Scribd
Upload
2K views

Standard Proctor Compaction Test

This document describes the procedure for conducting a standard Proctor compaction test according to ASTM D698. The test involves compacting layers of moist soil in a standardized mold using a hammer, then measuring the dry unit weight and moisture content at different compaction levels. The dry unit weight is plotted against moisture content to determine the optimal moisture content for maximum compaction.

Uploaded by

Sami Sami
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
2K views

Standard Proctor Compaction Test

This document describes the procedure for conducting a standard Proctor compaction test according to ASTM D698. The test involves compacting layers of moist soil in a standardized mold using a hammer, then measuring the dry unit weight and moisture content at different compaction levels. The dry unit weight is plotted against moisture content to determine the optimal moisture content for maximum compaction.

Uploaded by

Sami Sami
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

ME 420L/ME 506L: Soil Mechanics Laboratory

Lab No. 6: Standard Proctor Compaction Test


ASTM D698

Introduction: For the construction of highways, airports, and other structures, it is often
necessary to compact soil to improve its strength. This test is referred to as the standard proctor
compaction test and is based on the compaction of the soil fraction passing U.S. No. 4 sieve.

Procedure
1. Obtain about 10 lb (4.5 kg mass) of air-dry soil on which the compaction test is to be
conducted. Break all the soil lumps.
2. Sieve the soil on a U.S. No. 4 sieve. Collect all of the minus 4 material in a large pan.
This should be about 6 lb (2.7 kg mass) or more.
3. Add enough water to the minus 4 material and mix it in thoroughly to bring the moisture
content up to about 5%.
4. Determine the weight of the Proctor mold + base plate (not the extension), W1 (lb).
(Figure 1)

(a)
(b)
Figure 1: Standard compaction mold (a) isometric view (b) top view
5. Now attach the extension to the top of the mold.
6. Pour the moist soil into the mold in three equal layers. Each layer should be compacted
uniformly by the standard Proctor hammer (Figure 3) 25 times before the next layer of
loose soil is poured into the mold.

Figure 3: Standard Proctor hammer


Note: This lab instruction has been prepared by using the following Soil Mechanics Laboratory Manual:
Das, B. M. (2009). Soil Mechanics Laboratory Manual. 7th Edition, Oxford University Press Inc, New York.

ME 420L/ME 506L: Soil Mechanics Laboratory


Lab No. 6: Standard Proctor Compaction Test
ASTM D698

7. Remove the top attachment from the mold. Be careful not to break off any of the
compacted soil inside the mold while removing the top attachment.
8. Using a straightedge, trim the excess soil above the mold. Now the top of the compacted
soil will be even with the top of the mold.
9. Determine the weight of mold + base plate + compacted moist soil in mold, W2 (lb).
10. Remove the base plate from the mold. Using a hydraulic jack (sample ejector), extrude
the compacted soil cylinder from the mold. (Figure 4)

Figure 4: Sample ejector


11. Take a moisture can and determine its mass, M3 (g).
12. From the moist soil extruded in Step 10, collect a moisture sample in the moisture can
(step 11) and determine the mass of the can + moist soil, M4 (g).
13. Place the moisture can with the moist soil in the over to dry to a constant weight.
14. Break the rest of the compacted soil (to No. 4 size) by hand and mix it with the leftover
moist soil in the pan. Add more water and mix it to raise the moisture content by about
2%.
15. Repeat Steps 6 through 12. In this process, the weight of the mold + base plate + moist
soil (W2) will first increase with the increase in moisture content and then decrease.
Continue the test until at least two successive down readings are obtained.
16. The next day, determine the mass of the moisture cans + soil samples, M5 (g) (from Step
13).

Note: This lab instruction has been prepared by using the following Soil Mechanics Laboratory Manual:
Das, B. M. (2009). Soil Mechanics Laboratory Manual. 7th Edition, Oxford University Press Inc, New York.

ME 420L/ME 506L: Soil Mechanics Laboratory


Lab No. 6: Standard Proctor Compaction Test
ASTM D698

Description of Soil:
Location:
Volume of Mold:

1/30 ft3

Weight of Hammer:

Number of Blows/Layer: 25

5.5 lb

Number of Layers: 3

Specific Gravity:
Tested by:

Date:
Test

1. Weight of mold and base plate,


W1 (lb)
2. Weight of mold and base plate +
moist soil, W2 (lb)
3. Weight of moist soil, W2 - W1
(lb)
4. Moist unit weight,
5. Moisture can number
6. Mass of moisture can, M3 (g)
7. Mass of can + moist soil, M4 (g)
8. Mass of can + dry soil, M5 (g)
9. Moisture content, w (%)
10. Dry unit weight of compaction

=
1 +

Plot d and ZAV versus w(%). ( =

Note: This lab instruction has been prepared by using the following Soil Mechanics Laboratory Manual:
Das, B. M. (2009). Soil Mechanics Laboratory Manual. 7th Edition, Oxford University Press Inc, New York.

You might also like