Module 4 (L12 - L18): Watershed

Modeling

Standard modeling approaches and classifications, system concept

for watershed modeling, overall description of different hydrologic
processes, modeling of rainfall, runoff process, subsurface flows
and g
groundwater flow

15 Watershed Modeling Approaches

1

L15 Watershed Modeling

L15

Topics Covered
Standard modeling approaches, System
concept Classifications,
concept,
Classifications Black box model,
model
Lumped model, Distributed model, Rainfall
runoff
ff modeling
d li

Keywords:
y
Watershed modeling,
g System
y
concept,
p
black box model, lumped model, distributed model.

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

Watershed Model - Introduction

0.0

15.00
12.00

5.0

9.00
10.0
6.00
6
00
15.0

3.00

Rainfall internsity
(m
mm/hr)

Watershed models - simulate

natural processes of the flow of
water, sediment, chemicals,
nutrients, and microbial organisms &
quantify the impact of human
activities on these processes.
Simulation of these processes plays
a fundamental
f d
l role
l in addressing
dd
a
range of watershed based water
resources, environmental, social &
economical problems.

Discharge(m3/sec)

20.0

0.00
0

200

400

600

Rainfall

Time(min)

Observed
Simulated

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

Watershed Model

Main tool in addressing a wide spectrum of

environmental and water resources problems
water resources planning, development, design,
operation, and management; flooding; droughts;
upland erosion; stream bank erosion; coastal
erosion; sedimentation; nonpoint source pollution;
water pollution from industrial, domestic,
agricultural, and energy industry sources;
migration of microbes; deterioration of lakes;
desertification of land; degradation of land; decay
of rivers; irrigation of agricultural lands;
conjunctive use of surface and groundwater;
reliable design of hydraulic structures and river
training works etc.
etc
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

System Approach

Surface water Groundwater

System Approach: problems involves 3 steps;

i) Describe the system involves modeling the
watershed
h d system; ii) Describe
D
ib the
h objective
bj
i
function
f
i
-
normally stated in terms of economic terms (eg.
Minimize flooding; iii) Optimize the system
Design problems classified: a) Long-run design of multiple
purpose reservoir system huge capital investment benefits
after & over a long time
Intermediate run irrigation & cultivation for a season
Short- run how much water to be released for flood control

Each require hydrologic modeling

Most situations alternative models
Models: criteria accuracy, simplicity, consistency & sensitivity
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

Classification of Models

Broadly classified into three types

Black Box Models: models describe mathematically the
relation between variables (eg.
(eg rainfall and surface runoff)
without describing the physical process by which they are
related. e.g. Unit Hydrograph approach; ANN; Rational
formula etc.
etc
Lumped models: These models occupy an intermediate
position between the distributed models and Black Box
Models. e.g. Soil Conservation Curve number method,
Stanford Watershed Model
Distributed Models: These models are based on complex
physical theory, i.e. based on the solution of real governing
equation. Eg: Model based on unsteady flow St. Venant
equations for watershed modeling.
modeling
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

Structure of Watershed Model

Si
Simulation
l i
off process that
h takes
k place
l
in
i watershed
h d

Aim: Ga
Gain be
better
e understanding
u de s a d g of
o hydrologic
yd o og c
phenomena operating in a watershed and how changes
in watershed may affect these phenomena
Watershed modeling steps:
1. Formulation
Rainf
Channel phase
2. Calibration/verification
/
all
flow
3. Application
Infiltration
Watershed model constitutes
Overland
fl
flow
1. Input function
2. Output function
3 Transform function
3.
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

Hydrologic Models - Types

Event vs. Continuous models

Event model : represents a single runoff event occurring over a

period
i d off time
i
ranging
i
f
from
about
b
an hour
h
to severall days
d
Accuracy of the model output - Depend on the reliability of
initial conditions
Continuous watershed model: will determine flow rates and
conditions during both, runoff periods and periods of no
surface runoff
Initial conditions must be known or assumed
Utilize runoff components: direct or surface runoff, shallow
surface flow (interflow) and groundwater flow
An event model may omit one or both of the subsurface
components and also evapotranspiration
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

Hydrologic Models Types

Complete vs. Partial Models
Complete or comprehensive watershed models
Solves the water balance equation
Represents more or less all hydrologic processes
Increases the accuracy of the model
Partial Models
Represents only a part of the overall runoff process
Ex: Water yield model gives runoff volumes but no peak
discharges
9

Hydrologic Models Types

Calibrated Parameter vs
vs. Measured Parameter
Models:

Calibrated parameter model:

One or more parameters that can be evaluated only by

fitting computed hydrographs to the observed hydrographs

Necessary
y - If the watershed component
p
has any
y
conceptual component models

Period of recorded flow is needed for estimating parameter

values
Measured parameter model:

Determination of parameters from known watershed

characteristics

Area and channel length Maps and channel cross sections

measured in the field

U
Usually
ll applied
li d tto ttotally
t ll ungauged
d watersheds
t
h d
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

10

Hydrologic Models Types

Lumped vs.
vs Distributed Models

Lumped models
Implicitly take into account the spatial variability of inputs, outputs, or
parameters
Utilize average values of the watershed characteristics affecting runoff
lead to significant error- due to nonlinearity and threshold values
Distributed models
Include spatial variation in inputs, outputs, and parameters.
Division of watershed area into a number of elements and calculation
of runoff volumes for each element

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

11

Hydrologic Models
Stochastic
Hydrologic models

Deterministic

Empirical model

Lumped

Semi distributed

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

Distributed

12

Hydrologic
Modeling

Precipitation

ET

ET

Interception &
Storage

Surface
Storage

Surface Runoff
Over land
Infiltration

Interflow

Percolation

Direct Runoff

GW Base
flow

Groundwater
Flow &
Storage

Channel Flow
& Processes

Flowchart of simple watershed model (Based on: McCuen

McCuen, 1989)
Direct runoff

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

13

Watershed Simulation Analysis

Model selection criteria
Assumptions & conceptualization
Ability of model to predict variables required by the
project
Hydrologic processes that need to be modeled to
estimate the desired outputs adequately (single-event
or continuous processes)
Availability of input data
Expertise available & computational facility
Price

Surface
detention

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

14

Watershed Simulation Analysis

Steps:

Selection of model
Input data collection: rainfall, infiltration, physiography,
land use, channel characteristics etc
Evaluate the study objectives under various watershed
simulation conditions
Selection of methods for obtaining basin hydrographs and
g
channel routing
Calibration and verification of model
Model simulations for various conditions
Sensitivity analysis
Evaluate usefulness of model and comment on needed
changes.
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

15

Estimation of Surface Runoff

Empirical Equations:
Rational method (Empirical model)
Q=C i A
or
q=0.0028 C i A
where, q=design peak runoff rate m3/s; C=Runoff
coefficient;
i=rainfall intensity (mm/hr) for design return period and for
a duration equal to time of concentration of the watershed;
A=watershed area in ha; C= Runoff coefficient (rate of peak
runoff rate to rainfall intensity, (dimensionless)); C varies
as per slope, land use etc. e.g. available -- 0.3 to 0.6 (0-5
% slope); - 0.1 to 0.3(0
0.3(0-5
5 % slope).
C1 A1 C2 A2 C3 A3

C
Watershed of different characteristics:
A

A A1 A2 A3
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

16

To help protect y our priv acy , PowerPoint prev ented this external picture from being automatically downloaded. To download and display this picture, click Options in the Message Bar, and then click Enable external content.

Disscharge(m3/sec)

Rational Method

5.0

9.00
10.0
6.00
15.0

3 00
3.00
0.00

20.0
0

200

400

600

Rainfall

Time(min)

Observed
Simulated

Assumptions: Rainfall occurs at uniform intensity, Tcequal to the time of concentration of watershed
R i f ll occurs att the
Rainfall
th uniform
if
intensity
i t
it over whole
h l area
Max. runoff is directly proportional to rainfall intensity
Peak discharge probability is same as rainfall probability
Runoff coefficient does not change with storm type
Time of concentration: It is the time needed for water
to flow from the most hydrological distant point in the
watershed to the outlet once the soil has become
saturated and minor depressions
p
filled

Surface
detention

12.00

Ra
ainfall internsity
(mm/hr)

0.0

15.00

When duration of rainfall storm equals time of

concentration, all parts of watershed contribute
y to the runoff at the outlet
simultaneously
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

17

Rational Method
Kirpich (1940) formula for Tc
where, Tc- in minutes
Tc 0.0195 L0.77 S g 0.385
L- Max. length of flow in m
Sg- Watershed gradient in m/m
(difference between outlet and most
remote point divided
d d db
by llength
hL
Modified Kirpich equation: Where, LoLength of overland flow in m
0.467

2
L
n
0.385
S0- Slope
Sl
along
l
path
h in m/m
/
Tc 0.0195L0.77 S g
o
So
n- Mannings roughness coefficient
g Poor g
grass,, cultivated raw crops
p n=0.2;;
Eg:

smooth impervious n=0.02

Rational method limited to area less

than 800 Ha
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

18

Other Empirical Equations

Surface water Groundwater

Q CA

0.75

Dickens formula:

where, Q Peak rate of surface runoff in m3/s

A Area in km2; C Coefficient e.g. 11.45 for annual
rainfall : 610 to 1270 mm
Ryves formula:
0.67

Q CA

Same Q and A and C varies from 6.76 to 40.5

depending on location of watershed (suitable for
South India)
Based on practical experience and long term
observations
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

19

Other Empirical Equations

Cooks method
Evaluated by relief, soil infiltration,
vegetation cover and surface storage
Approximate weightage are aligned for those
parameters

QPRF S
Where,Q Peak runoff for specific region;
P Peak runoff from groups;
R Geographic rainfall factor from groups
F Return
R
period
i d ffrom groups;
S shape factor from Table

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

20

Soil Conservation Service (SCS)

Method(1999)
Evolved for uniform rainfall using
assumptions for a triangular
hydrograph; Assumptions of rational
method and corresponding SCS
triangular hydrograph
Time for peak flow
Tp- Time of peak; D- Duration of excess
rainfall;
i f ll TL- Time
Ti
off L
Lag; Tc- Time
Ti
off
Concentration; Tc=TL /0.6
L- Longest flow length in m.
N- Runoff curve number and
Sg- average watershed gradient in m/m

Tp

D
D
TL 0.6Tc
2
2

1000
L
9
N

T
Tc
0.5
4407S g
0. 8

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

21

0.7

SCS Method
Peak flow rate(m3/s)

q qn AQ

qn= unit peak flow rate (m3/sec per

ha/mm of runoff)
A-Watershed area in ha
Q-Runoff depth in mm from curve
number method
Unit peak flow rates are developed for a
particular region using time of
concentration
i
and
d ratio
i off initial
i ii l
abstraction to 24 hour rainfall

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

22

Curve Number Method

Developed based on observation in agricultural

watersheds in USA for long timerainfall and runoff
by USDA.
SCS-CN method NRCS (Natural Resources
Conservation Service)
Based on recharge capacity of a watershed
Recharge
g capacity
p
y based on antecedent moisture
content and physical characteristics of watershed
Curve Number is an index that represents combination
of a hydrologic soil group and antecedent moisture
conditions

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

23

SCS-CN Method

Hydrologic
H
d l i Soil
S il Groups:
G
SCS(1972)
Group A (Low runoff potential):-Soil with high infiltration
rates
a es when
e thoroughly
o oug y wetted,
e ed, consisting
co s s g mainly
a y of
o deep
well to excessively drained sands and gravels
High rate of transmission
G
Group
B (Moderately
(M d
t l llow runoff
ff potential)
t ti l)
Moderate infiltration rates:-moderate rate of water
transmission
Group C (Moderately high runoff potential)
Slow infiltration rate
Group D (High runoff potential) slow infiltration
Eg. Clay pan or layer
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

24

SCS-CN Method
Antecedent Moisture Condition (AMC)
Index of watershed wetness which is determined by
total
runoff in 5 days period preceding a storm
AMC I
Lowest runoff potential
soil dry
y enough
g for cultivation
AMC II
Average condition
AMC III
Highest runoff potential
practically saturated

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

25

SCS-CN Method
Potential maximum retention storage of watershed is
related to curve number (Dimensionless); 0 to 100
Let
L t Ia is
i th
the initial
i iti l amountt off abstractions
b t
ti
(interception,
(i t
ti
depression storage & infiltration). It is assumed that
ratio of direct runoff Q and rainfall P minus initial loss
(P-Ia) is equal to ratio of actual retention to storage
capacity, S

Q
P Q Ia

P Ia
S

(1)

where, Ia -Initial amount of abstraction;

Ia is assumed to be a fraction of S on an average Ia=0.2S

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

26

SCS-CN Method

Therefore Equation (1) becomes

Therefore,

( P 0.2S ) 2
Q
P 0.8S

Knowing P and S, value of Q can be

Computed. Q has same units as P (in mm)
For convenience in evaluating antecedent rainfall, soil
conditions and land use practices, curve number

25400
CN
254 S
where, S- recharge capacity of watershed

Runoff

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

27

SCS-CN Method- Runoff CN for different hydrologic soil

Cover
Landd T
L
Treatme
t
Use or
nt or
cover practice
1
2
Fallow Straight
row
Row
R
crops
Row
crops

Straight
St
i ht
row
Straight
row

Hydrologic Groups
H d l i
Hydrologic

3
----

4
77

5
86

6
91

7
94

P
Poor

72

81

88

91

Good

67

78

85

89

condition

28

SCS-CN Method

Runoff

Above Table, given for antecedent rainfall condition

II ; Average condition
Various tables available for various conditions
Heterogeneous watershed may be divided into sub
areas with different numbers and then a weighted
curve number
b can b
be computed
d ffor those
h
watershed
h d
Also CN can be developed for local conditions
depending upon soil & other conditions.

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

29

SCS-CN Method

Relationship
R
l ti
hi b
between
t
rainfall
i f ll & runoff
ff curve number
b CN
(after Soil Conservation Service 1972)

30

Example Problem
Calculate the runoff from a watershed of 50 Ha for the
following
g data using
g SCS-CN method. Depth
p of
rainfall=150mm; Antecedent Moisture condition, AMC I. Row
crop, good condition in 30 Ha; Woodland, good condition in
20Ha.
Type of crop
CN at AMCII
AMCI
Row crop, good
82
82x0.8= 65.6
Woodland good
Woodland,
55
55x0 65= 35.75
55x0.65=
35 75
Weighted CN = (65.6 x 30 + 35.75 x 20)/ 50 = 53.66
Using CN 25400 ;
S= 219.35

254 S

( P 0.2 S ) 2
Q
P 0.8S

Q = 34.606 mm; Runoff in response to 150mm

rainfall

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

31

References
Raj Vir Singh (2000), Watershed Planning and
Management, Yash Publishing House
J.V.S
J V S Murthy (1991)
(1991), Watershed Management,
Management New Age
international Publications
Ghanshyam Das (2000), Hydrology and soil conservation
engineering, Prentice Hall
ll off India
d
http://en.wikipedia.org
http://www.fao.org
http://www fao org
Viessman and Lewis (2007), Introduction to Hydrology,
Pearson Education.

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

32

Tutorials - Question!.?.

Study the different types of models used for

runoff calculations for a given rainfall. Compare
th black
the
bl k box
b
models,
d l lumped
l
d models
d l and
d
physically based models, with advantages and
limitations of each.
For a typical watershed, compare various
Empirical equations available in literature for the
calculation
l l i
off runoff
ff for
f the
h given
i
rainfall.
i f ll
For a given rainfall depth, calculate the runoff
using each method & compare the results.
results
Get necessary standard values for each method
from the literature.
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay
33

Self Evaluation - Questions!.

Q

Why models are required for watershed planning &

management?.
Differentiate between black box models, lumped
models & distributed models.
What
h are the
h important model
d l selection
l
criteria in
watershed modeling?.
Discuss important Empirical equations used for runoff
calculations for a given rainfall.

P f T I Eldho,
Prof.
Eldh Department
D
t
t off Civil
Ci il Engineering,
E i
i
IIT Bombay
B b
34

Assignmentg
Questions?.
Q

Which are the different processes that can be

simulated using models in a watershed.
Differentiate between: a) event based & continuous
models; b) lumped & distributed models.
Illustrate
ll
the
h Rationall method
h d ffor runoff
ff estimation,
with its advantages & limitations.
Describe the SCS
SCS-CN
CN method for runoff estimation
with its advantages & limitations.

Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

35

Unsolved Problem!.

For your watershed area, for a given rainfall

depth, calculate the possible runoff using a)
R ti
Rational
lM
Method;
th d b) SCS
SCS--CN method,
th d and
d
compare the results.
From the topographical & land use details,
details obtain the
runoff coefficients for various areas & find the
average runoff coefficient based on literature values.
Based
d on the
h land
l d use pattern, and
d possible
bl
antecedent moisture conditions, identify the possible
curve number and get the weighted average.
Compute the runoff based on the average runoff
coefficient & curve number.
Prof. T I Eldho, Department of Civil Engineering, IIT Bombay

36

Dr. T. I. Eldho
Professor,
Department
p
of Civil Engineering,
g
g
Indian Institute of Technology Bombay,
Mumbai, India, 400 076.
Email: [email protected]
Phone: (022) 25767339; Fax: 25767302
http://www.civil.iitb.ac.in
http://www.
civil.iitb.ac.in

37