Scribd
Upload
885 views

ENodeB FDD MML Script

The document provides a series of commands to configure an eNodeB by: 1) disabling DHCP and setting the local IP address; 2) removing default configurations; 3) adding and configuring devices, modules, ports and other resources; 4) configuring timing, synchronization, transport and security settings; and 5) adding sectors, operators and configuring cell and eRAN sharing.

Uploaded by

GauravSwami
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
885 views

ENodeB FDD MML Script

The document provides a series of commands to configure an eNodeB by: 1) disabling DHCP and setting the local IP address; 2) removing default configurations; 3) adding and configuring devices, modules, ports and other resources; 4) configuring timing, synchronization, transport and security settings; and 5) adding sectors, operators and configuring cell and eRAN sharing.

Uploaded by

GauravSwami
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 4

//An eNodeB is initially configured in minimum configuration mode.

//To turn off the DHCP switch, run the following command:
SET DHCPSW: SWITCH=DISABLE;
SET LOCALIP: IP="192.168.5.234", MASK="255.255.248.0";
//To remove the original default configuration, run the following commands:
RMV RRU: CN=0, SRN=60, SN=0;
RMV RRU: CN=0, SRN=61, SN=0;
RMV RRU: CN=0, SRN=62, SN=0;
RMV RRU: CN=0, SRN=63, SN=0;
RMV RRU: CN=0, SRN=64, SN=0;
RMV RRU: CN=0, SRN=65, SN=0;
RMV RRU: CN=0, SRN=66, SN=0;
RMV RRU: CN=0, SRN=67, SN=0;
RMV RRU: CN=0, SRN=68, SN=0;
RMV RRU: CN=0, SRN=69, SN=0;
RMV RRU: CN=0, SRN=70, SN=0;
RMV RRU: CN=0, SRN=71, SN=0;
RMV RRUCHAIN: RCN=0;
RMV RRUCHAIN: RCN=1;
RMV RRUCHAIN: RCN=2;
RMV RRUCHAIN: RCN=3;
RMV RRUCHAIN: RCN=4;
RMV RRUCHAIN: RCN=5;
RMV RRUCHAIN: RCN=6;
RMV RRUCHAIN: RCN=7;
RMV RRUCHAIN: RCN=8;
RMV RRUCHAIN: RCN=9;
RMV RRUCHAIN: RCN=10;
RMV RRUCHAIN: RCN=11;
RMV BRD: CN=0, SRN=0, SN=0;
RMV BRD: CN=0, SRN=0, SN=1;
RMV BRD: CN=0, SRN=0, SN=2;
RMV BRD: CN=0, SRN=0, SN=3;
RMV BRD: CN=0, SRN=0, SN=4;
RMV BRD: CN=0, SRN=0, SN=5;
RMV BRD: CN=0, SRN=0, SN=6;
//To configure main devices, run the following commands:
ADD BRD: CN=0, SRN=0, SN=0,TYPE=USCU;
ADD BRD: CN=0, SRN=0, SN=3, TYPE=LBBP, WM=RAT_FDD;
ADD BRD: CN=0, SRN=0, SN=16, TYPE=FAN;
ADD BRD: CN=0, SRN=0, SN=19, TYPE=UPEU;
ADD RRUCHAIN: RCN=0, TT=CHAIN, BM=COLD, HCN=0, HSRN=0, HSN=3, HPN=0;
ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=LRRU, RXNUM=2, TXNUM=2, R
S=LO, ALMPROCSW=ON;
//To configure ALDs, run the following commands:
ADD RET: DEVICENO=0, DEVICENAME="RET", CTRLPORTCN=0, CTRLPORTSRN=60, CTRLPORTSN=
0, RETTYPE=SINGLE_RET, POLARTYPE=SINGLE, SCENARIO=REGULAR;
MOD RETSUBUNIT: DEVICENO=0, SUBUNITNO=1, CONNCN1=0, CONNSRN1=60, CONNSN1=0, CONN
PN1=R0A, CONNCN2=0, CONNSRN2=60, CONNSN2=0, CONNPN2=R0B;
MOD RETPORT: CN=0, SRN=60, SN=0, PN=RET_PORT, PWRSWITCH=ON, THRESHOLDTYPE=RET_ON
LY_MULTICORE;
ADD TMA: DEVICENO=1, CTRLPORTCN=0, CTRLPORTSRN=60, CTRLPORTSN=0, SUBUNITNUM=2, C
ONNCN1=0, CONNSRN1=60, CONNSN1=0, CONNPN1=R0A, CONNCN2=0, CONNSRN2=60, CONNSN2=0
, CONNPN2=R0B;
//To configure monitoring units, run the following commands:

ADD
ADD
ADD
SET

FMU: CN=0, MPN=0;


TCU: CN=0, MPN=1;
EMU: MPN=0;
ALMPORT: CN=0, SRN=40, SN=0, PN=0, SW=ON, AID=65033, PT=BOOL, AVOL=HIGH;

//To configure power modules, run the following commands:


ADD PMU: CN=0, PTYPE=APM30, MPN=0, LSDF=DISABLE;
ADD PSU: CN=0, SN=1;
ADD PSU: CN=0, SN=2;
ADD PSU: CN=0, SN=3;
ADD BATTERY: CN=0, BTYPE=VRLA_BAT, BC=1000, HTSDF=ENABLE, LVSDF=ENABLE;
//To configure time information, run the following commands:
SET TIMESRC: TIMESRC=NTP;
ADD NTPC: MODE=IPV4, IP="172.166.1.251", SYNCCYCLE=60, AUTHMODE=PLAIN;
SET TZ: ZONET=GMT+0800, DST=NO;
//To configure synchronization information, run the following commands:
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, IP="80.3.101.21", MASK="255.255.2
52.0";
ADD IPCLKLINK: ICPT=PTP, SN=7, CNM=UNICAST, CIP="80.3.101.21", SIP="172.168.49.4
9", PROFILETYPE=1588V2;
SET CLKMODE: MODE=MANUAL, CLKSRC=IPCLK;
//To configure transport resources, run the following commands:
ADD ETHPORT: SN=7, SBT=BASE_BOARD, PA=COPPER, SPEED=AUTO, DUPLEX=AUTO;
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, IP="80.3.101.21", MASK="255.255.2
52.0";
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=LOOPINT, PN=0, IP="8.10.10.60", MASK="255.25
5.255.255";
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=LOOPINT, PN=0, IP="8.10.10.61", MASK="255.25
5.255.255";
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=LOOPINT, PN=1, IP="8.10.10.62", MASK="255.25
5.255.255";
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=LOOPINT, PN=1, IP="8.10.10.63", MASK="255.25
5.255.255";
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=LOOPINT, PN=2, IP="8.10.10.64", MASK="255.25
5.255.255";
ADD IPRT: SN=7, SBT=BASE_BOARD, DSTIP="0.0.0.0", DSTMASK="0.0.0.0", RTTYPE=NEXTH
OP, NEXTHOP="80.3.101.1";
MOD ENODEB: ENODEBID=9527, MCC="460", MNC="02";
RST ENODEB:;
ADD CNOPERATOR: CnOperatorId=0, CnOperatorName="CnOP", CnOperatorType=CNOPERATOR
_PRIMARY, Mcc="460", Mnc="02";
ADD S1SIGIP: CN=0, SRN=0, SN=7, LOCIP="8.10.10.60", LOCIPSECFLAG=DISABLE, SECLOC
IPSECFLAG=DISABLE, LOCPORT=2910, SWITCHBACKFLAG=ENABLE;
ADD MME: MMEID=0, FIRSTSIGIP="172.169.1.5", FIRSTIPSECFLAG=DISABLE, SECIPSECFLAG
=DISABLE, LOCPORT=2910;
ADD S1SERVIP: CN=0, SRN=0, SN=7, S1SERVIP="8.10.10.61", IPSECFLAG=DISABLE;
ADD SGW: SGWID=0, SERVIP1="172.169.2.3", SERVIP1IPSECFLAG=DISABLE, SERVIP2IPSECF
LAG=DISABLE, SERVIP3IPSECFLAG=DISABLE, SERVIP4IPSECFLAG=DISABLE;
ADD X2SIGIP: CN=0, SRN=0, SN=7, LOCIP="8.10.10.62", IPSECFLAG=DISABLE, SECIPSECF
LAG=DISABLE, SWITCHBACKFLAG=ENABLE;
ADD X2SERVIP: CN=0, SRN=0, SN=7, X2SERVIP="8.10.10.63", IPSECFLAG=DISABLE;
ADD X2ENODEB: X2ENODEBID=21, FIRSTSIGIP="8.10.10.50", FIRSTIPSECFLAG=DISABLE, SE
CIPSECFLAG=DISABLE, SERVIP1IPSECFLAG=DISABLE, SERVIP2IPSECFLAG=DISABLE, SERVIP3I
PSECFLAG=DISABLE, SERVIP4IPSECFLAG=DISABLE, ENODEBID=1234;
ADD OMCH: IP="8.10.10.65", MASK="255.255.255.255", PEERIP="172.166.1.251", PEERM
ASK="255.255.255.255", BEAR=IPV4, SN=7, SBT=BASE_BOARD, BRT=NO;
ADD VLANMAP: NEXTHOPIP="80.3.101.1", MASK="255.255.248.0", VLANMODE=SINGLEVLAN,

VLANID=3721, SETPRIO=DISABLE;
ADD VLANCLASS: VLANGROUPNO=0, TRAFFIC=USERDATA, SRVPRIO=16, VLANID=3721;
ADD ACL: ACLID=3100;
ADD ACLRULE: ACLID=3100, RULEID=1, PT=IP, SIP="172.169.1.5", SWC="0.0.0.0", DIP=
"8.10.10.60", DWC="0.0.0.7", MDSCP=NO;
ADD PACKETFILTER: SN=7, SBT=BASE_BOARD, PT=ETH, ACLID=3100, MB=DENY;
//To configure security information, run the following commands:
ADD IKEPROPOSAL: PROPID=1, AUTHMETH=IKE_RSA_SIG, DHGRP=DH_GROUP2;
ADD IKEPEER: PEERNAME="ikepeer", PROPID=1, IKEVERSION=IKE_V2, IDTYPE=FQDN, REMOT
EIP="99.9.1.1", REMOTENAME="segw", DPD=PERIODIC;
ADD IPSECPROPOSAL: PROPNAME="ipsecprop", TRANMODE=ESP, ESPAUTHALG=MD5, ESPENCALG
=DES;
ADD ACL: ACLID=3000, ACLDESC="For IPsec";
ADD ACLRULE: ACLID=3000, RULEID=1, PT=IP, SIP="8.10.10.60", SWC="0.0.0.0", DIP="
0.0.0.0", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=2, PT=IP, SIP="8.10.10.61", SWC="0.0.0.0", DIP="
0.0.0.0", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=3, PT=IP, SIP="8.10.10.62", SWC="0.0.0.0", DIP="
0.0.0.0", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=4, PT=IP, SIP="8.10.10.63", SWC="0.0.0.0", DIP="
0.0.0.0", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=5, PT=IP, SIP="8.10.10.64", SWC="0.0.0.0", DIP="
0.0.0.0", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=6, PT=IP, SIP="8.10.10.65", SWC="0.0.0.0", DIP="
0.0.0.0", DWC="0.0.0.0", MDSCP=NO;
ADD IPSECPOLICY: SPGN="policy", SPSN=1, ACLID=3000, PROPNAME="ipsecprop", PEERNA
ME="ikepeer", LTCFG=LOCAL;
ADD IPSECBIND: SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, SPGN="policy";
ADD ACL: ACLID=3100, ACLDESC="For PacketFilter";
ADD ACLRULE: ACLID=3100, RULEID=1, PT=IP, SIP="172.169.1.5", SWC="0.0.0.0", DIP=
"8.10.10.60", DWC="0.0.0.7", MDSCP=NO;
ADD CERTMK: APPCERT="232_429new.pem";
MOD APPCERT: APPTYPE=IKE, APPCERT="232_429new.pem";
MOD APPCERT: APPTYPE=SSL, APPCERT="232_429new.pem";
ADD TRUSTCERT: CERTNAME="rootcerm.pem";
ADD CA: CANAME="C=CN, O=LTE OG, CN=RANinterim", URL="http://10.108.191.86:8080/p
kix/";
//To configure a sector, run the following command:
ADD SECTOR: SECN=0, GCDF=DEG, LONGITUDE=1000, LATITUDE=999, ANTM=2T2R, SECM=Norm
alMIMO, COMBM=COMBTYPE_SINGLE_RRU, CN1=0, SRN1=60, SN1=0, PN1=R0A, CN2=0, SRN2=6
0, SN2=0, PN2=R0B, ALTITUDE=300;
//To configure operator information, run the following commands:
MOD ENODEB: ENODEBID=9527, MCC="460", MNC="02";
RST ENODEB:;
ADD CNOPERATOR: CnOperatorId=0, CnOperatorName="CnOP", CnOperatorType=CNOPERATOR
_PRIMARY, Mcc="460", Mnc="02";
ADD CNOPERATORTA: TrackingAreaId=0, CnOperatorId=0, Tac=33;
//To configure eRAN sharing, run the following commands:
MOD ENODEBSHARINGMODE: ENodeBSharingMode=SHARED_FREQ;
RST ENODEB:;
ADD CNOPERATOR: CnOperatorId=1, CnOperatorName="CnOp1", CnOperatorType=CNOPERATO
R_SECONDARY, Mcc="460", Mnc="01";
ADD LICENSESHARINGPOLICY: CnOperatorId=0, MaxUserNumRate=50;
ADD LICENSESHARINGPOLICY: CnOperatorId=1, MaxUserNumRate=50;
MOD LICFLOWCTRLALG: UPRATIO=100, TRAFFICSHARETYPE=DEDICATE, OP1TRAFFICRATIO=50,
OP2TRAFFICRATIO=50, OP1TRAFFICSHARRATIO=50, OP2TRAFFICSHARRATIO=50;

ADD CNOPERATORTA: TrackingAreaId=1, CnOperatorId=1, Tac=33;


MOD CELLALGOSWITCH: LocalCellId=0, RanShareModeSwitch=ON;
//To configure a cell, run the following commands:
ADD CELL: LocalCellId=0, CellName="cell0", SectorId=0, FreqBand=7, UlEarfcnCfgIn
d=NOT_CFG, DlEarfcn=2850, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100, Ce
llId=100, PhyCellId=100, FddTddInd=CELL_FDD, RootSequenceIdx=0, CustomizedBandWi
dthCfgInd=NOT_CFG;
ADD CELLOP: LocalCellId=0, TrackingAreaId=0;
ADD CELLOP: LocalCellId=0, TrackingAreaId=1;
ACT CELL: LocalCellId=0;
//To configure neighboring cells, run the following commands:
MOD CELLALGOSWITCH: LocalCellId=0, FreqPriorityHoSwitch=FreqPriorIFHOSwitch-1&Fr
eqPriorIFBlindHOSwitch-1;
MOD ENODEBALGOSWITCH: AnrSwitch=IntraRatEventAnrSwitch-1&IntraRatFastAnrSwitch-1
&IntraRatAnrAutoDelSwitch-1;
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="02", eNodeBId=236, CellId=0, DlEarfcn=31
00, UlEarfcnCfgInd=NOT_CFG, PhyCellId=236, Tac=33;
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="02", eNodeBId=236, CellId=1, DlEarfcn=28
50, UlEarfcnCfgInd=NOT_CFG, PhyCellId=236, Tac=33;
ADD EUTRANINTERNFREQ: LocalCellId=0, DlEarfcn=3100, UlEarfcnCfgInd=NOT_CFG, Cell
ReselPriorityCfgInd=NOT_CFG, SpeedDependSPCfgInd=NOT_CFG, MeasBandWidth=MBW100,
PmaxCfgInd=NOT_CFG;
ADD EUTRANINTERFREQNCELL: LocalCellId=0, Mcc="460", Mnc="02", eNodeBId=236, Cell
Id=0;
ADD EUTRANINTRAFREQNCELL: LocalCellId=0, Mcc="460", Mnc="02", eNodeBId=236, Cell
Id=1;
//To turn on the DHCP switch, run the following command:
SET DHCPSW: SWITCH=ENABLE;

You might also like