Scribd
Upload
442 views

Specification For Control Valve

The document provides specifications for control valves and accessories. It details requirements for valve sizing, construction, direction of flow, marking, painting, position indicators, noise levels, positioners and required accessories.

Uploaded by

amilasri
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
442 views

Specification For Control Valve

The document provides specifications for control valves and accessories. It details requirements for valve sizing, construction, direction of flow, marking, painting, position indicators, noise levels, positioners and required accessories.

Uploaded by

amilasri
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

GENERAL SPECIFICATIONS OF CONTROL VALVES

& ACCESSORIES

1.0

CONTROL VALVE SIZING

Sizing of the Control valve should be carried out such as to prevent flashing, cavitation & in
conformity with the noise requirements mentioned in clause 7.0, based on the data &
operating conditions attached. Results of the sizing calculations shall be forwarded with the
quotation.
No quotation will be evaluated without the results of the sizing calculation. Generally valve
shall have twice the Cv required for the normal design flow at specified condition. The
Normal Flow Cv does not include any factors relating to the geometry of the valve on its
installation. The valve size and approximate valve Cv should include allowances for such
factors.

2.0

VALVE CONSTRUCTION

2.1

The Control Valve body should be manufactured of castings or forgings to the ASTM
A216 Grade WCB material specification. The quality of and repair of body casting
must

follow the requirements of the referenced ASTM material specification. Wall

thickness shall meet or exceed minimum requirements of applicable codes.

2.2

The valves shall have suitable guiding to prevent excessive shaft deflection due to
maximum differential pressure or actuator thrust.

2.3

Bonnets and bottom flanges shall be of integral type or bolted type construction with
fully retained gasketting.

2.4

Bonnet and bottom flanges shall be of the same generic material as the body, and made
of castings, forgings or plate where applicable.

H:\From D\Amila\specification\Specification for Control Valve.doc

3.0

DIRECTION OF FLOW

The vendor shall determine the direction of flow, which is more desired for the operating
conditions & which will comply the noise requirements given in clause 7.0.
The direction of flow should be clearly marked on the valve body, embossed during casting
or using Stainless Steel Tag displaying the Inlet & outlet on the flange faces.

4.0

VALVE MARKING

The Control Valve should have Stainless Steel nameplate permanently fastened to the
superstructure which shall be visible when the valve is in service. This name plate shall
include the following information.

5.0

4.1.

Manufacturers' name or trademark/Valve Tag number

4.2.

Valve Model and serial number.

4.3.

Maximum valve body pressure rating.

4.4

Valve body material and nominal pipe size.

4.5

Trim material, size, characteristics and travel.

4.6

Valve action and operating signal characteristics.

CONTROL VALVE PAINTING (COLOUR)

Refer to the specification sheets attached.

6.0

CONTROL VALVE POSITION INDICATOR

A Travel Indicator with OPEN, CLOSED & INTERMEDIATE POSITIONS clearly marked
on a Stainless Steel Tag plate to be attached to indicate the valve position.

7.0

NOISE REQUIREMENTS

The noise generated by the Control Valve measured at a distance of 1 meter shall be less than
90 dB.
H:\From D\Amila\specification\Specification for Control Valve.doc

8.0

CONTROL VALVE POSITIONER

8.1

Control valve positioners shall be of Electro-pneumatic type with the feed-back link.

8.2

The Valve Positioner shall be either Yoke mounted motion balance or integral force
balance type and they shall not be affected mechanically or functionally by any
vibration encountered when so mounted.

8.3

The Valve Positioners shall be easily converted from direct to reverse acting.

8.4

The Valve Positioner shall be an Intrinsically Safe apparatus suitable for installation in
Class I, Groups D, Division 1 area as defined in the National Electric Code of practice
(NEC). The equipment & materials of construction shall be listed, certified & approved
by FM, UL, BASEEFA, CSA or any other internationally recognized, independent
testing authority.

8.5

The valve positioner should be dynamically balanced and have a linearity of 1% of full
scale.

If necessary temperature compensated coils shall be provided to maintain the

linearity.

8.6

Input impedance characteristics shall be suitable for operation with Micro-processor


based, Single Loop Indicating Controller.

8.7

Input to the Electro Pneumatic

4 - 20 mA DC, 2-wire

valve positioner

current signal

The Valve Positioner shall have 1/4" NPT (F) pneumatic connections and 1/2" NPT (F)
OR 20 mm (F) electrical connection.

8.8

The Valve Positioner shall be equipped with an Air filter/ Regulator & a set of gauges
for supply and output signals.

8.9

Utilities available : Instrument air 60 psig. (Max)

H:\From D\Amila\specification\Specification for Control Valve.doc

8.10

Weatherproof Class

: IP 55

8.11 Ambient Temperature : 20 oC - 40 oC

8.12

9.0

Relative Humidity

: 65% - 95%

ACCESSORIES

The control valve shall be equipped with accessories mentioned in the table attached.
Mounting of accessories on the control valve and interconnecting tubing shall be
done by the supplier.

Abbreviated Accessories

9.1

EPP : Electro-pneumatic control valve positioner with gauges for supply and output signals
as specified under clause 8.0.

9.2

AFR : Air filter, Regulator with gauge


SOL : Explosion proof 110 V DC operated
Solenoid valve certified to EEx d11CT6
For Hazardous area installation.

9.3

CF

9.4

HW : Hand Wheel

10.0

: Cooling fins

TECHNICAL LITERATURE

Catalogues containing specifications shall be furnished along with the quotation and operation
and maintenance manuals containing principle of operation, trouble shooting servicing and
calibration procedures of the Valve Positioner & spare part lists with part numbers of the
Control Valve and the Positioner to be supplied along with the equipment on delivery.
All documentation shall be in English Language.

H:\From D\Amila\specification\Specification for Control Valve.doc

11.0

TEST CERTIFICATES & OTHER DOCUMENTS

11.1

Certified construction drawings, technical specification sheet & Valve sizing calculation
for the Control Valve shall be provided with the quotation.

11.2

Material test certificates including chemical and tensile properties according to


EN 10204, 3.1B shall be furnished with control valves.

11.3

Following tests shall be carried out for the valve according to ANSI, IEC standards
mentioned below and test certificates shall be furnished with the valves.

11.3.1 Hydrostatic shell test ANSI B 16.34, IEC 534-4

11.3.2 Leak test of Body

ANSI B 16.34, IEC 534-4

11.3.3 Seat leakage test

ANSI FCI 70-2, IEC 534-4

11.3.4 Functional test

IEC 534-4

H:\From D\Amila\specification\Specification for Control Valve.doc

You might also like