Lab 3.5.

2: Subnetting Scenario 1
Topology Diagram

192.168.9.192/27

192.168.9.96/27

192.168.9.32/27

192.168.9.128/27

192.168.9.160/27

192.168.9.64/27

192.168.9.0/27

Addressing Table
Device

Interface

IP Address

Subnet Mask

Default Gateway

Fa0/1

192.168.9.193

255.255.255.224

N/A

S0/0/0

192.168.9.129

255.255.255.224

N/A

S0/0/1

192.168.9.161

255.255.255.224

N/A

Fa0/0

192.168.9.65

255.255.255.224

N/A

Fa0/1

192.168.9.97

255.255.255.224

N/A

S0/0/0

192.168.9.158

255.255.255.224

N/A

Fa0/0

192.168.9.33

255.255.255.224

N/A

Fa0/1

192.168.9.1

255.255.255.224

N/A

S0/0/1

192.168.9.190

255.255.255.224

N/A

PC1

NIC

192.168.9.222

255.255.255.224

192.168.9.193

PC2

NIC

192.168.9.126

255.255.255.224

192.168.9.97

PC3

NIC

192.168.9.94

255.255.255.224

192.168.9.65

PC4

NIC

192.168.9.62

255.255.255.224

192.168.9.33

PC5

NIC

192.168.9.30

255.255.255.224

192.168.9.1

HQ

BRANCH
1

BRANCH
2

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 1 of 4

CCNA Exploration
Routing Protocols and Concepts:
Introduction to Dynamic Routing Protocols

Activity 3.5.2: Subnetting Scenario 1

Learning Objectives
Upon completion of this lab, you will be able to:

Determine the number of subnets needed.

Determine the number of hosts needed.

Design an appropriate addressing scheme.

Assign addresses and subnet mask pairs to device interfaces and hosts.

Examine the use of the available network address space.

Determine how static routing could be applied to the network.

Scenario
In this lab, you have been given the network address 192.168.9.0/24 to subnet and provide the IP
addressing for the network shown in the Topology Diagram. The network has the following addressing
requirements:

The BRANCH1 LAN 1 will require 10 host IP addresses.

The BRANCH1 LAN 2 will require 10 host IP addresses.

The BRANCH2 LAN 1 will require 10 host IP addresses.

The BRANCH2 LAN 2 will require 10 host IP addresses.

The HQ LAN will require 20 host IP addresses.

The link from HQ to BRANCH1 will require an IP address for each end of the link.

The link from HQ to BRANCH2 will require an IP address for each end of the link.

(Note: Remember that the interfaces of network devices are also host IP addresses and are included
in the above addressing requirements.)

Task 1: Examine the Network Requirements.

Examine the network requirements and answer the questions below. Keep in mind that IP addresses will
be needed for each of the LAN interfaces.
How many subnets are needed? 7
What is the maximum number of IP addresses that are needed for a single subnet? 20
How many IP addresses are needed for each of the branch LANs? 10
What is the total number of IP addresses that are needed? 64

Task 2: Design an IP Addressing Scheme.

Step 1: Subnet the 192.168.9.0 network into the appropriate number of
subnets. What will the subnet mask be for the subnetworks? 255.255.255.224
How many
usable host IP addresses are there per subnet? 30
Fill in the following chart with the subnet information.
Subn
et
Num

Subnet
Address

First
Usable
Host

Last
Usable
Host

Broadc
ast
Addre

CCNA Exploration
Routing Protocols and Concepts:
Introduction to Dynamic Routing Protocols

0
1
2

192.168.9.0
192.168.9.32
192.168.9.64

192.168.9.1
192.168.9.33
192.168.9.65

Activity 3.5.2: Subnetting Scenario 1

192.168.9.30
192.168.9.62
192.168.9.94

192.168.9.31
192.168.9.63
192.168.9.95

Subnet
3
4
5
6
7

Subnet
Address
Broadcast
Address Number

192.168.9.96
192.168.9.128
192.168.9.160
192.168.9.192
192.168.9.224

First Usable
Host Address

192.168.9.97
192.168.9.129
192.168.9.161
192.168.9.193
192.168.9.225

Last Usable
Host Address

192.168.9.126
192.168.9.158
192.168.9.190
192.168.9.222
192.168.9.254

192.168.9127
192.168.9.159
192.168.9.191
192.168.9.223
192.168.9.255

Step 2: Assign the subnets to the network shown in the Topology Diagram.
When assigning the subnets, keep in mind that routing will need to occur to allow information to be sent
throughout the network. The subnets will be assigned to the networks to allow for route summarization on
each of the routers.
1. Assign first subnet (lowest subnet) to the LAN connected to the Fa0/1 interface of BRANCH2.
What is the subnet address? 192.168.9.0/27
2. Assign second subnet to LAN connected to the Fa0/0 interface of BRANCH2. What is the subnet
address? 192.168.9.32/27
3. Assign third subnet to LAN connected to the Fa0/0 interface of BRANCH1. What is the
subnet address? 192.168.9.64/27
4. Assign fourth subnet to LAN connected to the Fa0/1 interface of BRANCH1. What is the
subnet address? 192.168.9.96/27
5. Assign fifth subnet to the WAN link from HQ to BRANCH1. What is the subnet address?
192.168.9.128/27
6. Assign sixth subnet to the WAN link from HQ to BRANCH2. 192.168.160/27
7. Assign seventh subnet to LAN connected to the Fa0/1 interface of HQ. What is the
subnet address? 192.168.9.192/27
Note: The highest subnet will not be required in this topology.

Task 3: Assign IP Addresses to the Network Devices

Assign the appropriate addresses to the device interfaces. Document the addresses to be used in the
Addressing Table provided under the Topology Diagram.
Step 1: Assign addresses to the HQ router.
1. Assign the first valid host address in the HQ LAN subnet to the LAN interface.
2. Assign the first valid host address in link from HQ to BRANCH1 subnet to the S0/0/0 interface.
3. Assign the first valid host address in link from HQ to BRANCH2 subnet to the S0/0/1 interface.
Step 2: Assign addresses to the BRANCH1 router.
1. Assign the first valid host address in the BRANCH1 LAN 1 subnet to the Fa0/0 LAN interface.
2. Assign the first valid host address in the BRANCH1 LAN 2 subnet to the Fa0/1 LAN interface.
3. Assign the last valid host address in link from HQ to BRANCH1 subnet to the WAN interface.
Step 3: Assign addresses to the BRANCH2 router.
1. Assign the first valid host address in the BRANCH2 LAN 1 subnet to the Fa0/0 LAN interface.
2. Assign the first valid host address in the BRANCH2 LAN 2 subnet to the Fa0/1 LAN interface.

3. Assign the last valid host address in link from HQ to BRANCH2 subnet to the WAN interface.
Step 4: Assign addresses to the host PCs.
1. Assign the last valid host address in the HQ LAN subnet to PC1.
2. Assign the last valid host address in the BRANCH1 LAN 1 subnet to PC3.
3. Assign the last valid host address in the BRANCH1 LAN 2 subnet to PC2.
4. Assign the last valid host address in the BRANCH2 LAN 1 subnet to PC4.
5. Assign the last valid host address in the BRANCH2 LAN 2 subnet to PC5.

Task 4: Test the Network Design.

Apply your addressing scheme. Check to see that all devices on directly connected networks can ping
each other.

Task 5: Reflection
How many IP address in the 192.168.9.0 network are unused or unusable in this design? 192
What would the command be to add a default static route on the WAN interface of the BRANCH1 router?
Ip route 0.0.0.0.0.0.0.0 Serial0/0

Can both of the BRANCH1 LANs be summarized into one route on the HQ router? S
What would be the command used to add this summary route to the routing table?
Ip route 192.168.9.64 255.255.255.192 Serial0/0

Can both of the BRANCH2 LANs be summarized into one route on the HQ router? S
What would be the command used to add this summary route to the routing table?
Ip route 192.168.9.0 255.255.255.192 Serial0/1

Can the HQ LAN and both of the BRANCH1 LANs be summarized into one route on the BRANCH2
router? This summarized route should also include the link between the HQ and BRANCH1 routers.

What would be the command used to add this summary route to the routing table?