Scribd
Upload
699 views

Loading of Telephone Cable Circuits

loading

Uploaded by

Merlin Gilbert Raj
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
699 views

Loading of Telephone Cable Circuits

loading

Uploaded by

Merlin Gilbert Raj
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Standard Telephones and Cables Limited

COMMUNICATION
CABLES

A British Company of ITT

Loading of
Telephone Cable Circuits
Introduction
This leaflet is intended as a brief guide to the
selection and application of loading (the insertion, of coils as lumped inductance) to telephone
circuits to meet specified transmission requirements of attenuation, impedance and frequency
band.
The guide is sufficient only to illustrate the effect
of the amount of inductance added per unit
length of circuit in conjunction with the distance
between loading coils, variation of circuit capacitance, etc. Loading is, in general, confined to
voice-frequency circuits and the information in
this leaflet applies to these. However, special
loading is sometimes applied to carrier entrance
cables, to broadcast music circuits and to intermediate cables in open wire routes.
STCs Telephone Cable Division will be glad to
give further information and to advise on suitable
loading for any specific scheme.
Loading is normally applied for one or more of
three reasons.

To reduce the circuit attenuation.


To match a given impedance.
To equalise the attenuation over a specified frequency band.

Loading will also affect the circuit crosstalk (due


to changed impedance as well as by possible coil
to coil crosstalk) and will limit the transmitted frequency band by lowering the cut-off frequency.
The loading applied to a circuit is, therefore, often a compromise in order to attain the desired
improvement in one characteristic whilst maintaining others at acceptable values.
Nowadays, and particularly with star-quad cables, it is usual to load only the side or physical
circuits, employing one coil for each pair. If
phantom loading is required (generally applied
only to the phantom of a Dieselhorst-Martin multiple-twin quad) the loading unit consists of two
side circuit coils and one phantom circuit coil.

Attenuation (transmission loss) is a function of


the four primary parameters of a cable, Resistance (R), Capacitance (C), Inductance (L) and
Leakance (G), all per unit length.
In a modern cable, L and G are so small that
they can usually be considered negligible. R and
C are large, and are responsible for the major
portion of the attenuation. They are generally
determined by the economics of the system and
for any particular cable design a reduction of R
can only be attained by increase in conductor
size, and reduction of C by increasing the con-

ductor spacing resulting in a larger and more


expensive cable.
For a loaded cable, where G is very small, the
attenuation may be expressed approximately as
Attenuation =

R C
R 2C
=
2 L
4L

It is often impracticable to lower the attenuation


by reducing R or C and simpler to increase the
inductance (L) by the insertion of loading coils at
intervals. Although this is lumped loading (and
theoretically the inductance should be evenly
distributed along the line), in practice it is found
that coil loading gives quite acceptable overall
circuit characteristics provided that the inductances and the spacing of the coils are constant
within close limits.
It should be noted that a cable having a poor dielectric, or with water in the cable in any quantity,
will have a high mutual capacitance and probably
also a high leakance. Thus, not only is C high but
G is no longer negligible, resulting in a high attenuation. In such circumstances loading may
not be advantageous and G will have a very
marked effect as the cut-off frequency is approached.
Fig. 2 illustrates the characteristics of two normal
cables, typical in their values of R and C with
values of L, and the various curves indicate the
effect on attenuation of altering each of these
characteristics. Fig. 3 shows the attenuation of a
non-loaded circuit and the improvement obtained
by loading with 66 and 88 mH coils at a spacing
of 1830 metres, these being the most common
loading system for new installations.

Fig. 4 gives examples of the variation of cut-off


frequency with the cable mutual capacitance, the
inductance of loading coils and the coil spacing.
Fig. 5 shows a convenient method of relating
loading inductance, loading spacing and cut-off
frequency for a given circuit capacitance.

Cut-off Frequency
An effect of coil loading is to reduce the attenuation at low frequencies and to equalise the loss
over most of the voice frequency band. At the top
end of this band the approximate formula for attenuation is no longer valid and the effect of the
loading coils is that the attenuation rises steeply
to the so-called cut-off frequency where transmission over the circuit becomes impracticable.
This effect is shown in Fig. 3, as well as the advantage at the lower frequencies of loading.
A formula for the theoretical cut-off frequency (fc)
for a high quality loaded telephone cable is
fc =

LC

The effective transmission band is usually taken


as up to 0.75 of the cut-off frequency.

Impedance
Loading of a telephone line will normally increase
its characteristic impedance and, assuming a
loaded line of infinite length, the characteristic
impedance (Z0) is given approximately by the
following formula

Z0 =

L
C

where L and C represent the coil inductance and


pair capacitance per unit length of line (e.g. for
one loading section).
The cable impedance for various values of L and
C are given in Fig. 6 with 44 and 88 mH being
shown as examples of the many inductances that
may be used.
Fig 6 Nominal impedance variation with L, C and
coil spacing

Because the loading is lumped rather than the


ideal of being continuously distributed along the
cable length, the impedance frequency characteristic, as measured from the cable end, will
vary in shape (in both resistive and reactive
curves) according to the length of the section at
the end being considered.
It may therefore be necessary to consider the
end section when determining what impedance
shape is required and this is studied further under Spacing.

Spacing
In determining the spacing to be employed (the
distance between loading coils on any pair), several factors must be considered, i.e.

Attenuation
Cut-off frequency
Impedance
Crosstalk
Cost

As already explained, attenuation will generally


decrease with added inductance, but the amount
added is limited by cut-off considerations. A
higher cut-off with the same attenuation may be
attained by adding half-value loading coils at half
spacing, but this will affect impedance, crosstalk
and cost.

Crosstalk from capacitance unbalances (between


two circuits) is directly proportional to the circuit
impedances. Adding loading coils will increase
the impedance and therefore increase the cable
crosstalk as well as the possibility of crosstalk
between the coils themselves.
Cost, particularly where large numbers of coils
are involved, can be a considerable factor if a
short spacing between coils is used in order to
attain a high cut-off or other particular characteristics. Obviously all factors must be considered if
a truly economical loading is to be employed.
In laying out a route, consideration should be
given to the possibility of future extension. It is
desirable to make the two ends as near half sections (in length) as possible to give a convenient
terminating end impedance, and allow extensions to be started also in half sections to give a
complementary end impedance. To obtain these
conditions the average spacing may be varied
slightly throughout the route, but the length of
any loading section should not differ by more
than 1 % from (a) the average length of all full
sections; (b) the length of any adjacent full section.
Where it is not possible to achieve half-section
terminating conditions it is usual to consider each
route, together with any equipment at the terminals and other cables into which circuits may be
extended, and where necessary to fit building out
capacitors and loading coils at the terminals.
Some spacings have been coded for convenience and these are shown below

Code
Letter
A
B
C
D
E
F
H
K
M
R
W

Coil Spacing
Yards
233
1000
310
1500
1858
930
2000
2470
3000
3870
13870

Ft
700
3000
930
4500
5575
2790
6000
7400
9000
11600
41600

Metres
213
915
283
1372
1700
850
1830
2256
2745
3536
12680

When referred to a loading system the spacing


code letter is followed first by the inductance of
the side circuit, in milli-Henrys and then that of
the phantom circuit, if this is also loaded.

e.g.
H-66 denotes 66 mH side circuit coils at 1830 m
spacing.
B-66-27 denotes 66 mH on side circuits, 27 mH
on phantom circuits, both at 915 m spacing.
CE-5-12 denotes side circuit loading of 5 mH at
283 m and phantom circuit loading of 12 mH at
1700 m.

Phantom loading
Loading of the phantom circuit in addition to the
two side circuits of a quad was a practice applied
for many years to Multiple Twin quads, when all
three circuits were employed directly for long
distance speech. Although still employed in some
areas, it is a practice which has been slowly dying since the introduction of the star-quad, where
the mutual capacitance of the phantom circuit is
high, and the phantom is often used for other
purposes in its non-loaded state. However,
where phantom loading is employed it takes the
form of a three coil unit arranged as shown in
Fig. 7.

This is a specialised, and at times complex, problem, each project being considered for its several
requirements. Coil spacings are often based on a
capacitance rather than a physical distance and
full particulars of each route are needed to enable a study to be made. Carrier loading is sometimes applied to entrance cables from open wire
carrier systems, or on similar systems where a
short intermediate cable replaces a section of
open-wire route. These are instances where
loading is primarily designed for impedance considerations rather than to attain a low attenuation.

Broadcast loading
On these circuits a light loading is normally employed with the object of attaining a degree of
equalisation over a wide frequency band. Since
the circuits have to cater for the transmission of
both speech and music a high cut-off is required,
necessitating both light loading and usually a
close spacing of the loading coils.

Coil size
Although the electrical qualities of loading coils
meet all the desired electrical characteristics, coil
winding techniques and core materials are under
constant development to achieve a physically
smaller and more economic coil.
A loading coil case for installation in a manhole
can contain up to 1040 voice-frequency coils,
whilst up to 104 individual coils, fixed to a simple
support frame, can be accommodated within the
sleeve of a main cable joint.
STC anticipate that future loading coils will be
even smaller enabling the same sized loading
coil case, or cable joint, to house an even greater
number of coils.

Standard Telephones and Cables Limited


A British Company of ITT

Telephone Cable Division


North Woolwich London E16 2EJ
Telephone: 01-476 1401 Telex: 21645 Cablegrarns: Relay London WC2

1974 Standard Telephones and Cables Limited

Southern Press (Printers) Ltd. Purley Surrey

You might also like