of which is to capture and redeploy energy that would otherwise be dissipated as heat. The ERS system
increases the overall efficiency of the power unit, allowing the MP4-30 to
consume less fuel than an equivalent car thats not equipped with an ERS.
One of the MGUs is directly linked to the engines crankshaft. This MGU
acts as a generator when the car is braking, recovering Kinetic energy that
would otherwise be dissipated as heat from the brakes. Its called the MGUK (for kinetic). The MGU-K also deploys electrical energy to propel the
car; in this mode, the MGU-K acts as a motor.
The other MGU is directly linked to the shaft of the engines turbo. The
turbo harvests Heat from the engines exhaust via a turbine, and deploys that
power to increase the amount of air supplied to the engine intake via a
compressor. The MGU thats attached to the turbo shaft on the MP4-30 is
called an MGU-H (for heat). The turbine on the MP4-30 is very efficient
and, when the engine is operating at moderate-to-high revs, produces more
power than the compressor needs to supply the engine with sufficient intake
air. This allows the MGU-H to act as a generator, harvesting the excess
power from the turbine, which may either be deployed through the MGU-K
to propel the car or directed to the electrical energy store (a battery pack we
refer to as the ERS battery). When the driver is off-throttle, the turbo will
slow down, and will take time to speed back up when the driver applies the
throttle at corner exit. This causes a delay in the supply of intake air and,
consequently, engine power, thats known as turbo lag. On the MP4-30, the
MGU-H may act as a motor when the driver is off-throttle, maintaining
turbo speed to eliminate turbo lag.
The governing body of Formula 1, the Federation Internationale de
LAutomobile (FIA), mandates limits on power and energy flow among the
three primary ERS components. The FIA also sets strict limits on the total
fuel with which a car may start races (mid-race re-fueling is not permitted),
and the maximum fuel flow to the engine as a function of engine speed.
The MP4-30 has advanced control software designed to manage the overall
operation of the ERS in order to ensure maximum performance and
8|Page

compliance with the FIA regulations. A number of adjustment parameters

are available to the driver to tune system performance to suit particular
circumstances. All of these settings are available in the Garage. Most are
also available in-car via the F8 black box.
MGU-K re-gen gain sets how aggressively the MGU-K applies regenerative
braking, which plateaus at an FIA-mandated limit of 120 kW. This
parameter may be mapped to control keys using the Engine Braking settings
in the Options menu. Lower regeneration can make braking more stable.
Higher regeneration harvests more energy. The driver should target the
greatest regeneration level at which braking is stable.
MGU-K deployment generally determines how much power is available to
propel the car. If MGU-K deployment is greater than MGU-H harvesting,
power will be drawn from the ERS battery, and the ERS battery charge level
will decrease. The driver must manage power draw from the ERS battery by
setting the MGU-K deployment level. MGU-K deploy mode toggles
between two different approaches to setting MGU-K deployment level:
fixed and adaptive. This parameter may be mapped to control keys using the
MGU-K Deploy Mode settings in the Options menu. In fixed mode, the
system will deploy the MGU-K at a power level set by MGU-K deploy fixed.
This parameter may be mapped to control keys using the MGU-K Fixed
Deploy Mode settings in the Options menu. In adaptive mode, the system
will deploy the MGU-K at an appropriate level to hit an ERS battery charge
percentage set by MGU-K deploy adaptive. This parameter may be mapped
to control keys using the MGU-K Adaptive Deploy settings in the Options
menu. If MGU-K deployment suddenly drops from near maximum power to
no power, the rain light flashes to warn following drivers that the cars
acceleration will decrease significantly.
The driver must manage fuel use carefully during races. A fuel display
appears on the steering wheel every time the driver crosses start-finish
during the race. Fuel used on the previous lap, a target fuel used per lap, and
the projected amount of fuel with which the driver will finish the race are
displayed. A driver may save fuel by adopting different driving techniques
(early lifts at the ends of straights and smooth throttle application are
generally considered to be the most effective ways to do this) or by changing
engine mode. Fuel consumption sets the engine mode. This parameter may
be mapped to control keys using the Fuel Mixture settings in the Options
menu.
9|Page

An overtake function is available to increase propulsive power for short

periods. Overtake is only enabled when the driver activates the Push To
Pass control key, which must be held down for the entire duration of
engagement. Be aware that overtake use depletes the ERS battery, so must
be carefully managed during races.
Finally, throttle pedal shaping allows the driver to select the type of engine
performance as he/she rolls into the throttle pedal coming off a corner.
Setting 1 maps the throttle-to-torque relationship just like a typical engine
that uses a butterfly throttle plate. Setting 4 uses a linear throttle-to-torque
output relationship. The two settings in between blend the butterfly model
and the direct linear torque model together. This setting is completely
dependent on driver preference. At race tracks with low grip and slow
speeds, where exit performance is critical for fast lap times, you may want to
use the more conventional butterfly shape throttle curve in order to control
the power application. Conversely, drivers might want the brute force
torque from the linear torque pedal for faster tracks, where feathering the
throttle off the corner is less important. Note that FIA rules prohibit
changing throttle mapping while the car is on track, and so this function may
only be set while the car is in the garage.

10 | P a g e

Differential
The iRacing MP4-30 also gives iRacing members the ability to design
differential settings. Members will have the ability to choose differential
locking settings for different segments of the corner. As with current grand
prix race cars, this area has a major influence on the performance of the
racecar. More entry preload, entry and middle differential locking will
increase understeer or decrease oversteer on entry and through the middle of
corners. On exit more locking will increase oversteer or reduce understeer.
For entry to middle sections of a corner, this setting mainly controls vehicle
balance: however on exit not only does it affect balance, it also alters the
amount of acceleration thrust generated by both wheels. A compromise will
need to be found which will allow the most amount of locking to power
straight out of a corner without overwhelming the rear tires and generating
too much oversteer during corner exit. The driver will also have the ability
to make micro adjustments to the differential settings in the garage or via
dials in-car (PL and ENT) while driving, which will slightly increase or
decrease understeer and oversteer performance of the diff. In-car controls
may be mapped to external keys/buttons with the Diff Preload and Diff
Entry in-car adjustments in the Options menu.

11 | P a g e

Tires
A quick note about the optimum tire settings for the MP4-30 on road
circuits: Peak lateral grip should be in 17-22 psi hot range for both front and
rear tires. Optimal longitudinal drive and braking grip will likely be in the
lower end of the peak lateral range or possibly a little less. Peak grip will be
maintained in and around 210-230 F in average temperature, with some
temperature spread from inside to outside of the tire being reasonable. Best
camber angles to use are anywhere from -2.5 to -3.5 degrees in the front and
-0.5 to -1.5 degrees in the rear. For directional stability it makes sense to run
with some amount of toe-out (negative toe-in) at the front of the car and toein (positive toe-in) at the back of the car.

12 | P a g e