Professional Digital Two-Way Radio System
MOTOTRBO Mobile
Radio Installation Manual
DM 3400 Numeric Display Mobile
DM 3401 Numeric Display Mobile (with GPS)
DM 3600 Display Mobile
DM 3601 Display Mobile (with GPS)
Chapter 4 Options and Accessories Installation
4.1
Accessory Installation
The accessories must be installed through the rear accessory connector that is located on the rear of
the radio, adjacent to the power connector. Most of the Motorola-approved accessories are supplied
with female terminals crimped to a 20-gauge wire specifically designed to fit the plug of the rear
accessory connector.
Insert the female terminal into the accessory connector assembly in the appropriate locations. The
accessory connector assembly is provided together with the accessory. Connect the accessory
connector assembly to the rear accessory connector on the back of the mobile. Do not use other
generic terminals in the plug. Generic terminals can cause electrical intermittences and may cause
damage to the plug.
Rear Accessory
Connector
Figure 4-1 Location of the Rear Accessory Connector
4-2
Options and Accessories Installation Accessory Installation
Table 4-1 Rear Accessory Connector Pin Functions
Pin
No.
Pin Name
Pin Function
Pin
No.
Pin Name
Pin Function
1
2
USB+
USB-
14
15
Rx Audio
AUX Audio 2
Receive Live Audio2
PUBLIC Address 2
16
GND
Ground
USB/MAP_ID GND
MAP_ID_2
MAP_ID_1
SW B+
USB + (Data)
USB - (Data)
USB Power (5V from USB
accessory/cable)
USB/MAP_ID Ground
Accessory Identifier
Accessory Identifier
Switched Battery Voltage
VBUS
4
5
6
7
8
PWRGND
Ground
21
SPKR-
10
SPKR+
11
Tx Audio
12
Audio GND
Speaker - (3.2 ohm minimum
impedance)
Speaker + (3.2 ohm minimum
impedance)
Rear External Microphone
Input4
Audio Ground
13
AUX Audio 1
PUBLIC Address 1
17
18
19
20
GP5-1 (PTT)
5V Level GPIO, PTT Input1
GND
Ground
GP5-2 (Monitor) 5V Level GPIO, Monitor Input3
GP5-6
5V Level GPIO
5V Level GPIO, Channel
GP5-3
Activity Function
22
GP5-7
5V Level GPIO
23
EMERGENCY
Emergency Switch Input
24
GP5-7
5V Level GPIO
25
IGN SENSE
26
VIP-1
Ignition Sense5
12V Tolerant, 5V GPIO,
External Alarm
Pulling this line to ground will activate PTT function, activating the AUX_MIC input.
Fixed level (independent of volume level) received audio signal, including alert tones. Flat or de-emphasis are
programmed by CPS. Output voltage is approximately 330 mVrms per 1kHz of deviation.
3 This input is used to detect when a rear microphone accessory is taken off-hook, to override PL to alert the user to
busy traffic prior to transmitting.
4 This microphone signal is independent of the microphone signal on the front microphone connector. The nominal
input level is 80mVrms for 60% deviation. The DC impedance is 660 ohms and the AC impedance is 560 ohms.
5 See Figure 3-2 and Figure 3-8 for wiring information.
D-
USB / MAP_ID Ground
MAP_ID_1
Power Ground
Spkr+
Audio Ground
Rx Audio
Ground
Ground
GP5_6
GP5_7
GP5_8
VIP_1 (Ext Alarm)
10
12
14
16
18
20
22
24
26
11
13
15
17
19
21
23
25
D+
Vbus
MAP_ID_2
SW B+
Spkr-
Tx Audio
Aux Audio Out 1 / RxD
Aux Audio Out 2 / TxD
GP5_1 (PTT)
GP5_2 (Monitor)
GP5_3 (Chan Act)
Emerg Sw
Ign Sense
Figure 4-2 Pin Configuration of Rear Accessory Connector (as viewed from the rear of the radio)
August, 2008
6866575D26
Options and Accessories Installation Accessory Installation
4.1.1
4-3
Emergency Pushbutton or Footswitch Installation
Mount the emergency pushbutton (Motorola part number RLN5926_) or the footswitch (Motorola part
number RLN5929_) using the hardware that comes with the kit. Press the terminal into the accessory
connector housing. Connect the emergency switch wires to pins 23 and 18 (see Figure 4-3). Route
the finished cable from the switch location to the control head location.
NOTE 1
SPST NORMALLY OPEN
EMERGENCY SWITCH
PIN 23
PIN 18
USB / MAP_ID Ground
MAP_ID_1
Power Ground
Spkr+
Audio Ground
Rx Audio
Ground
Ground
GP5_6
GP5_7
GP5_8
VIP_1 (Ext Alarm)
10
12
14
16
18
20
22
24
26
11
13
15
17
19
21
23
25
Vbus
MAP_ID_2
SW B+
Spkr-
Tx Audio
Aux Audio Out 1 / RxD
Aux Audio Out 2 / TxD
GP5_1 (PTT)
GP5_2 (Monitor)
GP5_3 (Chan Act)
Emerg Sw
Ign Sense
D2
D+
ACCESSORY
CONNECTOR
Figure 4-3 Emergency Switch Wiring Diagram
6866575D26
August, 2008
4-4
4.1.2
Options and Accessories Installation Accessory Installation
Horn and Lights (External Alarm) Relay
For installations that use the horn/lights option, select a suitable location for mounting (normally
under the dash) and, referring to Figure 4-4, perform the following procedure:
1. Horn Relay Connect the relay contacts across the horn ring switch, typically found in the
steering column. Connect the two control wires (female pins) into locations 26 and 18 of the
connector.
2. Lights Relay Connect the relay across the headlamp ON/OFF switch, typically found in the
steering column. Connect the two control wires (female pins) into locations 26 and 18 of the
accessory connector.
D-
USB / MAP_ID Ground
MAP_ID_1
Power Ground
Spkr+
Audio Ground
Rx Audio
Ground
Ground
GP5_6
GP5_7
GP5_8
VIP_1 (Ext Alarm)
10
12
14
16
18
20
22
24
26
11
13
15
17
19
21
23
25
D+
Vbus
MAP_ID_2
SW B+
Spkr-
Tx Audio
Aux Audio Out 1 / RxD
Aux Audio Out 2 / TxD
GP5_1 (PTT)
GP5_2 (Monitor)
GP5_3 (Chan Act)
Emerg Sw
Ign Sense
Figure 4-4 Horn and Lights Wiring Diagram
August, 2008
6866575D26
MOTOROLA and the Stylized M Logo are
registered in the U.S. Patent and Trademark Office.
All other product or service names are the property
of their respective owners.
2007-2008 Motorola, Inc.
All rights reserved. June 2008.
www.motorola.com/mototrbo
@6866575D26@
6866575D26-C (Multilingual)
EN
DE
IT
FR
PL
ES
RU
