Scribd
Upload
288 views

Analysis of Frame Structure

The document discusses the analysis of plane frame structures. It introduces plane frames as a combination of plane trusses and two-dimensional beams. Plane frames have three degrees of freedom at each node: axial deformation, vertical deformation, and rotation. The member stiffness matrix is derived as the combination of truss and beam stiffness matrices. Generalized stiffness matrices are obtained by transforming local member matrices to the global coordinate system. An example plane frame is analyzed by establishing nodal coordinates, member properties, applying loads, formulating the global stiffness matrix, determining displacements, and calculating member end actions.

Uploaded by

Rashed
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
288 views

Analysis of Frame Structure

The document discusses the analysis of plane frame structures. It introduces plane frames as a combination of plane trusses and two-dimensional beams. Plane frames have three degrees of freedom at each node: axial deformation, vertical deformation, and rotation. The member stiffness matrix is derived as the combination of truss and beam stiffness matrices. Generalized stiffness matrices are obtained by transforming local member matrices to the global coordinate system. An example plane frame is analyzed by establishing nodal coordinates, member properties, applying loads, formulating the global stiffness matrix, determining displacements, and calculating member end actions.

Uploaded by

Rashed
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Module 4: Analysis of Frame Structures

Lecture 5: Plane Frame Analysis

31

4.5.1 Introduction
The plane frame is a combination of plane truss and two dimensional beam. All the members
lie in the same plane and are interconnected by rigid joints in case of plane frame. The
internal stress resultants at a cross-section of a plane frame member consist of axial force,
bending moment and shear force.
4.5.2 Member Stiffness Matrix
In case of plane frame, the degrees of freedom at each node will be (i) axial deformation, (ii)
vertical deformation and (iii) rotation. Thus the frame members have three degrees of
freedom at each node as shown in Fig. 4.5.1 below.

Fig. 4.5.1 Plane frame element


Therefore, the stiffness matrix of the frame in its local coordinate system will be the
combination of 2-d truss and 2-d beam matrices:
u1

v1

u2

0
0

v2

(4.5.1)

4.5.3 Generalized Stiffness Matrix


In plane frame the members are oriented in different directions and hence it is necessary to
transform stiffness matrix of individual members from local to global co-ordinate system

32
before formulating the global stiffness matrix by assembly. The generalized stiffness matrix
of a frame member can be obtained by transferring the matrix of local coordinate system into
its global coordinate system. The transformation matrix can be expressed as:

cos
sin
0
[T]=
0
0
0

sin
cos
0
0
0
0

0
0
1
0
0
0

0
0
0
cos
sin
0

0
0
0
sin
cos
0

0
0
0
0
0
1

(4.5.2)

Now, the generalized stiffness matrix of the member can be obtained from the relation of
. Thus considering
cos and
sin the stiffness matrix in global
coordinate system can be written as follows:
AE
AE
0
0
0
0
L
L
12EI 6EI
12EI
6EI
0
0

0 0 0 0
L
L
L
L
6EI
6EI
4EI
2EI
0 0 0 0
0
0
0 0 1 0 0 0
L
L
L
L
K
EI

AE
AE
0 0 0
0
0
0
0
0
0 0 0 0
L
L
12EI
6EI
12EI
6EI
0 0 0 0 0 1
0
0
L
L
L
L
6EI
6EI
2EI
4EI
0
0
L
L
L
L
0 0 0 0
0 0 0 0
0 0 1 0 0 0

0 0 0 0
0 0 0
0
0 0 0 0 0 1

EA

L
EA

12EI

L
12EI

L
6EI

L
EA
12EI

L
L
EA
12EI

L
L
6EI

EA
12EI

L
L
EA
12EI

L
L
6EI

L
EA
12EI

L
L
EA
12EI

L
L
6EI

6EI

L
6EI

L
4EI
L
6EI

L
6EI

L
2EI
L

EA
12EI

L
L
EA
12EI

L
L
6EI

L
EA
12EI

L
L
EA
12EI

L
L
6EI

EA
12EI

L
L
EA
12EI

L
L
6EI

L
EA
12EI

L
L
EA
12EI

L
L
6EI

6EI

L
6EI

L
2EI
L
6EI

L
6EI

L
4EI
L

33
(4.5.3)

4.5.4 Worked Out Example


Analyse the plane frame shown below. Assume the modulus of elasticity of the horizontal
member is 1.5 times that of the vertical member and length of the vertical member is 1.5
times that of horizontal member. Find the bending moment and reactions at support
assuming the length, cross section area and modulus of elasticity of vertical member as
3.0 m, 0.4 x 0.4 m2 and 2 x 1011 N/mm2, respectively.

Fig. 4.5.2 Plane frame


Solution
Step 1: Numbering of Nodes and Members
The numbering of members and joints of the plane frame are as shown below:

Fig. 4.5.3 Numbering of Nodes and Members

The members AB and BC are designated as (1) and (2). The points A, B and C are designated
by nodes 1, 2 and 3. The member information for the frame is shown in tabulated form as
shown in Table 1(a). The coordinate of node 1 is assumed as (0,0). The coordinate and
restraint joint information are shown in Table 1(b). The integer 1 in the restraint list indicates

34
the restraint exists and 0 indicates the restraint at that particular direction does not exist.
Thus, in node no. 2, the integer 0 all the restraint type indicates that the joint is in free all the
three directions.
Table 4.5.1 Member Information for Beam
Starting node
Ending node
1
2
2
3

Member number
1
2

Node no.
X
0
0
L

1
2
3

Rigidity modulus
EI
1.5EI

Table 4.5.2 Nodal Information for Beam


Coordinates
Restraint list
Y
Axial
Vertical
0
1
1
1.5L
0
0
1.5L
1
1

Rotation
1
0
1

Step 2: Formation of member stiffness matrix:


The individual member stiffness matrices can be found out directly from eqn. shown above.
Thus the stiffness matrices of each member in global coordinate system are given below
based on their individual member properties and orientations. Thus the stiffness matrix of
member (1) is:
1

0
0

Similarly, the stiffness matrix of member (2) is :


4

2
3
4

5
6

35
.

Step 3 : Formulation of global stiffness matrix:


The global stiffness matrix is obtained by assembling by assembling the local stiffness matrix
of member (1) and (2) as follows:
1

0
.

0
0

[K] =

0
0

Step 4: Boundary conditions:


The boundary conditions according to the support of the frame can be expressed in terms of
the displacement vector. The displacement vector will be as follows:
0
0
0

Here,
and
,
and rotation at point B.
Step 5: Load vector:

0
0
0
indicate the displacement in X-direction, displacement in Y-direction

36
The distributed load on member (2) can be replaced by its equivalent joint load as shown in
the figure below.

Fig. 4.5.4 Equivalent Joint Loads

Thus, the equivalent joint load vector can be written as


0
0
0
0
2
12
0
2
12
Step 6: Determination of unknown displacements:
The unknown displacements can be obtained from the relationship of {F} = [K]{d} or
{d} =[k]-1 {F}. Now eliminating the rows and columns in the stiffness matrix and force
matrix, corresponding to zero elements in displacement matrix, the reduced matrix will be as
follows.
32
9

1.5
0

8
3
9

0
2
3

8
3
Thus, the unknown displacements will be:

18
9

8
3

0

6

2
12

0.04327
1.7127
5.4978
Step 7: Determination of member end actions:
The member end actions can be obtained from the corresponding member stiffness and the
nodal displacements. The member end actions for each member are derived as shown below.
1
10

37

Member (1)
In case of member (1), the member forces will be:
56.17
0
126.4
10
56.17
0
126.4

0
7110
0
0
7110
0

126.4
0
379.2
379.2
0
189.6

56.17
0
126.4
56.17
0
126.4

0
7110
0
0
7110
0

126.4
0
189.6
126.4
0
379.2

0
0
0
4.327 10
1.7127 10
5.4978 10

0.0697
1.2177
0.10479
0.06925
1.21661
0.20793

It is to be noted that {Fm} are the end actions due to joint loads. Hence it must be added to the
corresponding end actions in the restrained structure in order to obtain the end actions due to
the loads. Therefore, {Fm}actual are the true member end actions due to actual loading system
can be expressed as
= {Fm} + {Ffm}
Where, {Ffm} are the end actions in the restrained structure. Since there is no load acting on
member (1), the actual end actions will be:

{Fm}actual =

0.0697
1.2177
0.10479
0.06925
1.21661
0.20793

0
0
0
0
0
0

0.0697
1.2177
0.10479
0.06925
1.21661
0.20793

Member (2)
In similar way, the member forces in member (2) will be {Fm}(2) = [K](2){d}(2)

38

10

16
0
0
16
0
0

0
0.284
0.426
0
0.284
0.426

0
0.426
0.853
0
0.426
0.426

16
0
0
16
0
0

0
0.284
0.426
0
0.284
0.426

0.069232
0.28325
0.54215
=
0.06923
0.283245
0.3076
The actual member forces in the member (2) will be:

0.069232
0.28325
0.54215
{Fm}actual =
0.06923
0.283245
0.3076

0
1.5
0.75
0
1.5
0.75

0.0692
1.2167
0.2078
0.0692
1.7832
1.0576

0
0.426
0.426
0
0.426
0.853

4.327 10
1.7127 10
5.4978 10
0
0
0

You might also like