Product Data Sheet
Edition 0607 / 1
Sikagard-61 TZ
Sikagard-61 TZ
Construction
Epoxy splash zone coating
Product
Description
Sikagard-61 TZ is a high performance solvent free, two part epoxy coating
designed to provide corrosion resistance and abrasion protection in extreme
service applications. This specially designed epoxy system is capable of curing
underwater and form a tough protective barrier.
Uses
Sikagard-61 TZ is designed to provide corrosion protection for metal and
concrete structures in offshore marine and petrochemical services, sheet piles,
underground and submarine pipes, waste water tanks, jetty piles, underground
tanks and other structural steel that requires protection against corrosion in
aggressive environment.
It is most suitable for use in the rehabilitation of corroded steel and concrete
structures in tidal zones.
Advantages
Durable tough and impermeable layer with excellent resistance against salt
and water
High build can be applied up to 250 microns in one coat
Chemical resistant good resistance against wide range of chemicals
Underwater curing capable of curing under water
Adhesion excellent adhesion to damp surfaces
Cures at low temperatures
Product Data
Form
Appearance / Colour
Grey, Black
Finish
Gloss
Packaging
5 kg sets
Storage
Storage Condition /
Shelf Life
2 years from the date of production if stored properly in original, unopened and
undamaged sealed packaging in dry conditions.
Technical Data
Solids Content by
Volume
98% 2%
Sikagarc-61 TZ
1/3
Resistance
Chemical Resistance
Guide
Exposure
Immersion
Splash & Spillage
Fumes
Acids
Very Good
Excellent
Excellent
Alkali
Very Good
Excellent
Excellent
Solvents
Very Good
Excellent
Excellent
Salt Water
Excellent
Excellent
Excellent
Water
Excellent
Excellent
Excellent
System Information
Application Details
Consumption
Surface Preparation
Recommended thickness is 250 microns DFT (500 microns for severe
environment)
2
Theoretical coverage is 2.3 m per kg at 250 microns DFT
Recommended 2 coats
Remove oil or grease from surface to be coated. Surface to be free from loose
and friable materials.
Steel
For maximum protection, sand blast to remove surface contaminants and create
surface profile about 50 to 75 microns.
Concrete
Wet blasting or high pressure water jet blasting is recommended to remove
surface contaminants before application of coatings.
Application Instructions
Mixing
Mix part A thoroughly then mix in part B and mix till homogeneous. Do not break
sets.
Thinning is not recommended.
Application Method /
Tools
Sikagard-61 TZ can be applied by brush, roller or spray.
Pot Life
25 minutes (varies with temperature)
Cleaning of Tools
Clean all tools and application equipment with Thinner-C immediately after use.
Hardened and/or cured material can only be mechanically removed.
Curing Details
Curing
Touch dry
Topcoat
Full Cure
2 hours (at + 20C)
12 hours (at +20C)
7 days (at 20C)
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Health and Safety
Information
For information and advice on the safe handling, storage and disposal of chemical
products, users should refer to the most recent Material Safety Data Sheet
(available upon request) containing physical, ecological, toxicological and other
safety-related data.
Sikagarc-61 TZ
2/3
The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sikas recommendations. In
practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose,
nor any liability arising out of any legal relationship whatsoever, can be inferred
either from this information, or from any written recommendations, or from any
other advice offered. The user of the product must test the products suitability for
the intended application and purpose. Sika reserves the right to change the
properties of its products. The proprietary rights of third parties must be observed.
All orders are accepted subject to our current terms of sale and delivery. Users
must always refer to the most recent issue of the local Product Data Sheet for the
product concerned, copies of which will be supplied on request.
Construction
Legal Note
Sika Kimia Sdn Bhd
Lot 689 Nilai Industrial Estate
71800 Nilai, Negeri Sembilan DK
MALAYSIA
Phone: +6 06 799 1762
Fax:
+6 06 799 1980
e-mail:
[email protected]www.sika.com.my
Sikagarc-61 TZ
3/3
