SD6109

VOLTAGE MODE PWM POWER SUPPLY WITH BUILT-IN SUPERVISOR,

PROTECTION AND REGULATION FOR PCs
DESCRIPTION
The SD6109 is a power management IC for computers.
It integrates various monitoring functions and protections, such as
AC fail detection, over power protection, negative voltage protection,
over/under voltage protection and provides power down signal for
PG.
Built-in high precision oscillator provides accurate protection and
delay time for monitoring. And internal regulators TL431 are used for
stable output 3.3V and 5V, with few peripheral components.

DIP-20-300-2.54

Built-in soft-start decreases stress of transformer against saturation.

SD6109 used for pull-push or half-bridge power system with high
efficiency and stability.

FEATURES
APPLICATIONS

* Advanced Bi-CMOS process.

* Switching mode power supply for

*4KV HBM ESD protection

* Bipolar structure adopted in Shunt regulators TL431, with high

computers.

reliability
* Over voltage protection for 3.3V/5V/12V
* Under voltage protection for 3.3V/5V/12V
* Over power protection
* Short circuit protection
* AC-input under voltage protection
* PG Circuit
* PSON for remote control
* Delay time for PSON or PG signals
* Two bypass regulators for 3.3V and 5V- voltage stability
* Soft start and maximum 93% duty cycle

ORDERING INFORMATION
Part No.

Package

Marking

SD6109

DIP-20-300-2.54

SD6109

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 1 of 11

SD6109

BLOCK DIAGRAM

ABSOLUTE MAXIMUM RATING

Characteristics

Symbol

Rating

Unit

Supply Voltage(pin 20)

VCC

12

Regulator Output At Pins FB1, FB2 Pins

VFB

16

Output Current At Pins PG, FB1, FB2 Pins

IOUT

30

mA

Power Dissipation(Tamb=25C)

PD

1.5

Power Dissipation(Tamb=90C)

PD

0.5

Thermal Resistance, Junction-To-Air

RJA

82.5

C/W

Operating Temperature Range

Tamb

-30 ~ +125

Storage Temperature Range

Tstg

-55~+155

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 2 of 11

SD6109

ELECTRICAL CHARACTERISTICS (Unless otherwise stated, VCC=5V, Tamb=25C)

Characteristics

Symbol

Test condition

Supply Voltage

VCC

All functions are normal.

Supply Current

ICC

PG High

Min.

Typ.

Max.

Unit

4.5

5.0

7.0

--

10

mA

Over-Voltage Protection 3.3V

VOVP1

3.9

4.1

4.3

Over-Voltage Protection 5V

VOVP2

5.8

6.1

6.5

Over-Voltage Protection 12V

VOVP3

13.9

14.5

14.9

Under-Voltage Protection 3.3V

VUVP1

2.0

2.6

2.8

Under-Voltage Protection 5V

VUVP2

3.0

3.6

3.9

Under-Voltage Protection 12V

VUVP3

6.0

7.2

8.0

Under-Voltage Sense 3.3V For PG Low

VUVS1

2.5

2.8

3.0

Under-Voltage Sense 5V For PG Low

VUVS2

4.0

4.3

4.5

Under-Voltage Sense 12V For PG Low

VUVS3

9.4

10.1

10.4

Over-Power Protection.

VOPPS

VUVAC = 1.5V

2.02

2.4

2.66

VNVP

1.9

2.05

2.2

INVP

RI = 75K

50

61

72

Timing For Over-Voltage Protection

tOVP

RI = 75K

0.5

0.7

1.3

ms

Timing For Under-Voltage Protection

tUVP

RI = 75K

0.9

2.4

3.8

ms

tUVS

RI = 75K

0.5

1.2

1.9

ms

Timing for Over-Power-Protection

tOPP

RI = 75K

4.0

7.0

10.0

ms

Timing for Negative Voltage Protection

tNVP

RI = 75K

4.0

7.0

10.0

ms

VREF

IFB = 0.5mA, Tamb = 25C 2.475

2.5

2.525

MV/V

VFB > 2V

10

mA

RI = 75K

200

300

400

ms

0.65

0.7

0.75

Negative Voltage Protection: Voltage

Level
Negative Voltage Protection: Source
Current

Timing For Under-Voltage Sense for

PG Low

Bypass

Reference Voltage

Regulator

Line Regulation

(FB1,VREF1, Output Sinking Current

FB2,VREF2) Capability
PG Delay
UVAC Voltage Sense for
PG
PG

REGLI-FB 4 < VFB < 16V

IOUT-FB
tPG
VUVAC

PG Output Rising Time

tR

CL = 100pF

us

PG Falling Time

tF

CL = 100pF

300

ns

VOL2

IPG = 5mA

0.5

ION2

VPG = 5V

PG Output Saturation
Level
PG Leakage Current
Collector

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 3 of 11

SD6109
Characteristics
PSON Input Threshold
Level
Remote Input Driving
Remote
Control

Current

Test condition

Min.

Typ.

Max.

Unit

VPSON

1.4

2.0

IPSON

0.5

mA

ms

Timing PSON to On/Off

On

tPSON(ON) RI = 75k

20

40

50

Off (PS-off)

tPSON(OFF)

10

20

30

4.8

6.5

ms

Timing PG low to Power

Off

tPSOFF

RI = 75k

Reference Voltage

V2.5

2.45

2.5

2.55

Input Bias Current

IIB

0.1

Error

Open-Loop Voltage Gain

Amplifier

Unity Gain Bandwidth

Power Supply Rejection
Ratio

Oscillator

Symbol

AVOL

50

60

dB

BW

0.3

MHz

50

dB

PSRR

PWM Frequency

FOSC

RI = 75k

60

65

70

kHz

Charge Current

ISS

RI = 75k

4.0

5.7

7.0

Duty Cycle

DC

85

93

Output Voltage Low

VOL

Io = 5mA

0.5

PWM

Output Voltage High

VOH

V12 = 12V

Output

Output Impedance of

RO

1.5

3.3

Soft-Start

VOH

PIN CONFIGURATIONS
1

20 VCC

V33

19 RI

V5

18 SS

OPP

17 IN

UVAC

NVP

V12

14 FB1

OP2

13 VREF1

OP1

12 VREF2

SD6109

PSON

PG 10

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

16 COMP
15 GND

11 FB2

REV:1.1

2009.02.23
Page 4 of 11

SD6109

PIN DESCRIPTIONS
Pin No.

Pin Name

I/O

Description

PSON

Remote switch input for CPU or controller. Control the PWM Output.

V33

3.3V over-voltage/under-voltage control sense input.

V5

5V over-voltage/under-voltage control sense input.

OPP

Over-power sense input.

UVAC

AC fail detection.

NVP

The protection input for negative output.

V12

12V over-voltage/under-voltage control sense input.

OP2

OP1

10

PG

11

FB2

Output of second converter regulation loop.

12

VREF2

Reference comparison input for second converter regulation loop. 2.5V.

13

VREF1

Reference comparison input for first converter regulation loop. 2.5V.

14

FB1

Output of first converter regulation loop.

15

GND

Ground.

16

COMP

I/O

17

IN

18

SS

I/O

19

RI

Connected to external resistor for the reference setting.

20

VCC

Supply voltage. It is connected to 5V-standby.

The totem-pole output drivers of push-pull PWM. The maximum duty

cycle (OP1 or OP2) is 46%.
The totem-pole output drivers of push-pull PWM.
PG logic output, 0 or 1 (open-collector). PG=1 means that the power is
good for operation.

Error amplifier output and the input of the PWM comparator.

The negative input of error amplifier. The positive input of error amplifier
is connected to 2.5V reference voltage.
The soft-start. It is settable through external capacitor. The current
source output at this pin is 5.7uA and the voltage is clamped at 2.5V.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 5 of 11

SD6109

FUNCTION DESCRIPTION
The SD6109 is a power management IC for computers. It integrates various monitoring functions and protections,
such as AC fail detection, over power protection, negative voltage protection, over/under voltage protection and
provides power down signal for PG. Built-in high precision oscillator provides accurate protection and delay time
for monitoring. And internal regulators TL431 are used for stable output 3.3V and 5V, with few peripheral
components. Built-in soft-start decreases stress of transformer against saturation. SD6109 used for pull-push or
half-bridge power system with high efficiency and stability.
1.

TIMING DIAGRAM

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 6 of 11

SD6109
2.

Remote Switch Control (PSON)

The PC generates the remote switch control signal which is connected to PSON. When the control signal is low,
PC power is on. And when the control signal is high, PC power is off..
3.

AC Fails Detection (UVAC)

The AC line voltage is coupled from the primary side to the secondary side through the main transformer, and
UVAC is connected to the secondary side by a resistor. When UVAC voltage drops below 0.7V and maintains
this situation over 200us, the PG signal will be pulled low , and it indicates that the AC line is power-down. The
voltage amplitude of the PWM switching signal from the secondary side is proportional to the AC line voltage.
Adjusting the ratio of the voltage divider can set the threshold for the power-down.

4.

Over Power Protection (OPP)

The over power protection is designed to detect over power and short circuit.. When the voltage of OPP is higher
than 2.4V and maintain this situation over 7msec, PG will be pulled low and the power outputs will be locked

5.

Negative Voltage Protection (NVP)

The negative voltage protection is designed to provide under voltage protection for negative voltage output.
Overload and short circuit can cause under voltage of negative voltage output.. When the voltage of NVP is
higher than 2.1V and this situation exists for longer than 7msec, the power outputs will be off and be locked.
Adjusting the resistor will set the threshold for locking the power outputs off. The threshold is determined by:
VNVP=INVP X (R1+R2)+V-12V
VNVP=INVP X R1+V-5V-0.7V

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 7 of 11

SD6109

TYPICAL APPLICATION CIRCUIT

Note: The circuit and parameters are for reference only, please set the parameters of the real application
circuit based on the practical test.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 8 of 11

SD6109

DETAIL APPLICATION CIRCUIT

AC
3
2
1

F1
5A/ 630V
RTHI SD15

VZ1
471
CX1
471nF/275AC

LF1
9mH

PFC

R5
2.2 1/2W

CX2
222nF/275AC (SA7257)

R6

C5
1 F/50V
D3
FR152 39 1/2W
C6
R8
1 F/50V
22 1/2W

R41
1.5K 1/4W

5VSB

R57
2K 1/8W

D4 FR152 R9 39 1/2W

D18
FR152

Q7
2SC945

Q1
2SC3320

BD1

KBU606

D1
FR107

D2
FR107

C1
C2
680 F/200V 680 F/200V

+12V

R11
4.7 2W

+12V

+5V

T1

R3
47 5W

ATEER35T1

C3
105K/250V
C4
222Z/1KV

NC

C16
103Z/200V

C15
103Z/200V

FB

D
PGND

VCC

SD484

C7
103V/1KV

D5
FR107

R10
100K 1/2W

R12
1.5M 1/4W
4
3
2
1

SGND

-5V

-12V

Uvac

+5V

PG

D7 IN4148
C8
104K/50V

R50
4.7K 1/8W

R51
47K 1/2W

C10
104K/50V

R47
100K 1/8W

24K 1/8W

R46

R49
100 1/8W

6.25K 1/8W

R53

R54
12K 1/8W

R55
12K 1/8W

R56
15.8K 1/8W

C33
104Z/50V

C34
104Z/50V

Q2
2SC3320

VR2
1K
1/10W

C32
103Z/100V

SD6109

R48
75K
1/8W

C31
401K
50V

ZNR2
ZNR1
TVR07241KS TVR07241KS

D25
IN4148

R25
R24
4.7 1/2W 4.7 1/2W

D11 FR152

L3

SD3A
F16C20C
FD2A
F16C20C
L
SD1A
SBL3040PT
SD2A
SBL3040PT
D9 FR152
SD2B
SBL3040PT
D10 FR152
FD2B
F16C20C
FD3B
F16C20C
D12 FR152

D26
FR152

Uvac

FD1
SB302
ATEEL19T7P7

L5
1.6#5.5TS

C19
L6
2200 F/16V 1.6#5.5TS

C18
2200 F/10V
C17
2200 F/10V

C22
680 F/16V

R27
47 1W

R29
270 1W

R28
100
1/2W

C20
2200 F/16V

R21
24K 1/8W

C26
103Z/100V

D15
FR152

D16
FR152

R37
620 1/8W

R30
1 2W

R36
1.8K
1/8W

+5VSB

R35
51 1/8W

R23
100 1/2W

Vref1

R34
1K 1/8W

C12
680 F/16V
C11
1000 F/10V

L1
R4*20

C27
105Z/50V

D13
C24
2200 F/10V FR152

R32
100 1/8W

L7
1.6#5TS

R31
4.7 1/2W

Vref2

Fb1

C25
0.47 F/50V

C13
104K/ 50V

R22
10K 1/8W

R19
510 1/8W

R18
47 1/8W

R33
22 1/8W

C23
2200 F/10V

C21
680 F/16V

L10P

L4
LT

Q5
KSA928A

Fb2

KPC817
D17
C14
T3
FR152
47 F/50V
FD5
SB302

U1

SD1B
SBL3040PT

D14 IN4148

R16
1K 1/8W

C9
22 3K/50V

R26
150 2W

R39
15 2W

R38
10 1/8W

C28
104Z/50V

+5V

+12V

-5V

-12V

+3.3V

+3.3VS

REV:1.1

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

T2
ATEE119 T8P2T2

D23
IN4148
R60
10 1/2W

R54
24K
1/8W

R45
27K
1/8W

VREF2

R20
251K 1/8W

R2
R1
330K/1/2W 330K/1/2W

OP1

Vref2
VREF1

Vref1
OP2

D24
IN4148

R44
1.5K
1/8W

UVAC COMP

R59
75K
1/8W

VP1
10K
1/10W

D20
+3.3V +5V
FR152
PSON

SS

3P

Q6
2SC945

C29
1 F/50V

C36
473/50V

R43
15K
1/8W

V5

Fb2
FB2
PG

D19
IN4148

R42
330
1/8W

C30
103Z
100V

IC1

D22
FR152

2009.02.23
Page 9 of 11

Http://www.silan.com.cn

RI

C35
473/50V

V33

Fb1
FB1
V12

IN
OPP

GND
NVP

VCC
POSN

D21
FR152

SD6109

PACKAGE OUTLINE
DIP-20-300-2.54

UNIT: mm

MOS DEVICES OPERATE NOTES:

Electrostatic charges may exist in many things. Please take following preventive measures to prevent effectively
the MOS electric circuit as a result of the damage which is caused by discharge:
z

The operator must put on wrist strap which should be earthed to against electrostatic.

Equipment cases should be earthed.

All tools used during assembly, including soldering tools and solder baths, must be earthed.

MOS devices should be packed in antistatic/conductive containers for transportation.

Disclaimer:

Silan reserves the right to make changes to the information herein for the improvement of the design and performance
without further notice!

All semiconductor products malfunction or fail with some probability under special conditions. When using Silan products
in system design or complete machine manufacturing, it is the responsibility of the buyer to comply with the safety
standards strictly and take essential measures to avoid situations in which a malfunction or failure of such Silan products
could cause loss of body injury or damage to property.

Silan will supply the best possible product for customers!

HANGZHOU SILAN MICROELECTRONICS CO.,LTD

Http://www.silan.com.cn

REV:1.1

2009.02.23
Page 10 of 11