Scribd
Upload
86 views

Drawing 3 - Isometric

The document provides guidelines for dimensioning engineering drawings to produce clear and professional standards. It outlines general rules such as using narrow continuous lines for dimensions and wider lines for outlines. Dimensions should be placed outside outlines with small gaps and extension lines extending past dimension lines. Arrowheads should be uniform in size and touch dimension lines. Dimensions are written in millimeters with a minimum number of significant figures and decimals marked with a zero. Leader lines indicate specific features, terminating in arrows for points or dots within outlines. Dimensions are best placed to give the clearest understanding of a component's shape and size outside its profile if space permits.

Uploaded by

Pirene Zuniga
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
86 views

Drawing 3 - Isometric

The document provides guidelines for dimensioning engineering drawings to produce clear and professional standards. It outlines general rules such as using narrow continuous lines for dimensions and wider lines for outlines. Dimensions should be placed outside outlines with small gaps and extension lines extending past dimension lines. Arrowheads should be uniform in size and touch dimension lines. Dimensions are written in millimeters with a minimum number of significant figures and decimals marked with a zero. Leader lines indicate specific features, terminating in arrows for points or dots within outlines. Dimensions are best placed to give the clearest understanding of a component's shape and size outside its profile if space permits.

Uploaded by

Pirene Zuniga
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

ES 1 Engineering Drawing

Rules to dimensioning to produce a drawing to


comma positioned on the base line between the
a good professional standard.
figures, for example, 5,2 but never 5_2 with a
1. Dimension and extension lines are narrow
decimal point midway.
continuous lines 0.35 mm thick, if possible, clearly
placed outside the outline of the drawing. The 7. To enable dimensions to be read clearly, figures
drawing outline is depicted with wide lines of 0.7
are placed so that they can be read from the
mm thick. The drawing outline will then be clearly
bottom of the drawing, or by turning the drawing
defined and in contrast with the dimensioning
in a clockwise direction, so that they can be read
system.
from the right-hand side.
8. Leader lines are used to indicate where specific
2. The extension lines should not touch the outline of
indications apply. The leader line to the hole is
the drawing feature and a small gap should be
directed towards the centre point, terminating at
left, about 23 mm, depending on the size of the
the circumference in an arrow. A leader line for a
drawing. The extension lines should then continue
part number terminates in a dot within the outline
for the same distance past the dimension line.
of the component. The gauge plate here is
assumed to be part number six of a set of
3. Arrowheads should be approximately triangular,
inspection gauges.
must be of uniform size and shape and in every
case touch the dimension line to which they refer.
Arrowheads drawn manually should be filled in.
Arrowheads drawn by machine need not be filled
in.
4. Bearing in mind the size of the
and the fact that there may
together where limits of size
adequate space must be left
dimensions.

1st Semester

DIMENSIONING

actual dimensions
be two numbers
are quoted, then
between rows of

5. Centre lines must never be used as dimension


lines but must be left clear and distinct. They can
be extended, however, with the use of extension
lines.

Figure above shows a partly completed drawing of


a gauge to
illustrate the aspects of dimensioning.

When components are drawn in orthographic projection, a


choice often exists where to place the dimensions and the
following general rules will give assistance.
1. Start by dimensioning the view which gives the clearest
understanding of the profile or shape of the
component.
2. If space permits, and obviously this varies with the size
and degree of complexity of the subject, place the
dimensions outside the profile of the component as
first choice.
3. Where several dimensions are placed on the same side
of the drawing, position the shortest dimension
nearest to the component and this will avoid
dimension lines crossing.
4. Try to ensure that similar spacings are made between
dimension lines as this gives a neat appearance on the
completed drawing.
5. Overall dimensions which are given for surfaces that
can be seen in two projected views are generally best
positioned between these two views.
Figure shows a component which has been partly
dimensioned to illustrate some of the principles
involved.

6. Dimensions are quoted in millimetres to the


minimum number of significant figures. For
example, 19 and not 19.0. In the case of a decimal
dimension, always use a nought before the
decimal marker, which might not be noticed on a
drawing print that has poor line definition. We
write 0.4 and not .4. It should be stated here that
on metric drawings the decimal marker is a
Catanduanes State University
lecture notes by: Engr. L.J.T. Tonio

COLLEGE OF ENGINEERING

ES 1 Engineering Drawing

DIMENSIONING

Reference: Manual of Engineering Drawing : a guide to


ISO and ASME standards. - 3rd ed.

Catanduanes State University


lecture notes by: Engr. L.J.T. Tonio

COLLEGE OF ENGINEERING

1st Semester

You might also like