The last PCB version:PCB6.

0E:
. Programming EPROM, EEPROM, FLASH Burner (Vpp 12.5V,21V,25V)
. Support CHIPS (EPROM, EEPROM, FLASH,PIC, MCS-51,AVR, ISP),same as willem programmer.
. Support all types of serial EEPROMs in 8-pin package.such as EEPROM I2C (24Cxxx);EEPROM Microwire (93Cxxx)
;EEPROM SPI (25Cxxx, 25LVxxx, 25Fxxx, 25Pxxx).
. Fast programming time
. It can use the power supply from a USB port or DC Adapter.
Deepblue Programmer PCB6.0E feature
Deepblue Programmer PCB6.0E can be use for :
. Upgrading, Programming BIOS chip, Repairing PC motherboard BIOS chip.
. VCD, DVD, Color TV, Copier, Fax machine, Printer main board maintaining or reparing.
. Car memory device code reading, writing
. MCU development: programming for MCS-51 series, AVR series and PIC series MCU.
. Programming support for over 2000 IC devices, includes EPROM , EEPROM , FLASH , PIC , AVR , MCS-51 , MCS-48,
27Cxx , 28Cxx 28Fxx , 29Fxx , AT29Cxxx ,PIC16xxx , DS12xx , AT89Cxx , AT89Cx051 , AT90Sxxx , EPROM16bit ,
29Fx00 , 28Fx00
support all 8-pins serial EEPROMs
supports interfaces IIC (24Cxx), Microwire (93Cxx), SPI (25Cxx)
EEPROM I2C (24Cxxx)
EEPROM Microwire (93Cxxx)
EEPROM SPI (25Cxxx, 25LVxxx, 25Fxxx, 25Pxxx)
Configuration (EE)PROM: AT17xxx, LV series including
speciall devices (digital thermometers, ...)
supports programming LV (3.3V) EEPROM
8182 supported devices by 2.86 version of SW (26. Jan. 2012)
Hardware Features :
. Support DIP32 to PLCC32 and PLCC Firmware HUB/LPC(adapter).
. Support all I2C;Microwire;SPI,
ZIF (Zero Insertion Force) DIL socket,simple SOIC8 and SSOP8 adapter
each pin is possible to set in position Low and H/Pull-up
from each pin is possible to read
support of Low Voltage devices
. Support the chip 29/39/49LVxxx (Low Voltage 3.3V)

. Use power supply from a USB port or DC Adapter (9-12 VDC).

Software Features :
. Windows based programming software support 98 / ME / NT / 2000 / XP
. Latest !! Software willem version 0.98D12 (Update : 13 September 2010).
. Last Elnec Software(ver 2.81) can support 8182 devices.(26. Jan. 2012)
software 98D12
Support CHIPS (EPROM,EEPROM,FLASH,I2C,PIC,MCS-51,AVR, 93Cxx, ISP)
27C64 , 27C128 , 27C256 , 27C512 , 27C010 , 27C020 , 27C040 , 27C1001
M27C1001 , M27C2001 , M27C4001
27C080 (A19) , M27C801 , M87C257
EPROM
2716(Vpp25V) , 2732 , (adapter DIP24)
2764 , 27128 , 27256 , 27512 , 27010,
Vpp12.5V (21Vpp Modify Circuit)
28C65 , 28C64 , 28C128 , 28C256 , 28C512 , 28C010 , 28C020 , 28C040
EEPROM
M28C16A/17A (DIP28)
(Adapter or Jumper) 28C16,XLS2816 (DIP24)
28F64 , 28F128 , 28F256 , 28F512 , 28F010 , 28F020
MX26C1000 , MX26C2000 , MX28F1000 , MX28F2000
FLASH Memory Am28F256A , Am28F512A , Am28F010A , Am28F020A (New command erase/prog.)
-- intel --i28F001BX , 28F004 , 28F008 , 28F016
29F64 , 29F128 , 29F256 , 29F512 , 29F010 , 29F020 , 29F040 , 29F080
FLASH Memory
29F001 , 29F002 , 29F004 , 29F008 , 29F016 , 29F032 , V29C51002T , 29LV040
Serial (I2C)
EEPROM
24Cxx
support more than 8000 devices,down support devices TXT.please click blow link
Serial SPI
http://www.rebios.net/deep%20blue/seepdev.txt
FLASH 25Xxx
Microwire
EEPROM
Microchip PIC 16C84 , 16F84 ,16F84A , 16F627/16F628
12C508/A , 12C509/A , 12CE518 , 12CE519 , 16C505
16C620 , 16C621 , 16C622 , 16CE623 , 16CE624 , 16CE625 , 16C710/711

---ICSP connector---16F870 , 16F871 , 16F872 , 16F873 , 16F874 , 16F876 , 16F877 PIC16F873A , PIC16F874A ,
PIC16F876A , PIC16F877A
-Add PIC microchip 14bit
PIC12F629 , PIC12F675 , PIC16F630 , PIC16F676 , PIC12F635 , PIC12F683 , PIC16F636 ,
PIC16F684 , PIC16F688
PIC16F72/73/74/76/77 , PIC16F737/747/767/777 , PIC16F87/88 , rfPIC12F675x ,
PIC16F785/PS200 , PIC16F716
-Add microchip 14bit,12bit OTP
PIC12C671 , PIC12C672 , PIC12CE673 , PIC12CE674
PIC16C61/71 , PIC16C62/64/65/73 , PIC16C62A/62B/62C/63/63A/64A/65A/65B/66/67
PIC16C72/72A/73A/74A/74B/76/77 , PIC16C620/620A/621/621A/622/622A
PIC16CE/623/624/625 , PIC16C710/711/712/716 , PIC16C773/774 , PIC16C745/765/923/924 ,
PIC16C925/926
PIC16C554/556/557/558 , PIC16C432/433 , PIC16C717/770/771/781/782
-Add PIC microchip 14bit
PIC12F629/675 , PIC16F630/676 , PIC12F635/683 , PIC16F636/684/688 ,
PIC16F72/73/74/76/77 , PIC16F737/747/767/777 , PIC16F87/88 , rfPIC12F675x ,
PIC16F785/PS200 , PIC16F716
-Add microchip 14bit OTP
PIC12C671 , PIC12C672 , PIC12CE673 , PIC12CE674 , PIC16C61/71 ,
PIC16C62/64/65/73 , PIC16C62A/62B/62C/63/63A/64A/65A/65B/66/67 ,
PIC16C72/72A/73A/74A/74B/76/77 , PIC16C620/620A/621/621A/622/622A ,
PIC16CE/623/624/625 , PIC16C710/711/712/716 , PIC16C773/774 ,
PIC16C745/765/923/924 , PIC16C925/926 , PIC16C554/556/557/558 , PIC16C432/433
, PIC16C717/770/771/781/782
-Add PIC microchip 12bit (FLASH memory)
PIC12F508/509 , PIC10F200/202/204/206 , PIC16F505 , PIC16F54/57
-Add PIC18Fxxx
PIC18F242 , 18F248 , 18F252 , 18F258 , 18F442 , 18F448 , 16F452 , 16F458
PIC18F1220 , 18F2220 , 18F4220 , 18F1320 , 18F2320 , 18F4320
PIC18F6520 , 18F6620 , 18F6720 , 18F8520 , 18F8620 , 18F8720
PIC18F2331 , 18F2431 , 18F4331 , 18F4431
PIC18F6525 , 18F6621 , 18F8525 , 18F8621
PIC18F6585 , 18F6680 , 18F8585 , 18F8680

PIC18F2439 , 18F2539 , 18F4439 , 18F4539

PIC18F6410 , 18F8410 , 18F6490 , 18F8490
Add PIC18Fxxx
PIC18F2410 , PIC18F2420 , PIC18F2455
PIC18F2510 , PIC18F2515 , PIC18F2520 , PIC18F2525 , PIC18F2550 , PIC18F2585
PIC18F2610 , PIC18F2620 , PIC18F2680
PIC18F4410, PIC18F4420 , PIC18F4455
PIC18F4510 , PIC18F4515 , PIC18F4520 , PIC18F4525 , PIC18F4550 , PIC18F4585
PIC18F4610 , PIC18F4620 , PIC18F4680
Add Find and edit value OSCCAL (PIC12F629/675 , PIC16F630/676)
Add Edit config at address 0x2008,0x2009 (PIC12F635/683 , PIC16F636/684/688 ,
PIC16F785)
Fixed Programming PIC all
Test on chip
PIC12F675 , PIC16F676 , PIC16F684 ,PIC16F767, PIC16F74
PIC16F872 , PIC16F876 , PIC16F877, PIC16F876A, PIC16F873A, PIC16F819
PIC16F84 , PIC16F84A , PIC16F628, PIC16F628A,
eprom PIC12C509JW , PIC16C505JW , PIC16C711JW , PIC16CE625JW
PIC18F458 , PIC18F4320 , PIC18LF258 , PIC18F4539 , PIC18F4431
AT29C256 , AT29C512 , AT29C010A , AT29C020 , AT29C040 , AT29C040A
Atmel Flash
W29EE512 , W29EE011 , W29EE012 , W29C020(128) , W29C040
Memory
PH29EE010(W29EE011)
(Sector
ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020)
Programming)
Ver 0.992 up(DOS). Can run under win9x
(Software Data
(disable prog. CPUIdle or CPUCool)
Protection)
AT49BV512
Atmel Flash
Command seq. 5555/AA, 2AAA/55, 5555/A0
Memory
AT49F512 , AT49F010 , AT49F020 , AT49F040
AT49Fxxx
SST39SF010 , SST3S9F020 ,SST39SF040
(Subset
AT49F001 , AT49F002 , AT49F008A
29Fxxx)
(Byte-by-Byte
Command seq. 555/AA, 2AA/55, 555/A0
Programming)
Am29F512 , Am29F010 , Am29F020 , Am29F040 , HY29F080
(Software Data
29F002 , 29F002T , Pm29F002T
Protection)

[Atmel] AT25010 , 020 , 040 (A8-A0)

AT25080 , 160 , 320 , 640 , 128 , 256 (A15-A0)
Serial
[ST] W95010....256, Microchip 25x010 - 25x640
Peripheral
--- Byte programming
Interface (SPI) 25010 , 25020 , 25040
EEPROM Mode0 --- Page programming
(0,0)
25C080 , 25C160 , 25C320 , 25C640 , 25C128 , 25C256 , 25C512
AT25xxx,
AT25HP256 , AT25HP512 , M25P10 , M25P20 , M25P40
W95xxx
AT25HP1024 (24bit address)
-- CAT64LCxxx (16bit DATA IN/OUT) use Socket 93Cxxx
CAT64LC010, CAT64LC020, CAT64LC040
Atmel
EEPROM (page
prog.)
AT28C256 , AT28C010 , AT28C040
(Software Data
Protection)
Nonvaltile
DS1220 , DS1225Y , DS1230Y/AB , DS1245Y/AB , DS1249Y/AB
SRAM (DS12xx)
static RAM (Test
6116 , 6264 , 62256 , 62512 , 628128
RAM)
EPROM
W27E512 , W27E010 , W27C010 , W27C020 , W27C040
winbond,SST
SST27SF256 , SST27SF512 , SST27SF010 , SST27SF020
Electrical Erase MX26C4000
Chip
Vcc = 3.3-3.6V SST37VF512 , SST37VF010 , SST37VF020 , SST37VF040
Flash Memory
SST28SF040A , LE28F4001
SST,Sanyo
Support CHIPS : Use together with Adapters
Atmel AT89Cxx (MCS-51)
Atmel Auto Setect
Adapter 32pin to MCS-51
AT89C51 , 52 , 55 , AT89LV51 , 52 , 55
AT89S8252 (8K+2K) , AT89S53 , AT89LS8252 , AT89LS53
AT89C1051 , AT89C2051 , AT89C4051 (20pin)
AT89C51RC (32KB) , AT89C55WD (6.2V)
SST89C54/58 , SI89C52
Intel Auto Select

Atmel AVR 8-bit RISC AT90Sxxx

(Parallel programming)
Adapter 32pin to MCS-51

MCS-48,MCS-41
Adapter 32pin to MCS-48/41

FLASH memory 8/16bit

(Software Data Protection)
Adapter (TSOP48)
FLASH memory 8/16bit (Vpp12V)
(Software Data Protection)
Adapter (TSOP48)
EPROM 16bit (DIP40) (1-4Mbit)
Adapter Eprom 16bit
Eprom only
EPROM 16bit (DIP42) (4-32Mbit)
Adapter Eprom DIP42
Eprom only
FLASH memory 8/16bit
(Software Data Protection)
Adapter (TSOP48LV)
Firmware Hub / LPC FLASH

i87C51 , i87C51FA , i87C51FB

-----------------------------------------------i8xC51 , i8xC52 , i8xC54 , i8xC58 (tWP = 100uS*25 Pulse)
(read , write , erase , verify , checkempty , Lockbits , Fusebits)
[Flash memory/EEPROM]
AT90S1200 , AT90S2313
90S2333 , 90S4433 , 90S4414 , 90S8515 , 90S4434 , 90S8535
reference AT90S2313 pin
Function Lockbit read AT90S2313 Errata Sheet.pdf
ROM (read/verify)
P8048AH , P8049AH,P8050AH , P8042AH Vea = 12V
P8041 , P8042
OTP (read/verify/Progam)
P8748 , P8749H , P8742H Vea = 18V
EPROM (read/verify/Progam)
D8748 , D8749 , D8742 , D8741 , D8742 Vea = 18V
Am29F400 , Am29F800 , 29F160 , 29F320 ,MX29F1610 (read ,
write byte mode)
HY29F200 , HY29F400 , HY29F800 , AT49F2048A , AT49F4096A ,
AT49F8192A
i28F200 , i28F400 , i28F800 , i28F160 (TSOP48)
28F001(DIP32 or PLCC32)
27C1024 (27C210) , 27C2048 (27C2002) , 27C4096 (27C4002),
Schematic by Toomas Toots
(read , Program byte mode
by use Resister pull up Data Bus (0xFF) , A0 select low or high byte)
M27C400(DIP40) , 27C800 , 27C160 , 27C322
Schematic by Toomas Toots
(read , Program byte mode
by use Resister pull up Data Bus (0xFF), A0 select low or high byte)
29LV200 , 29LV400 , 29LV800 , 29LV160 , 29LV320 (read,write byte
mode)
-- Firmware Hub

82802AB , 82802AC , AT49LW040 , AT49LW080

SST49LF002A , SST49LF003A , SST49LF004A , SST49LF008A
Adapter Firmware Hub/LPC (PLCC32) (PP
W49V002FA , W39V040FA
mode) (3.3V)
-- LPC flash
SST49LF020 , SST49LF040
W49V002A , W39V040A
P28F002BC
BOOT BLOCK FLASH MEMORY
Adapter P28F002BC (DIP40)
- P28F002BC
MBM29LV002TA/BA , MBM29LV004 , MBM29LV008 , MBM29LV017 ,
MBM29LV080
TSOP40A
MBM29F002ST/SB , MBM29LV016 , Am29LV004 , Am29LV002 ,
Am29LV008
MBM29F017A , MBM29F016A , MBM29F080 , 28F008SA , 29F004S5
TSOP40B
Am29F080 , Am29F016B , Am29F016 , Am29F017B , Am29F065MU
Adapter

Atmel AT89Cxx (MCS-51)

Adapter 32pin to MCS-51

Atmel AVR 8-bit RISC AT90Sxxx

(Parallel programming)
Adapter 32pin to MCS-51
MCS-48,MCS-41
Adapter 32pin to MCS-48/41

Atmel Auto Setect

AT89C51 , 52 , 55 , AT89LV51 , 52 , 55
AT89S8252 (8K+2K) , AT89S53 , AT89LS8252 , AT89LS53
AT89C1051 , AT89C2051 , AT89C4051 (20pin)
AT89C51RC (32KB) , AT89C55WD (6.2V)
SST89C54/58 , SI89C52
Intel Auto Select
i87C51 , i87C51FA , i87C51FB
-----------------------------------------------i8xC51 , i8xC52 , i8xC54 , i8xC58 (tWP = 100uS*25 Pulse)
(read , write , erase , verify , checkempty , Lockbits , Fusebits) [Flash
memory/EEPROM]
AT90S1200 , AT90S2313
90S2333 , 90S4433 , 90S4414 , 90S8515 , 90S4434 , 90S8535
reference AT90S2313 pin
Function Lockbit read AT90S2313 Errata Sheet.pdf
ROM (read/verify)
P8048AH , P8049AH,P8050AH , P8042AH Vea = 12V

FLASH memory 8/16bit

(Software Data Protection)
Adapter (TSOP48)
FLASH memory 8/16bit (Vpp12V)
(Software Data Protection)
Adapter (TSOP48)
EPROM 16bit (DIP40) (1-4Mbit)
Adapter Eprom 16bit
Eprom only
EPROM 16bit (DIP42) (4-32Mbit)
Adapter Eprom DIP42
Eprom only
FLASH memory 8/16bit
(Software Data Protection)
Adapter (TSOP48LV)

P8041 , P8042
OTP (read/verify/Progam)
P8748 , P8749H , P8742H Vea = 18V
EPROM (read/verify/Progam)
D8748 , D8749 , D8742 , D8741 , D8742 Vea = 18V
Am29F400 , Am29F800 , 29F160 , 29F320 (read , write byte mode)
HY29F200 , HY29F400 , HY29F800 , AT49F2048A , AT49F4096A ,
AT49F8192A
i28F200 , i28F400 , i28F800 , i28F160 (TSOP48)
28F001(DIP32 or PLCC32)
27C1024 (27C210) , 27C2048 (27C2002) , 27C4096 (27C4002),
Schematic by Toomas Toots
(read , Program byte mode
by use Resister pull up Data Bus (0xFF) , A0 select low or high byte)
M27C400(DIP40) , 27C800 , 27C160 , 27C322
Schematic by Toomas Toots
(read , Program byte mode
by use Resister pull up Data Bus (0xFF), A0 select low or high byte)
29LV200 , 29LV400 , 29LV800 , 29LV160 , 29LV320 (read,write byte mode)
-- Firmware Hub
82802AB , 82802AC , AT49LW040 , AT49LW080

Firmware Hub / LPC FLASH

SST49LF002A , SST49LF003A , SST49LF004A , SST49LF008A
Adapter Firmware
W49V002FA , W39V040FA
Hub/LPC (PLCC32) (PP mode) (3.3V)
-- LPC flash
SST49LF020 , SST49LF040
W49V002A , W39V040A , PT49V004
P28F002BC
BOOT BLOCK FLASH MEMORY
Adapter P28F002BC (DIP40)
- P28F002BC
TSOP40A
MBM29LV002TA/BA , MBM29LV004 , MBM29LV008 , MBM29LV017 ,
MBM29LV080
MBM29F002ST/SB , MBM29LV016 , Am29LV004 , Am29LV002 ,

TSOP40B

Am29LV008
MBM29F017A , MBM29F016A , MBM29F080 , 28F008SA , 29F004S5
Am29F080 , Am29F016B , Am29F016 , Am29F017B ,
Am29F065MUPCB6.0C EPROM Program Operating Manual

1.The ZIF Socket for 5V devices

2.The ZIF Socket for FWH/LPC devices
3.1.The ZIF Socket for I2C,93CXX,SPI 25XXX,25CXX devices
4.DIP switch (see window STATUS of software)
5.The 25 Sub D cable
6.The USB cable for power supply
7.The DC cable for power supply
2.Hardware connection
1.Connect to the printer port with a 25 SubD cable,the cable should not be longer
than 1.8 meter(6 feet standard cable).
This must be a fully wired 1:1 cable,a null modem or serial cable won't work.
2.Connect the power supply with a USB cable or DC power,the power led(green) must go on.
3.Run the software
1.Install the setup.exe,and run the software.(last software ver is 0.98D12)

Click menu Help-hardware test to test hardware and connection.hardware test fail,Causes:
Hardware test fail,Causes:
1.The connect of printer port is error.
2.The connect of power supply is error.

4.Select a device
1.Selecting the IC number that you want to program by using menu DEVICE or click the button
for normal 5V device,put the chip to ZIP1.

for FWH/LPC device,put the device to ZOP2.

2.For the IC type 8-pin,18-pin setting DIPswitch doesn't need, but for the IC type 28-pin, 32-pin you have to set the DIPswitch same as the
DIPswitchsetting picture.
3.Toolbar menu and Action menu description

5.Programing or read data

Programing Data ( EPROM,EEPROM,FLASH,PIC )
1. Select device type (Menu Device)
2. Set the DIP switch (see window STATUS).DIPswitch switches can be red(like in the sofware),white or other colors.
3. Load program file (Menu File -> Load xxx)
4. Insert the IC to the ZIF Socket or the DIP socket
5. For Eprom 27Cxxx,27xxx make sure you earase all data (UV erase) by use (Menu Action -> Checkempty)
Flash,Eeprom erase data by (Menu Action -> Erase 28x, 29x, 49x, AT89x)
PIC check parameter setting first by use (Menu Progsettings)
6. Program (Menu Action -> Program)
Reading Data ( EPROM,EEPROM,FLASH,PIC )
1.
2.
3.
4.
5.

Select device type (Menu Device)

Set the DIP switch (see window STATUS)
Insert the IC to the ZIF Socket or the DIP socket
Read data (Menu Action -> Read)
Save data, You can save as two types 1. binary(.bin) or 2. Intel hex (.hex) (Menu File ->Save xxx)

Programming MCS-51 (Adapter board is needed

1.
2.
3.
4.
5.

Select pin type (40 or 20pin) and number program (Menu Device)
Set the DIP switch (see window STATUS).
Insert the IC to Adaptor board
Select device type. For ATMEL chip you can read the ID code and set parameters automatically (auto select)
Load program file (Menu File -> Load xxx)

6. Erase old program existing in the IC (Menu Action -> Erase 28C,29C,AT89)
7. Burn program (Menu Action -> Program)
8. Protect your data ( protect from copying ) (Menu Action ->Lock Bit)
Programm SPI FLASH(25XXX)
When programing 24XXX/25XXX/93XXX,set J4 to SPI.
1.run Elnec software 2.86

2.select SPI FLASH/EEPROM

3.Insert the IC to the 25XXX Socket

3.read or programm data