Scribd
Upload
579 views

Discussion and Conclusion

This structural analysis examines a barbell made of A-36 steel. The material properties are obtained from references. Normal stress and deflection calculations are performed. The normal stress of 115.87 MPa is below the material yield strength of 400 MPa, indicating the barbell can safely support the applied loads. Buckling analysis is also conducted on a barbell stand, finding a critical stress of 415.61 MPa. Equilibrium equations are used to analyze forces at different structures of the equipment. The analysis concludes the equipment is safe to use based on the stress calculations being below reference values.

Uploaded by

Muse Sick
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
579 views

Discussion and Conclusion

This structural analysis examines a barbell made of A-36 steel. The material properties are obtained from references. Normal stress and deflection calculations are performed. The normal stress of 115.87 MPa is below the material yield strength of 400 MPa, indicating the barbell can safely support the applied loads. Buckling analysis is also conducted on a barbell stand, finding a critical stress of 415.61 MPa. Equilibrium equations are used to analyze forces at different structures of the equipment. The analysis concludes the equipment is safe to use based on the stress calculations being below reference values.

Uploaded by

Muse Sick
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Discussion

In this structural analysis of gymnasium equipment we have analysis the


barbell. The material for this equipment is A-36 steel. We have obtained the
references value of this material from the textbook. The ultimate stress for this
material is max= 400MPa. The modulus elasticity, E of this material is 200GPa
and modulus rigidity, G is 75GPa. Next, the yield strength is y= 250Mpa. We
have analysis the material with the weight 5 kg at barbell which is at structure 1,
10kg at structure 4, and 2.5 at structure 5.
We have analysis the equipment by using the appropriate calculation. The
main part of this equipment is the barbell which is structure 1. The barbell is
exerted by three forces which are P, Ra and Fbar. From the equilibrium equation
we use load, P (5kg) and Fbar (2kg) to get reaction force, Ra. Then, we have
calculate three forces to find the shear force and bending moment of the beam
to obtain shear and bending moment diagram. Firstly we draw the shear diagram
and then from the shear diagram we can draw the bending diagram. Area under
the shear curve between two points is equal to the change in bending moment
between the same two points.

Next, we use the bending moment diagram to get the maximum moment
so we can find the normal stress by using the equation:

M
S

By using the equation we get the normal stress equal to 115.87 MPa. The
reference value for maximum stress of the A-36 steel is 400 MPa. Since the
value obtained for the normal stress is smaller than the reference value for the
steel we used, we conclude that the barbell safely support the load to which it
will be subjected.
We assume that the barbell is in static condition. If the force is exerted at the
end of the barbell, deflection will occurs. The deflection of the barbell can be
finding by using the formula:

PL
AE

Next, we use the value of deflection to get the value of strain using the
equation:

Furthermore, we can calculate the deflection of the member by using the


formula of deflection.

d2 y
EI
=Px
2
dx
The formula must be integrated twice to obtain the slope and the
deflection of the member. The first the integration is to find the slope and the
second integration is to find the deflection.
At structure 2, we can find the stress that act at the upper of barbell stand by
using the equation:

P
A

So, the stress exerted at this position is equal to 20.44 kPa.


At structure 3, there will be buckling act upon the barbell stand. Using E=200
GPa and max=400MPa for A-36 steel material. Using formula:

Pcr=

EI
(KL)

cr=

Pcr
A

The critical stress is equal to 415.61 MPa.


At structure 4 and structure 5, all force can be finding by using the
equilibrium equation:

F=0
M =0
Structure 4 also has load that exerted at barbell stand. The load is
supported by a pin, so we consider all the stress in the pin. By using the
concept of equilibrium in particle, we can find the resultant force at the pin.

We consider the pin is in single shear. So, t o calculate the shear stress
we use the single shear stress formula as below and we get the value of shear
stress

=138.76 MPa .

P
A

Conclusion
Based on this analysis we deduced that the load that exerted to the
material must be appropriate. From this assignment we can conclude that
strength of material is very important in everyday life. Everything surrounding us
is related to equipment that we use. In this structural analysis of gymnasium
equipment we have analysed, we can resolve that this gymnasium equipment is
safe to be use. This is proven after we calculated all the structure, the value
obtained is less than the reference value of this material from the text book.
The machine or this gymnasium equipment can be broke and damaged if
some part of the structure or the supporting holder cant withstand the exert
force from the barbell or other force included. This situation will also may cause
injury to the user.
The main objective of the study of the mechanics of materials is to provide
the future engineer with the means of analysing and designing various machines
and structures. Both the analysis and design of the gymnasium equipment
involve the entire basic of mechanics.
Overall, the fundamental principles learned in the class help us to relate
with the real life occurrences. Besides, we are now able to do analysis and apply
theories to real life problem and situations. Lastly, good teamwork skills among
the member are developed after going through this assignment.

You might also like