CLI Management User Guide

Command Line Interface

For Management of Select Net to Net Micro DSLAMs and IP DSLAMs

210-0000052 rev01
Copyright 2002 Net To Net Technologies, Inc.
The Net To Net Logo is a trademark of Net To Net Technologies, Inc.

Worldwide Headquarters
Net To Net Technologies
112 Corporate Drive
Portsmouth, NH 03801
USA
+1 877-638-2638

210-0000052 rev 01

http://www.nettonet.com/
[email protected]

EMEA Headquarters
Net To Net Technologies
Victoria House 19 Park Way
Newbury Berkshire RG14 1EE
UK
+44 (0) 1635 570950

Contents
1.0 OVERVIEW
1.1 System Requirements
1.1.1
1.1.2
1.1.3
1.1.4
1.1.5

Straight-Through RJ45 to RJ45 Ethernet Cable

DB9 Female to RJ45 Male Adapter
Terminal Emulator
Telnet Tool
Trivial File Transfer Protocol (TFTP) Tool

1.2 Multi-User Support

1.3 Default Settings
1.3.1 CLI User Access Defaults
1.3.1.1 Read Only
1.3.1.2 Read/Write

1.3.2 System Defaults

1.3.2.1 IP Address
1.3.2.2 Other System Parameters

1.3.3 Port Defaults

1.4 Data Storage

1.4.1 Memory

1.4.1.1 RAM (Random Access Memory)

1.4.1.2 NVRAM (Non-Volatile Random Access Memory)

1.4.2 Local Files

1.4.2.1 Backup File
1.4.2.2 Template File

1.5 Data Management

1.5.1 IP DSLAM Data Management
1.5.1.1 Replacing an Interface Module
1.5.1.2 Replacing a Multiplexer Uplink Module (MUM)

1.5.2 Clearing NVRAM

1.5.2.1 Micro DSLAM

1.5.2.2 IP DSLAM

1.5.3 System Reset/Reboot

1.5.3.1 Manual
1.5.3.2 via CLI

2.0 Establish a PC to DSLAM Connection

2.1 Establish a Physical Connection
2.1.1 Plug the Provided Cable Adapter Into Your PC
2.1.2 Connect Your PC to the DSLAM COM Port

2.2 Launch Your Terminal Emulator

2.2.1 Log In
2.2.2 CLI Prompt

3.0 CLI COMMANDS

3.1 Overview
3.1.1 Command Syntax
3.1.2 Command Errors

3.1.2.1 Syntax Error

3.1.2.2 Slot and/or Port Number Error

3.1.3 Command History

3.1.3.1 Back
3.1.3.2 Forward

210-0000052 rev 01

3.2 SET Commands

3.2.1 System Configuration
3.2.1.1
3.2.1.2
3.2.1.3
3.2.1.4
3.2.1.5
3.2.1.6
3.2.1.7
3.2.1.8
3.2.1.9

CLI Session Timeout

Gateway
Inband Management
Inband Management VLAN ID
IP Address
Password
SNMP Community String
Subnet Mask
System Name

3.2.2 Port Configuration

3.2.2.1
3.2.2.2
3.2.2.3
3.2.2.4
3.2.2.5
3.2.2.6

Backbone-VLAN
Flood
Priority
VLAN Range
SDSL Line Code
Speed

3.3 SHOW Commands

3.3.1 SHOW Command Example
3.3.2 SHOW ALL
3.3.2.1 Micro DSLAM, IPD4000 with a MUM2000-2 or IPD12000 with a MUM2000-2
3.3.2.2 IPD12000 with two MUM2000-2s

3.3.3 Firmware Version

3.4 Independent Commands

3.4.1 System Management Regulation
3.4.1.1 Allow
3.4.1.2 Clear NVRAM
3.4.1.3 Reset
3.4.1.4 Enable Telnet (DEFAULT)
3.4.1.5 Disable Telnet
3.4.1.6 Enable TFTP (DEFAULT)
3.4.1.7 Disable TFTP
3.4.1.8 Enable Web Server (DEFAULT)
3.4.1.9 Disable Web Server
3.4.1.10 Who

3.4.2 HELP
3.4.3 LOGOUT

4.0 TECHNICAL SUPPORT

4.1 The Net to Net Web Site
4.2 Technical Support Engineers

210-0000052 rev 01

1.0

OVERVIEW

Net to Net Technologies' Micro DSLAMs and IP DSLAMs can be managed with Command Line Interface
(CLI) through either a direct PC to DSLAM COM (Communication) Port connection or from a remote network
connection via Telnet.
1.1

System Requirements
1.1.1

Straight-Through RJ45 to RJ45 Ethernet Cable

Required for establishing a direct connection from a Micro DSLAM or MUM2000-2 COM Port to
your PC for initial DSLAM configuration via CLI.
1.1.2

DB9 Female to RJ45 Male Adapter

Required for conversion of your PC's RS232 serial port for use with an RJ45 to RJ45 Ethernet
cable. Included with Micro DSLAMs and MUM2000-2s.
1.1.3

Terminal Emulator

Required for running CLI. Any standard terminal emulator currently on the market will serve the
purpose; there are no specific program requirements.
1.1.4

Telnet Tool

Required for remote DSLAM management with CLI. Microsoft Windows Operating Systems
(1998, 2000, NT and XP) include a Telnet tool which is run through the MS Command Prompt
(MS-DOS) program. If you are using an operating system other than Windows, you may need to
install a Telnet tool. Any standard Telnet tool currently on the market will serve the purpose;
there are no specific program requirements.
1.1.5

Trivial File Transfer Protocol (TFTP) Tool

Required for downloading DSLAM firmware updates and for saving DSLAM configurations to
local files for backup and/or template use. Any standard TFTP tool currently on the market will
serve the purpose; there are no specific program requirements.
1.2

Multi-User Support

Up to 10 CLI connections can run concurrently: 1 direct connection via the Micro DSLAM or
MUM2000-2 COM Port and up to 9 remote connections via Telnet. There are two classes of CLI
users: Superuser (read/write) and General User (read only). Both classes may be logged in
simultaneously.
1.3

Default Settings

No configuration is necessary for a Micro DSLAM or IP DSLAM to operate at default settings.

210-0000052 rev 01

1.3.1

CLI User Access Defaults

1.3.1.1

Read Only

Username:

"general"

Password:

"Password"

1.3.1.2

Read/Write

Username:

"superuser"

Password:

"Password"

NOTE Usernames and passwords are case sensitive.

1.3.2

System Defaults
1.3.2.1

192.168.254.252

IPD12000 Slot 14*:

192.168.254.253

IPD4000 Slot 5:

192.168.254.252

Micro DSLAM:

192.168.254.252

1.3.2.2

1.3.3

IP Address

IPD12000 Slot 13*:

Other System Parameters

Gateway:

0.0.0.0

Inband Management:

disabled

Inband Management VLAN ID:

0 (off)

Management IP Address Range:

0.0.0.0 - 255.255.255.255 (all)

Subnet Mask:

255.255.255.0

System Name:

[MUM or Micro DSLAM Model Name]

Telnet:

enabled

TFTP:

enabled

Web Server (NMS):

enabled

Port Defaults

Circuit Identification*:

1.4

*As a method of preventing duplicate IP

Address conflicts, default IP Addresses
for the IPD12000 are configured
according to the slot location of the
Multiplexer Uplink Module(s) (MUMs).

n/a (no default)

Backbone-VLAN:

0 (off)

Flood:

Uplink

IP Range 1*:

0.0.0.0 - 255.255.255.255

IP Range 2*:

0.0.0.0 - 0.0.0.0

Protocol*:

all traffic

VLAN Priority:

0 (none)

VLAN Range:

0-0 (off)

*These parameters cannot be

configured via CLI; they are
configurable only with Simple
Network Management Protocol
(SNMP) and Net to Net's Network
Management System (NMS).

Data Storage
1.4.1

Memory

Configuration backup is inherent in Net to Net Technologies' Micro DSLAMs and IP DSLAMs.
Upon initial power up, default parameters will remain in place unless changed through CLI,
SNMP (Simple Network Management Protocol) or NMS (Net to Net's Network Management
System). Once changed, new configurations will automatically be recorded in both RAM and
NVRAM:
210-0000052 rev 01

1.4.1.1

RAM (Random Access Memory)

Data stored in RAM will be erased if the DSLAM loses power.

1.4.1.2

NVRAM (Non-Volatile Random Access Memory)

Data stored in NVRAM will remain intact (even if the DSLAM loses power) unless
deliberately cleared or reconfigured.
1.4.2

Local Files

Both system and port configurations can be saved on your PC or local network as a backup
and/or for use as a template for future configurations. Once a DSLAM has been configured as
desired, the settings can be flash uploaded (from the DSLAM to a local file) through a Trivial
File Transfer Protocol (TFTP) tool with a GET command and the following information:
1.4.2.1

Backup File

A DSLAM backup file records ALL system and port configurations.

ITEM

DATA NEEDED FOR BACKUP

EXAMPLE

Host Name:

DSLAM IP Address (xxx.xxx.xxx.xxx)

185.172.164.144

Remote
filename:

NVR_BACKUP.BIN.[superuser
password]

nvr_backup.bin.Password

Local filename:

user preference

dslam27_mum13_backup.bin

1.4.2.2

Template File

A DSLAM template file records all system and port configurations EXCEPT IP ADDRESS.
ITEM
Host Name:

DATA NEEDED FOR TEMPLATE

EXAMPLE

DSLAM IP Address (xxx.xxx.xxx.xxx) 185.172.164.144

Remote filename: NVR_CFG.BIN.[superuser password]

nvr_cfg.bin.Password

Local filename:

n2n_dslam12000_template.bin

user preference

Configuration files can also be flash downloaded FROM a local file TO a DSLAM, simply replace
the GET command with a PUT command. Refer to your TFTP user manual for further
instruction.
NOTE If you have an IPD12000 with two MUMs (one each in Slots 13 and 14), backups must be done for each
MUM individually.

210-0000052 rev 01

1.5

Data Management
1.5.1

IP DSLAM Data Management

1.5.1.1

Replacing an Interface Module

IF THE REPLACEMENT
INTERFACE MODULE IS:

THEN MODULE CONFIGURATIONS

WILL REVERT TO:

the same model as the previous module and new

or unconfigured

the same configurations as the

previous module

the same model as the previous module and

already configured

the same configurations as the

previous module

a different model than the previous module and

new or unconfigured

original default settings (Section 1.3)

a different model than the previous module and

already configured

original default settings (Section 1.3)

A replacement module (of like model) will take on the same configurations as the
previous module only if the Multiplexer Uplink Module (MUM) remains in the chassis and
the chassis retains power during the interim. Otherwise replacement module
configurations will revert to original default settings.
1.5.1.2

Replacing a Multiplexer Uplink Module (MUM)

Net to Net Technologies recommends clearing the NVRAM of a previously configured

MUM before using it as a replacement in a different chassis (Section 1.5.2.2). Once
NVRAM has been cleared, the MUM will revert to original default settings.
IF THE REPLACEMENT MUM IS:

THEN CHASSIS AND INTERFACE MODULE

CONFIGURATIONS WILL REVERT TO:

the same model as the previous MUM

and new or unconfigured

the same configurations as the previous MUM

a different model than the previous

MUM and new or unconfigured

the same configurations as the previous MUM

A replacement MUM will take on the same configurations as the previous MUM only if
there is at least one interface module installed in the IP DSLAM and the IP DSLAM
retains power during the interim. Otherwise, the replacement MUM will revert to original
default settings.
1.5.2

Clearing NVRAM

Clearing NVRAM on the IP DSLAM or Micro DSLAM will restore ALL system and port
configurations to original default settings.
CAUTION Clearing NVRAM to restore original default settings includes restoring Net to Net's default IP

Address, Subnet Mask and Gateway. Additionally, Inband Management will revert to its original
default setting (OFF) and you will be required to establish a direct PC to DSLAM connection for any
subsequent configurations.

1.5.2.1

Micro DSLAM

Micro DSLAM NVRAM can only be cleared with the CLI CLEAR_NVRAM command; see
Section 3.4.1.2.

210-0000052 rev 01

1.5.2.2

IP DSLAM

Install the MUM you wish to clear into a powered IP DSLAM chassis devoid of interface
modules; if there are interface modules installed in the IP DSLAM, it is not necessary to
completely remove them, simply slide them out of the chassis far enough to disengage
the interface module connector at the back of the chassis and ensure that the power
LED on the interface module faceplate is no longer illuminated. Allow a minimum of one
[1] minute to pass with the MUM running in the chassis before reinstalling any of the
interface modules.
1.5.3

System Reset/Reboot

A system reset will clear Micro DSLAM or IP DSLAM interface module RAM and restore all port
configurations to original default settings. It does not clear NVRAM; system settings will remain
as configured. A system reset takes approximately one [1] minute to complete, after which you
will be required to log back in.
1.5.3.1

Manual

1.5.3.1.1

Micro DSLAM

Using a paperclip, mechanical pencil or similar tool, press and hold the Reset
Button on the chassis faceplate for 10 seconds.
1.5.3.1.2

IP DSLAM

1.5.3.1.2.1 MUM2000-2 only

Slide the MUM2000-2 you wish to clear out of the DSLAM chassis far enough
to disengage the module connector at the back of the chassis. Ensure the
power LED on the MUM2000-2 faceplate is no longer illuminated and wait
10 seconds before sliding the MUM2000-2 back into the chassis.
1.5.3.1.2.2 All DSLAM Modules
Power down the DSLAM chassis and wait 10 seconds before restoring power.
Resets all chassis interface modules in addition to the MUM2000-2.
1.5.3.2

via CLI

Use the CLI RESET command; see Section 3.4.1.3.

2.0

Establish a PC to DSLAM Connection

Initial configuration requires a direct physical connection from your PC to the Micro DSLAM or MUM2000-2
COM Port.
NOTE If your DSLAM has already been installed and configured, it can be managed with CLI via either a direct PC connection
(Section 2.1) or remotely via Telnet (Section 3.4.1.4).

2.1

Establish a Physical Connection

2.1.1

Plug the Provided Cable Adapter Into Your PC

Plug the provided DB9 Female to RJ45 Male Adapter into the RS232 serial port on your PC.
210-0000052 rev 01

The adapter pinout is as follows:

PIN SD20XX RJ45 PORT PINOUT DIRECTION PC RS232 SERIAL PORT PINOUT

2.1.2

Transmit Data

TxD

RxD

Receive Data

Data Set Ready

DSR

RTS

Request to Send

Clear to Send

CTS

DTR

Data Terminal Ready

Receive Data

RxD

TxD

Transmit Data

Ground

GND

GND

Ground

Data Terminal Ready

DTR

CTS

Clear to Send

Request to Send

RTS

DSR

Data Set Ready

No Connect

NC

DCD

Data Carrier Detect

Connect Your PC to the DSLAM COM Port

Connect one end of a STRAIGHT-THROUGH RJ45 TO RJ45 ETHERNET CABLE into the adapter
plugged into your PC, and the other end of the cable into the RJ45 COM Port located on the
front of the Micro DSLAM or MUM2000-2 faceplate.
2.2

Launch Your Terminal Emulator

Launch the Terminal Emulator on your PC and configure the program settings. Actual configurations
will depend upon the Terminal Emulator model type being used, though settings should be modeled
after the list below; most are standard defaults. Refer to your Terminal Emulator user manual for
further information.
Baud:

9600

Port:

Com 1

Bit:

Stop:

1 bit

Flow Control:

Software or XON/XOFF

Transmit Delay:

n/a

Parity:

none

2.2.1

Log In

Once your Terminal Emulator has been launched, the following information will appear on your
screen:
Net to Net Technologies
Copyright (C) [year]
[product model name] Version [number] (Boot Prom [number])
System Build Date: [date, time, year]
Mac Address: [address], IP Address: [address]

210-0000052 rev 01

This information will be followed by a request for username and, once username has been
entered, a request for password. You must log in as a Superuser in order to make
configuration changes.

2.2.2

Username:

"superuser"

Password:

"Password"

CLI Prompt

A command prompt will appear once you have logged in. The CLI command prompt is tied to
the DSLAM system name (Section 3.2.1.9). The default system name is the model name of the
MUM or Micro DSLAM into which you are logged.
[system name] ->

3.0

CLI COMMANDS
3.1

Overview
3.1.1
z

3.1.2

Command Syntax

Each CLI command must be typed in the sequence shown for that command
For all CLI commands requiring a slot number, the slot number should be entered as "1"
when configuring Micro DSLAMs
CLI commands are not case sensitive
The start and end values of a number range may be separated by either a space (" ") or
a dash (" - ")
A correctly entered command will be mirrored back to you, followed by the requested
data and/or a statement indicating the action taken
Command Errors
3.1.2.1

Syntax Error

Incorrect syntax (command format) will prompt an error message and the command will
not be carried out.
3.1.2.2

Slot and/or Port Number Error

A command with an incorrect slot and/or port number may not receive an error message
and/or may not be mirrored back to you. Incorrect slot and port numbers include slots
that are physically empty and slot or port numbers that are beyond the realm of possible
options.
CAUTION A command that is mirrored back to you has most likely been carried out. However, any command
NOT mirrored back to you has definitely NOT been carried out.

210-0000052 rev 01

3.1.3

Command History

The ten most recently entered CLI commands can be reviewed by pressing the and keys.
Each of these commands can also be altered for reuse: simply backspace on the chosen
command line to the point you wish to alter, type the updated information and press the Enter
Key.
3.1.3.1

Back

The Up Arrow Key () scrolls back from the most to the least recent of the last ten
commands entered.
3.1.3.2

Forward

The Down Arrow Key () Scrolls forward from the least to the most recent of the last ten
commands entered.
NOTE You can only scroll forward if you have already scrolled back; it is not possible to scroll forward
from the most recent command.

3.2

SET Commands

A SET command is used to configure slots and/or ports, either individually or as groups. The
following parameters are configured with SET commands:
SYSTEM CONFIGURATIONS

PORT CONFIGURATIONS

CLI Session Timeout

Password

Backbone-VLAN

VLAN Range

Gateway

SNMP Community String

Flood

SDSL Line Code

Inband Management

Subnet Mask

Priority

Speed

Inband Management VLAN ID

System Name

IP Address

NOTE All SET commands, with the exception of CLI Session Timeout and System Name, must be entered with a slot
number. Slot number should be entered as "1" for all Micro DSLAMs.

3.2.1

System Configuration

System configurations made to the MUM2000-2 apply to ALL ports in ALL slots of the IP
DSLAM. System configurations made to the Micro DSLAM apply to ALL ports on the Micro
DSLAM.
Unless your PC has been configured to accept Net to Net's default system settings, or initial
DSLAM configuration has already been completed, you will need to set a proprietary IP
Address, Subnet Mask and Gateway. If remote DSLAM management is desired via CLI, Net to
Net's Network Management System (NMS) and/or Simple Network Management Protocol
(SNMP), you must also set Inband Management. Additionally, if your network is running VLANs
to facilitate packet direction and/or promote packet security, you must also set Inband MGMT
(Management) VLAN ID. If any of these proprietary values are unknown, contact your System
Administrator or Information Technology Manager for further information. If you have an
IPD12000 with two MUMs, system settings for each MUM must be configured separately.
NOTE Configuration changes can be made with CLI at any time, regardless of IP Address, Subnet Mask and

Gateway settings, via a direct connection from the Micro DSLAM or MUM2000-2 COM Port to your PC.

210-0000052 rev 01

3.2.1.1

CLI Session Timeout

CLI Session Timeout sets the amount of time a CLI session can sit idle before the user is
automatically logged out. Time is represented in seconds; minimum is 30.
[system name] ->SET CLI_SESSION_TIMEOUT [xxx]
E.g.,

[system name] ->set cli_session_timeout 600

Default: 300 seconds (5 minutes)

3.2.1.2

Gateway

The proper syntax for a Gateway is xxx.xxx.xxx.xxx. The maximum allowable value for each
triple-digit quadrant is 255. The Gateway assigned to your DSLAM must duplicate that of
your PC.
[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for the Micro
DSLAM] DEFAULT_GATEWAY [xxx.xxx.xxx.xxx]
E.g.,

[system name] ->set slot 13 default_gateway 193.166.254.255

Default: 0.0.0.0
3.2.1.3

Inband Management

Inband Management allows remote DSLAM management via CLI, NMS and/or SNMP (as
applicable).
NOTE In order to remote manage a DSLAM via CLI, Telnet must also be enabled (Section 3.4.1.6).
[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for the Micro
DSLAM] INBAND_MANAGEMENT [ON, OFF]
E.g.,

[system name] ->set slot 13 inband_management on

Default: OFF
3.2.1.4

Inband Management VLAN ID

If your network is running VLANs to facilitate packet direction and/or promote packet
security, you must set Inband MGMT (Management) VLAN ID. Do not set Inband MGMT
VLAN ID if your network is not running VLANs.
[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for the Micro
DSLAM] INBAND_MGMT_VLAN_ID [0-4085]
E.g.,

[system name] ->set slot 13 inband_mgmt_vlan_id 100

Default: 0
NOTE Inband Management VLAN ID applies only to remote network management, it does not apply to
direct connections between your PC and the DSLAM COM or MGMT port.

3.2.1.5

IP Address

The proper syntax for an IP Address is xxx.xxx.xxx.xxx. The maximum allowable value for
each triple-digit quadrant is 255. The assigned IP Address must be in the same range as
210-0000052 rev 01

that of your PC but cannot duplicate it exactly: the first three triple-digit quadrants must
match your PC's IP Address, the fourth quadrant must be unique to the Micro DSLAM or
MUM2000-2 being configured.
[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for the Micro
DSLAM] IP_ADDRESS [xxx.xxx.xxx.xxx]
E.g.,

[system name] ->set slot 13 ip_address 193.166.254.98

Default: 192.168.254.xxx
xxx=252IPD12000 Slot 13, IPD4000 Slot 5, all Micro DSLAMs
xxx=253IPD12000 Slot 14
3.2.1.6

Password

Passwords may be alpha and/or numeric up to 15 case-sensitive characters in length.

You will be prompted for values. Only one password may be assigned per each class of
user: all general users utilize the same password and all superusers utilize the same
password.
NOTE General and Superuser passwords cannot be configured remotely via Telnet; CLI configuration of
passwords can only be accomplished via a direct connection from your PC to the Micro DSLAM or
MUM2000-2 COM port.

3.2.1.6.1

General User (Read Only)

General Users' access to DSLAM management via CLI is limited to the HELP [?],
LOGOUT and SHOW commands.
[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for
the Micro DSLAM] GENERAL_PASSWORD
E.g.,

[system name] ->set slot 5 general_password

Password: ********
Verify: ********

Default: "Password"
3.2.1.6.2

Superuser (Read/Write)

Superusers have unlimited access to DSLAM management via CLI.

[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for
the Micro DSLAM] SUPERUSER_PASSWORD
E.g.,

[system name] ->set slot 5 superuser_password

Password: ********
Verify: ********

Default: "Password"
3.2.1.7

SNMP Community String

SNMP community strings may be alpha and/or numeric up to 15 case-sensitive

characters in length. You will be prompted for values. Only one SNMP community string
may be assigned per each class of user: all read only users utilize the same community
string and all read/write users utilize the same community string.

210-0000052 rev 01

NOTE Read only and read/write SNMP community strings cannot be configured remotely via Telnet; CLI
configuration of SNMP community strings can only be accomplished via a direct connection from
your PC to the Micro DSLAM or MUM2000-2 COM port.

3.2.1.7.1

Read Only

Read only users are limited to SNMP GET requests.

[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for
the Micro DSLAM] SNMP_READONLY_COMMUNITY
E.g.,

[system name] ->set snmp_readonly_community

Community: ********
Verify: ********

Default: "Password"
3.2.1.7.2

Read / Write

Read/Write users have unlimited access to all supported SNMP Managment

Information Base (MIB) Object Identifiers (OIDs).
[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for
the Micro DSLAM] SNMP_READWRITE_COMMUNITY
E.g.,

[system name] ->set snmp_readwrite_community

Community: ********
Verify: ********

Default: "Password"
3.2.1.8

Subnet Mask

The proper syntax for a Subnet Mask is xxx.xxx.xxx.xxx. The maximum allowable value for
each triple-digit quadrant is 255. The Subnet Mask assigned to your DSLAM must
duplicate that of your PC.
[system name] ->SET SLOT [13 or 14 for the IPD12000, 5 for the IPD4000, 1 for the Micro
DSLAM] SUBNET_MASK [xxx.xxx.xxx.xxx]
E.g.,

[system name] ->set slot 13 subnet_mask 255.255.255.207

Default: 255.255.255.0
3.2.1.9

System Name

User defined identifier of up to 32 alpha-numeric characters; replaces model name as

the CLI command prompt.
[system name] ->SET SYSTEM_NAME [user defined]
E.g., [system name] ->set system_name dslam412_mum13
The command prompt would then appear as:
dslam412_mum13 ->

Default: MUM or Micro DSLAM model name

210-0000052 rev 01

NOTE CLI System Name is tied to the first 32 characters of the SNMP MIB-II OID sysName;
configuration of the system name via SNMP changes the CLI command prompt.

3.2.2

Port Configuration

The remainder of SET commands apply to each port within the IP DSLAM or Micro DSLAM
individually and may be configured independently for each subscriber line (if so desired).
3.2.2.1

Backbone-VLAN

A Backbone-VLAN tag is the primary packet identifier; it allows a router with backbone
capabilities to make smarter decisions, in directing unlearned traffic, by pointing packets
to the correct network clouds. Once the packets have made it to the proper network,
standard VLAN tags direct the packets to the intended ports.
PACKETS
COMING
FROM THE

WITH

WILL BE

WAN

both
BackboneVLAN & VLAN
tags

dropped, regardless of whether the Backbone-VLAN tag is in

accordance with current configurations.

WAN

standard
VLAN tags
only

transmitted in accordance with standard VLAN rules (Section

3.2.2.4). If the packet adheres to standard VLAN rules and
the Backbone-VLAN is currently configured, then a BackboneVLAN tag will automatically be added to the packet, prior to
transmission, along with the configured VLAN ID, configured
Priority and a zero [0] CFI bit.

uplink

both
BackboneVLAN & VLAN
tags

dropped if the Backbone-VLAN is not currently configured, or

if the Backbone-VLAN is configured but the packet's
Backbone-VLAN tag does not match the current configuration.
If the packet's Backbone-VLAN tag DOES match the current
configuration, the packet will follow standard VLAN rules
(Section 3.2.2.4).

uplink

standard
VLAN tags
only

dropped, if the Backbone-VLAN is currently configured. If the

Backbone-VLAN is NOT currently configured, then the packet
will follow standard VLAN rules (Section 3.2.2.4).

NOTE A Backbone-VLAN tag cannot be used independently; standard VLAN tags must be set (Section
3.2.2.4). Additionally, the DSLAM uplink connection for the port being configured must run
through a router in order for a Backbone-VLAN tag to function.

Backbone-VLAN = 0-4085
Default: 0 (disabled)
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the IPD4000, 1
for the Micro DSLAM] PORT [ALL or port number] BACKBONE_VLAN [0-4085]
E.g.,

3.2.2.2

[system name] ->set slot 2 port all backbone_vlan 100

Flood

Flood refers to the method in which interface modules handle unknown unicasts (traffic
directed to a single MAC Address), multicasts (traffic directed to multiple MAC
Addresses) and broadcasts (traffic directed to all MAC Addresses) for each port. The
Institute of Electrical and Electronics Engineers (IEEE) Virtual Local Area Network (VLAN)

210-0000052 rev 01

standard 802.1Q dictates that packets should be forwarded (flooded) if within the VLAN
range for that port.
3.2.2.2.1

Upl (Uplink - Default)

Unknown unicast, multicast and broadcast traffic is flooded only to the DSLAM's
uplink interface ports. This prevents communication between interface ports
without the intervention of an upstream device such as a router. If communication
between interface ports IS desired, the upstream device must be properly
configured to allow it.
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for the Micro DSLAM] PORT [ALL or port number] FLOOD UPL
E.g.,

3.2.2.2.2

[system name] ->set slot 2 port all flood upl

Vln (VLAN)

Unknown unicast, multicast and broadcast traffic (within the sender's VLAN range)
is flooded to both the uplink ports and the interface ports.
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for the Micro DSLAM] PORT [ALL or port number] FLOOD VLN
E.g.,

3.2.2.3

[system name] ->set slot 2 port all flood vln

Priority

In compliance with the IEEE 802.1p Standard (a subset of 802.1Q), each port can be set
with one of eight levels of prioritization designated numerically from 0 to 7: 0 denotes no
priority and 7 denotes the highest priority. This allows packets coming from ports
configured with higher priorities to scavenge bandwidth from lower priority ports if, or
when, bandwidth becomes scarce.
IF A PORT IS
CONFIGURED WITH

THEN

VLAN 0 (OFF)

the configured priority is irrelevant; the packet doesn't have

VLAN tags.

a Single VLAN (Access

Port)

the configured priority will automatically be added to the VLAN

tag and Backbone-VLAN tag (if utilized).

one or more VLAN

Ranges (Trunk Port)

the existing priority in the VLAN tag(s) and Backbone-VLAN tag

(if utilized) will automatically be replaced with the configured
priority.

Priority = 0 - 7
Default: 0 (no priority)
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the IPD4000, 1
for the Micro DSLAM] PORT [ALL or port number] PRIORITY [0-7]
E.g.,

3.2.2.4

[system name] ->set slot 4 port 3 priority 5

VLAN Range

Net to Net Technologies' IP DSLAMs and Micro DSLAMs comply with the Institute of
Electrical and Electronics Engineers (IEEE) Standard for Local and Metropolitan Area
Networks, specifically, the 802.1Q Virtual Bridge Local Area Networks Standard. VLAN
(Virtual Local Area Network) tags are a packet's primary identification unless used in
210-0000052 rev 01

conjunction with a Backbone-VLAN tag (Section 3.2.2.1). VLAN start and end tags
indicate the 802.1Q VLAN tag range to be supported for each port. Depending on your
Micro DSLAM or interface module model type, up to 10 VLAN ranges may be specified
per port, each of which may be configured with VLAN 0, a single VLAN or VLAN range.
NOTE When configuring VLAN Range(s) for a port, both Start and End VLAN tags must be entered for
ALL ranges, including single VLAN and VLAN OFF.

3.2.2.4.1

VLAN 0 / OFF

(DEFAULT)

VLAN mode is OFF when all possible VLAN ranges are configured at zero. Only
packets WITHOUT a designated VLAN tag are allowed to communicate across a
port with VLAN OFF.
PACKETS
COMING
FROM THE
WAN

WITH

WILL BE

no VLAN tag

transmitted

any VLAN tag dropped

uplink

no VLAN tag

transmitted

any VLAN tag dropped

Starting VLAN tag=0

Ending VLAN tag=0
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for Micro DSLAM] PORT [ALL or port number] VLAN_RANGE [1-10] 0-0
E.g.,

3.2.2.4.2

[system name] ->set slot 5 port 3 vlan_range 1 0-0

Single VLAN / Access Port

Any port configured with a single VLAN tag is automatically designated as an

802.1Q VLAN Access Port; only packets with the specified VLAN tag will be allowed
to communicate across that port.
NOTE Only ONE of a port's possible VLAN ranges may be set with a single tag for a port to be

considered an Access Port. If more than one VLAN range is configured for a port, whether
with single tags or ranges, the port automatically becomes a Trunk Port (Section
3.2.2.4.3).

210-0000052 rev 01

PACKETS
COMING
FROM THE

WITH

WILL BE

WAN

no VLAN tag

transmitted; the configured VLAN tag

will automatically be added to the
packet, prior to transmission, along
with the configured VLAN ID, configured
Priority and a zero [0] CFI bit.

WAN

any VLAN tag

dropped

uplink

no VLAN tag

dropped

uplink

transmitted; the VLAN tag will

the specified
automatically be removed from the
VLAN Access tag
packet prior to transmission.

uplink

a tag that does

not match the
dropped
configured VLAN
Access tag

Starting VLAN tag = 1-4085

Ending VLAN tag = Starting VLAN tag
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for the Micro DSLAM] PORT [ALL or port number] VLAN_RANGE [1-10]
[(1-4085) - (1-4085)]
E.g.,

3.2.2.4.3

[system name] ->set slot 5 port 3 vlan_range 1 100-100

VLAN Range / Trunk Port

A port set with one or more specified VLAN ranges will automatically be designated
as an 802.1Q VLAN Trunk Port; only packets tagged within the specified VLAN
range(s) will be allowed to communicate across that port. Up to 10 VLAN ranges
may be specified per port on select Micro DSLAM and interface module models.
NOTE A port configured with more than one single VLAN tag is considered a Trunk Port, not an
Access Port.

PACKETS
COMING
FROM THE

WITH

WILL BE

WAN

no VLAN tag

dropped

WAN

transmitted; the packet will retain its

a VLAN tag within the original VLAN tag, along with VLAN ID and
specified trunk port
CFI bit. The original Priority, however,
range
will automatically be replaced with the
DSLAM port's current Priority configuration.

WAN

a VLAN tag outside of

dropped
the trunk port range

uplink

no VLAN tag

uplink

a VLAN tag within the transmitted as is; the packet will retain
specified trunk port
its original tag configurations for VLAN ID,
range
Priority and CFI bit.

uplink

a VLAN tag outside of

dropped
the trunk port range

dropped

Starting VLAN tag = 1 - 4085

Starting VLAN tag < ending VLAN tag 4085
210-0000052 rev 01

[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for the Micro DSLAM] PORT [ALL or port number] VLAN_RANGE [1-10]
[(1-4085)-(1-4085)]
E.g.,

3.2.2.5

[system name] ->set slot 5 port 3 vlan_range 1 100-250

SDSL Line Code

SDSL Line Code refers to the method of line amplitude modulation for SDSL lines.
NOTE SDSL Line Code is currently configurable on SIM2000 interface modules and SDSL Micro

DSLAMs only; it is hard set on all other Net to Net SDSL products. Additionally, line code applies
to ALL ports on SIM2000s and Micro DSLAMs; it cannot be configured for individual ports.

3.2.2.5.1

G.SHDSL

(DEFAULT)

Transmission Convergence/Pulse Amplitude Modulation (TC/PAM) line code is a

sixteen-level PAM technique which incorporates advanced Trellis code, precoding,
spectral shaping, equalization circuits and forward error correction. Otherwise
known as G.SHDSL.
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for the Micro DSLAM] PORT [ALL or port number] SDSL_LINE_CODING
GSHDSL
E.g.,

3.2.2.5.2

[system name] ->set slot 2 port all sdsl_line_coding gshdsl

2B1Q

Two Binary, One Quaternary (2B1Q) line code is a four-level PAM technique which
reduces the signaling rate to half of the bit rate, thereby doubling transmission
efficiency.
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for the Micro DSLAM] PORT [ALL or port number] SDSL_LINE_CODING
2B1Q
E.g.,

3.2.2.5.3

[system name] ->set slot 2 port all sdsl_line_coding 2b1q

CAP

Carrierless Amplitude and Phase (CAP) line code modulates transmit and receive
signals into two wide-frequency bands that can pass throught a filter without being
attenuated.
[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the
IPD4000, 1 for the Micro DSLAM] PORT [ALL or port number] SDSL_LINE_CODING
CAP
E.g.,

3.2.2.6

[system name] ->set slot 2 port all sdsl_line_coding cap

Speed

The interface module or Micro DSLAM model type will determine the number of options
and individual speeds available for each port. Setting speed to OFF will disable the port.
See individual Interface Module User Guides and Micro DSLAM Installation Instructions
to obtain specific speed vs. distance capabilities and the default speed settings for each
model. When configuring bandwidth, speed must be expressed in kbps and entered as a
whole number followed by a "k".
Default: varies
210-0000052 rev 01

[system name] ->SET SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the IPD4000, 1
for the Micro DSLAM] PORT [ALL or port number] SPEED [xxxxk, OFF]
E.g.,

3.3

[system name] ->set slot 2 port all speed 528k

SHOW Commands

A SHOW command returns the current configuration of a requested parameter as identified by slot
number, port number and/or parameter name. Enter SHOW commands as you would SET
commands (Section 3.2): simply replace the word SET with the word SHOW and exclude
configuration values from the end of the command. The following parameter configurations can be
requested with a SHOW command:
Backbone-VLAN

Inband Management

Speed

CLI Session Timeout

Inband MGMT VLAN ID

Subnet Mask

Default Gateway

IP Address

System Name

Firmware Version

Priority

VLAN Range

Flood

SDSL Line Coding

NOTE All SHOW commands, with the exception of CLI Session Timeout and System Name, must be entered with a
slot number. The slot number should be entered as "1" for all Micro DSLAMs.

3.3.1

SHOW Command Example

A request for the current speed configuration of all ports in Slot 5 of an IPD12000 would be
entered as follows:
[system name] ->SHOW SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the IPD4000, 1 for
the Micro DSLAM] PORT [ALL or port number] SPEED
E.g., [system name] ->show slot 5 port all speed

A response to the above request would appear as follows:

Slot 5 Port 1 Speed = ____ kbps
Slot 5 Port 2 Speed = ____ kbps
Slot 5 Port 3 Speed = ____ kbps
Slot 5 Port 4 Speed = ____ kbps

The number of ports listed, and the speed shown

for each port, would depend upon the interface
module model type in slot 5 and the current speed
configuration as set for each port.

Slot 5 Port 5 Speed = ____ kbps

Slot 5 Port 6 Speed = ____ kbps
Slot 5 Port 7 Speed = ____ kbps
Slot 5 Port 8 Speed = ____ kbps
Slot 5 Port 9 Speed = ____ kbps
Slot 5 Port 10 Speed = ____ kbps
Slot 5 Port 11 Speed = ____ kbps
Slot 5 Port 12 Speed = ____ kbps

3.3.2

SHOW ALL

The SHOW ALL command lists current system configurations; it does not list port
configurations. The response varies slightly for an IPD12000 with two MUMs (Section 3.3.2.2).

210-0000052 rev 01

[system name] ->show

OR
[system name] ->show all

3.3.2.1

Micro DSLAM, IPD4000 with a MUM2000-2 or IPD12000 with a MUM2000-2

The response to a SHOW ALL command for a Micro DSLAM, a MUM2000-2 in an

IPD4000 (Slot 5) or one MUM2000-2 in an IPD12000 (either Slot 13 or Slot 14) will
appear as follows:
Slot [1, 5, 13 or 14] MUM Version:

[x.xx.xx]

Mac Address:

[xx-xx-xx-xx-xx-xx]

IP Address / Subnet Mask:

[xxx.xxx.xxx.xxx] / [xxx.xxx.xxx.xxx]

Default Gateway:

[xxx.xxx.xxx.xxx]

Inband Management

[ON or OFF]

Inband Mgmt VlanID:

[1-4085]

Allow Management from:

[xxx.xxx.xxx.xxx to xxx.xxx.xxx.xxx]

Web Server:

[Enabled or Disabled]

TFTP Server:

[Enabled or Disabled]

Telnet:

[Enabled or Disabled]

Cli Session Timeout:

[xxx]

3.3.2.2

IPD12000 with two MUM2000-2s

The response to a SHOW ALL command for an IPD12000 with two MUM2000-2s will list
select system configuration data for both MUMs. Allow Management from, Web Server,
TFTP Server and Telnet data, however, will only be listed for the ACTIVE MUM (the MUM
that you are logged into).
E.g., If there are two MUM2000-2s in your IPD12000 and you are logged into the system
via the MUM in Slot 13, the SHOW ALL response would appear as follows:

3.3.3

Slot 13 MUM Version:

[x.xx.xx]

Mac Address:

[xx-xx-xx-xx-xx-xx]

IP Address / Subnet Mask:

[xxx.xxx.xxx.xxx] / [xxx.xxx.xxx.xxx]

Default Gateway:

[xxx.xxx.xxx.xxx]

Inband Management

[ON or OFF]

Inband Mgmt VlanID:

[1-4085]

Allow Management from:

[xxx.xxx.xxx.xxx to xxx.xxx.xxx.xxx]

Web Server:

[Enabled or Disabled]

TFTP Server:

[Enabled or Disabled]

Telnet:

[Enabled or Disabled]

Cli Session Timeout:

[xxx]

Slot 14 MUM Version:

[x.xx.xx]

Mac Address:

[xx-xx-xx-xx-xx-xx]

IP Address / Subnet Mask:

[xxx.xxx.xxx.xxx] / [xxx.xxx.xxx.xxx]

Default Gateway:

[xxx.xxx.xxx.xxx]

Inband Management

[ON or OFF]

Inband Mgmt VlanID:

[1-4085]

Firmware Version

Firmware Version functions only as a SHOW command and cannot be entered as a SET
command.
210-0000052 rev 01

[system name] ->SHOW SLOT [ALL or 1-12 for the IPD12000, ALL or 1-4 for the IPD4000, 1 for
the Micro DSLAM] PORT [ALL or port number] FIRMWARE_VERSION
E.g.,

[system name] ->show slot 5 port all firmware_version

A response to the above request would appear as follows:

Slot 5 Port 1 MUX Version: ____,CONV Version: ____,
Slot 5 Port 2 MUX Version: ____,CONV Version: ____,
Slot 5 Port 3 MUX Version: ____,CONV Version: ____,
Slot 5 Port 4 MUX Version: ____,CONV Version: ____,

The number of ports listed,

and the firmware versions
shown for each port would
depend upon the interface
module model type in slot 5.

Slot 5 Port 5 MUX Version: ____,CONV Version: ____,

Slot 5 Port 6 MUX Version: ____,CONV Version: ____,
Slot 5 Port 7 MUX Version: ____,CONV Version: ____,
Slot 5 Port 8 MUX Version: ____,CONV Version: ____,
Slot 5 Port 9 MUX Version: ____,CONV Version: ____,
Slot 5 Port 10 MUX Version: ____,CONV Version: ____,
Slot 5 Port 11 MUX Version: ____,CONV Version: ____,
Slot 5 Port 12 MUX Version: ____,CONV Version: ____,

3.4

Independent Commands

The following CLI commands are used independently of the SET and SHOW commands.
3.4.1

System Management Regulation

3.4.1.1

Allow

Specifies the IP Address(es) from which a DSLAM may be remotely managed.

NOTE DSLAMs are always manageable via a direct physical connection with the MUM2000-2 or Micro
DSLAM COM (Communication) port, regardless of management IP Address specifications.

[system name] ->ALLOW [ALL, ip_address or ip_address ip_address]:

3.4.1.1.1

All IP Addresses

(DEFAULT)

[system name] ->allow

OR
[system name] ->allow 0.0.0.0 - 255.255.255.255

3.4.1.1.2

IP Address Range

[system name] ->allow [ip_address] - [ip_address]

E.g., [system name] ->allow 193.166.254.1 - 193.166.254.254

3.4.1.1.3

Single IP Address

[system name] ->allow [ip_address]

E.g., [system name] ->allow 193.166.254.102

210-0000052 rev 01

3.4.1.1.4

COM (Communication) Port Only

[system name] ->allow 0.0.0.0

Each ALLOW command entered overwrites all previously entered ALLOW commands.
3.4.1.2

Clear NVRAM

CAUTION Clearing Micro DSLAM or MUM2000-2 NVRAM restores ALL system and port configurations to
original default settings including IP Address, Subnet Mask and Gateway. Additionally,
Inband Management will revert to its original default setting (OFF) and you will be required
to establish a direct connection with your DSLAM for any subsequent configurations.

NVRAM cannot be cleared remotely via Telnet; your PC must be directly connected to the
Micro DSLAM or MUM2000-2 COM Port. Once the Clear NVRAM command has been
entered, the process will take approximately one [1] minute to complete and you will be
required to log back in for any subsequent configurations.
[system name] ->clear_nvram

3.4.1.3

Reset

Resets (reboots) the Micro DSLAM or IP DSLAM interface module(s), clearing RAM and
restoring all port configurations to original default settings. Resetting the DSLAM does
NOT clear NVRAM; system settings will remain as configured. A system reset takes
approximately one [1] minute to complete, after which you will be required to log back in.
[system name] ->reset

3.4.1.4

Enable Telnet

(DEFAULT)

Allows up to nine remote users to manage a DSLAM with CLI (via Telnet).
NOTE In order to remote manage a DSLAM via CLI, Inband Management must also be enabled (Section
3.2.1.3).

[system name] ->enable_telnet

3.4.1.5

Disable Telnet

Disallows remote DSLAM management with CLI (via Telnet).

[system name] ->disable_telnet

3.4.1.6

Enable TFTP

(DEFAULT)

Enables Trivial File Transfer Protocol (TFTP), allowing both system and port
configurations to be saved on your PC or local network as a backup and/or for use as a
template for future condfigurations (Section 1.4.2). TFTP also enables download of
firmware upgrades to your DSLAM (see Net to Net's DSLAM Firmware Upgrade
Procedure).
[system name] ->enable_tftp

3.4.1.7

Disable TFTP

Disables the option to download firmware upgrades, and to save system and port
configurations to local files.

210-0000052 rev 01

[system name] ->disable_tftp

3.4.1.8

Enable Web Server

(DEFAULT)

Allows DSLAM management via Net to Net Technologies' Network Management System
(NMS). See Net to Net's NMS Management User Guide.
[system name] ->enable_web_server

3.4.1.9

Disable Web Server

Disallows DSLAM management via NMS.

[system name] ->disable_web_server

3.4.1.10

Who

Returns the IP Addresses of all users currently logged on to the management system
through CLI and specifies whether each user is a Superuser or General User. Also
specifies which user, if any, is logged on via a direct connection through the DSLAM COM
port (as opposed to remote connections via Telnet).
[system name] ->who

3.4.2

HELP

The HELP command returns a list of CLI command possibilities.

[system name] ->help
OR
[system name] ->?

A response to either of the above HELP Commands would appear as follows:

Usage: [?, CLEAR_NVRAM, HELP, LOGOUT, WHO]
[DISABLE_TELNET, DISABLE_TFTP, DISABLE_WEB_SERVER]
[ENABLE_TELNET, ENABLE_TFTP, ENABLE_WEB_SERVER]
allow [ALL, IP_ADDRESS [IPADDRESS]]
[SET, SHOW] [CLI_SESSION_TIMEOUT, SYSTEM_NAME]
[SET, SHOW] SLOT [ALL, slotnumber] [PORT] [ALL, portnumber] ITEM VALUE
Slot is MANDATORY for all SET/SHOW commands
ITEMS

VALUES

------------------------------------

--------------------------------------

ALLOW

Allow IP_Address [IP_ADDRESS] (for mgmt)

BACKBONE_VLAN

[0-4085]

CLEAR_NVRAM

Reboots the unit and restores factory defaults

CLI_SESSION_TIMEOUT

Changes the CLI Session Inactivity Timeout

DEFAULT_GATEWAY

xxx.xxx.xxx.xxx

DISABLE_TELNET

Disables TELNET Capabilities

DISABLE_TFTP

Disables TFTP Server

DISABLE_WEB_SERVER

Disables the web server interface (NMS)

ENABLE_TELNET

Enables TELNET Capabilities

ENABLE_TFTP

Enables TFTP Server

ENABLE_WEB_SERVER

Enables the web server interface (NMS)

210-0000052 rev 01

FIRMWARE_VERSION

Displays the firmware version

FLOOD

[UPL, VLN]

GENERAL_PASSWORD

You will be prompted for values

INBAND_MANAGEMENT

[ON, OFF]

INBAND_MGMT_VLAN_ID

[0-4085]

IP_ADDRESS

xxx.xxx.xxx.xxx

LOGOUT

Logs user out of CLI

PRIORITY

[0-7]

RESET
SDSL_LINE_CODING

[GSHDSL, CAP, 2B1Q]

SNMP_READONLY_COMMUNITY

You will be prompted for values

SNMP_READWRITE_COMMUNITY

You will be prompted for values

SPEED

[XXXXk, OFF] where XXXX = speed (in kbps)

SUBNET_MASK

xxx.xxx.xxx.xxx

SUPERUSER_PASSWORD

You will be prompted for values

SYSTEM_NAME

Changes the DSLAM System Name and CLI Prompt

VLAN_RANGE

VLAN_RANGE: SHOW=[ALL, 1-10], SET=[1-10]

VLAN_ID: [0-4085]-[0-4085]

WHO

3.4.3

Who's logged on

LOGOUT

Logs users out of the DSLAM management system.

[system name] ->logout

4.0

TECHNICAL SUPPORT
4.1

The Net to Net Web Site

The following information can be found via the Technical Support page at nettonet.com:

4.2

Product Documentation:

http://www.nettonet.com/support/docs.cgi/

Frequently Asked Questions:

http://www.nettonet.com/support/faq/

Product Discontinuation Notices:

http://www.nettonet.com/support/disc/

DSL Distance and Bandwidth Chart:

http://www.nettonet.com/support/quickref.n2n

Firmware Downloads:

http://www.nettonet.com/support/downloads/

Visio Network Diagram Stencils:

http://www.nettonet.com/support/visio.n2n

Net to Net Enterprise MIBs:

http://www.nettonet.com/support/mibs/

Technical Support Engineers

If you are unable to locate the answers to your questions online, please contact Net to Net
Technologies' Technical Support Department directly:
North and South America

Europe, Middle East and Africa

[email protected]

[email protected]

1-(877)-638-2638

44-(0)-1635-570953

1-(603)-427-0600

210-0000052 rev 01