Box Contents

The following items are included in the HC-800 box:

HC-800 Controller

HC-800 Controller
Installation Guide

AC to DC power adapter with power cord

IR emitters (6)
Antennas (3): ZigBee (1) and dipole antennas (2)
for wireless (WiFi).
Pluggable Contact/Relay connectors (2)
Warranty Card

Accessories for Purchase

Rack Ear Kit (C4-1UREK-B)
10 Antenna Kit (C4-AK-3M)

Warnings
Supported Model
C4-HC800-BL HC-800 Controller, Black

Introduction
The Control4 HC-800 Controller (HC-800) provides
ways to control lights, home theaters, wholehome music and video systems, and other devices
controlled by IP, infrared (IR), Serial, Contact, or Relay
connections. The Controller has a fast processor,
built-in WiFi, HDMI for audio and video, improved
ZigBee radio, and more.
The HC-800 also provides extensive media
management support for audio and video content,
including CDs, DVDs, Blu-ray Discs, or digital media
stored in connected devices. You can use an external
storage device with USB, NAS, or eSATA connectivity,
and it supports multi-zone audio capabilities, sending
music to various rooms in the home. The device can
be stacked with AV devices or rack-mounted using
the optional rack ears.
After you install and configure the HC-800 (using
the Composer Pro software) along with the other
system components, your customers can control their
system using the On-Screen Navigator, the MyHome
app, System Remote Controls, Touch Screens, or any
other Control4-supported interface devices (sold
separately).

WARNING! To reduce the risk of electrical

shock, do not expose this apparatus to rain or
moisture.
AVERTISSEMENT! Pour rduire le risque de
choc lectrique, nexposez pas cet appareil la
pluie ou lhumidit.
WARNING! This CLASS I apparatus must
be connected to an AC mains socket outlet
that has a protective earthing connection
(e.g., third-prong ground conductor). DO
NOT DEFEAT THE PROTECTIVE EARTHING
CONNECTION!
AVERTISSEMENT! Cette appareil de classe I
doit tre raccord une prise de courant qui
a une connexion Mise la terre (par exemple,
conducteur avec troisime broche). NE PAS
DFAIRE LA CONNEXION DE MISE LA
TERRE!
For general information about the product, see the
Product pages at http://www.control4.com.

Requirements and Specifications

Prior to installing the HC-800, ensure that Ethernet
network wiring is in place. If youre using WiFi, see
Antenna Considerations which includes information

Additional Resources
The following resources are available for additional
support.

HC-800 Controller
Installation Guide

Control4 Knowledgebase or Forums

Control4 Technical Support
Control4 website: http://www.control4.com
Composer documentation in online help or PDF
format available on the Dealer portal (http://
dealer.control4.com/).

about ZigBee Access Points (ZAPs).

Front View
Figure 1. Front View

HC-800 Specifications
WIFI

Model Number

C4-HC800-BL

Network

- Ethernetrequired
- WiFi (only supported when the
device is used as a Secondary
Controller)

Media Recognition

Online CD/DVD/Blu-ray
recognition and media information
service. Supports MP3, AAC, FLAC.

Video

HDMI 1.4 output; Component Video

output; SD 480I; HD 720p 50-60
Hz.

Colors for signal strength: Orange=Fair to Good,

Power Requirements

100-240 VAC, 60/50 Hz, 0.4A MAX

DC Input: 19V DC

Power Consumption

Max: 44W, 150 BTUs/hour

Idle: 24W, 82 BTUs/hour

Operating Temperature

3- 95 F (0 - 35 C)

Storage Temperature

-4 - 149 F (-20 - 65 C)

IR Out

5V 27mA, max/output

IR Capture

0-60KHz

Contacts

DC - 36V maximum operation (low

voltage)
The available current for 12V
contact outputs is 1.25A maximum,
shared across all outputs.

Weight

6.1 pounds (2.766 kg)

Shipping Weight

7.95 pounds (3.606 kg)

WiFi LED. This LED blinks Orange and then Blue

of its connection to its associated access point.

LED indicators

H x W x D: 2.80 (71 mm) x 11.98

(304 mm) x 7.24 (184 mm)

the LED color depending on the signal strength

Display

Dimensions

system starts running, the WiFi driver changes

MP3: 32kbps to 320kbps, CBR,

VBR, AAC, and FLAC

AC - 36V, 2A
DC - 24V, 2A
Maximum operation (low voltage)

LINK

during the boot process. When the operating

Audio Playback Formats

Relays

DATA

Blue=Excellent, No Light=No connection or not

enabled, and Red=Poor signal strength.
Data LED. The Blue LED indicates that streaming
audio is received.
Link LED. The Blue LED indicates that the
Controller has been identified into a project.
4

Power LED. The Blue LED indicates that AC

power is present. The LED blinks during the boot
process.

IR Window/IR BlasterFor learning IR codes.

Back View
Connect all applicable devices to the HC-800 using
the connection options described next.

Figure 2. Back View

10 Digital Audio Out. Digital audio output jack

for stereo line output for amplifiers or audio

16

switches.
11 Audio Out. RCA jacks for stereo channel
line output (line level) for amplifiers or audio

1
2

6
5

10
9

12
11

14

17

switches.
12 Audio In. (One (1) pair). RCA jacks for stereo

18

13
15

channel input (line level) for one (1) stereo analog

19

source.
13 eSATA. External serial ATA port for connecting a
hard drive on which to store media. See Setting

ZigBee. The antenna for the ZigBee radio.

up External Storage Devices for information. For

information about eSATA storage limitations, see

NOTE: If you run ZigBee, use the external

antenna (provided).

eSATA Installation Guide in the Knowledgebase.

14 Ethernet. RJ-45 jack for a 10/100/1000 BaseT
Ethernet connection.

2
3

Power Plug Port. AC to DC power adapter for the

15 USB. For external storage device with USB

power cord.

support. See Setting up External Storage

Factory Restore Button. A recessed button that

Devices for information. For information

restores or resets the Controller to the factory

about USB storage limitations, see the eSATA

defaults. See Troubleshooting for details.

4

Identification Button. An easily-pressed button

Installation Guide in the Knowledgebase.

16 Relays. Pluggable terminal block connector for

used to identify this device in Composer Pro to

four (4) switchable connections, such as a blind,

revert the device back to Ethernet with its default

a fireplace, or a projector screen. The connectors

settings.

are for Normally Opened (NO), Normally Closed

RS-232 Serial. DB9 connectors for two (2) serial

(NC), and Common (COM).

devices, such as a receiver or disc changer. See

17 Power. For troubleshooting purposes only. After

Connect the Serial Ports for information.

6

transmitters. See Set Up IR Emitters or IR

7

plugging in the HC-800, it it does not power on,

IR Out. 3.5 mm jacks for up to six (6) IR output

insert a paper clip into the pinhole to power it on.

18 Contacts. Pluggable terminal block connector for

Blaster for information.

four (4) Normally Closed or Normally Opened

HDMI Out (Audio/Video). HDMI port for

switchable connections. Provides power for small

displaying navigation menus on a monitor or TV.

devices (12V), signal input (SIG), and return path

(GND).

NOTE: HDMI and Component cords can be

19 WiFi 2. Reverse SMA Connector to attach a WiFi

connected at the same time, but only one is

antenna.

active.
NOTES: (1) WiFi cannot be used for Primary
8

Video Out (Component). Component jack used

Controllers; use WiFi for Secondary Controllers

for displaying navigation menus on a monitor or

only. See Antenna Considerations below. (2)

TV.

For best results, we recommend that you use

WiFi 1. Reverse SMA connector to attach a WiFi

802.11 n.

antenna. Supports 802.11 b/g/n.

Installation Instructions
NOTES: (1) WiFi cannot be used for Primary
Controllers; use WiFi for Secondary Controllers

To install this Controller:

only. See Antenna Considerations below. (2)

For best results, we recommend that you use
802.11 n.

Ensure that your home network is in place before

starting your system setup. The HC-800 requires
a network connection (wired or WiFi) to use
3

all features as designed. When connected, the

To connect a device to the Pluggable Terminal Block:

Controller can connect to other IP devices on

the home network and access web-based media

Insert one of the wires required for your device

into the appropriate opening in the Pluggable

more information, see the Knowledgebase article

Terminal Block you reserved for that device (see

#3 about recommended networking hardware.

Figure 3).

Mount options. The HC-800 is designed to be

stackable with other AV equipment or mounted

databases and Control4 system updates. For

Insert the wire as follows:

If using solid core wire, push the wire into the

in a rack or on a shelf using the optional Rack Ear

hole below the slotted retention tab, and ensure

Kit (C4-1UREK-B, sold separately).

that its tightly secured.

Connect the HC-800 to the network. To connect

If using stranded wire, push the slotted retention

using an Ethernet connection, plug the data

tab in using a small flat-blade screwdriver. Insert

cable (Ethernet cable or RJ-45 patch cable)

the wire into the hole below the tab, and then

from the home network connection into the

release the tab to secure the wire (see Figure 3).

Controllers RJ-45 port (labeled Ethernet) and

the network port on the wall or at the network

Figure 3. Connect to Terminal Block

switch.
4

Power up the Controller. Plug the HC-800 power

cord (provided) into the Controllers power plug
port and an electrical outlet.
NOTES: (1) Only use the power supply
included in this box. (2) The HC-800 may
take several minutes to boot up and become
operational. Please allow sufficient time for
bootup. This LED blinks Orange and then Blue
during the bootup process.

EXAMPLE: If you add a motion sensor (see

Figure 5), connect its wires to the following

Connect system devices. Attach the devices as

Contact openings:

described in Connect the Devices below.

6

Set up any external storage devices as described

Power input to +12V

in Setting up External Storage Devices.

Output signal to SIG

Ground connector to GND

Connect the Devices

See the following sections for instructions about

connecting the various protocols.

NOTE: Use Composer Pro to step through

the connection process before or after the
Controller is physically connected.

Repeat Steps 1 and 2 for all wires required for

your device.

The following section provides more information

about other connection options.

NOTE: If you connect dry contact closure

devices, such as doorbells, connect the switch

Pluggable Terminal Block Connectors

For the Contact and Relay ports, the HC-800 makes

between +12V (Power) and SIG (Signal).

Connect to the Contact Port

use of a pluggable terminal block connectora

removable plastic part that locks in individual wires

The HC-800 provides four (4) contact ports for the

(included).

pluggable terminal block provided.

See Figures 4 through 8 to learn how to connect the

Figure 8. Relay Port, Normally Closed

NC

NO

+12V

SIG

GND

Figure 4. Contact Port for Voltage Source (e.g.,

COM

device to a contact port.

RELAYS

Motion Sensor)
NO

NC

COM

CONTACTS

RELAYS

Connect the Serial Ports

CONTACTS
GND

SIG

+12V

The HC-800 has two (2) DB9-style serial ports.

Sensor)

changer, to the HC-800 by aligning the pins and

NC

NO

Connect a device, for example, a receiver or disc

COM

Figure 5. Contact for Dry Contact (e.g., Door Contact

tightening the screws.

RELAYS

See the next table for serial communication values.

CONTACTS

Odd
Parity

Even
Parity

No Parity

Serial Port 1

Serial Port 2

GND

SIG

+12V

Figure 6. Contact for Self-Powered Voltage Source

NO

NC

COM

Device

Hardware
Flow
Control

Set Up IR Emitters or IR Blaster

RELAYS

The system may contain third-party products

that are controlled with IR commands (usually

CONTACTS
GND

SIG

+12V

through remote controls). To provide a way for the

Controller to control a device that only recognizes IR

Connect to the Relay Port

The HC-800 provides four (4) relay ports for the
pluggable terminal block provided. With most

commands, complete one of these setups for

IR Emitters
IR Blaster

applications, attach one (1) wire to the common

NOTE: All IR ports deliver the same amount of

terminal and the other to the Normally Opened

power.

terminal. The relay switches close when the relay is

activated.

IR Emitters

The HC-800 can support applications that require a

Normally Closed contact.

Plug the 3.5 mm connector end of one of the six

(6) IR stick-on emitters provided into an IR Out

Figure 7. Relay Port, Normally Open

port on the HC-800.

2

Place the stick-on emitter end over the IR

NO

NC

COM

receiver on the Blu-ray player, TV, or other target

device to drive IR signals from the HC-800 to the

RELAYS

target.

CONTACTS
GND

+12V

SIG

IR Blaster

Install in a Rack (Optional)

In addition to IR emitters, the HC-800 is also

To install the Controller in a rack (front or back):

equipped with an IR blaster located just left of the

front LEDs.

screws that secure the feet (each corner on the

To use the blaster rather than an IR emitter:

1

In Composer, connect the Front IR Blaster Out

on the Controller to the IR In for the device you

Controller).
2

Remove the rubber feet.

Use the same screws to attach the rack ears

(Rack Ear Kit, C4-1UREK-B, sold separately) into

want to control.
2

Test and verify that the HC-800 is positioned in

such a way that the blaster can reach the device
you want to control.

Antenna Considerations
Depending on the location of the HC-800 and the
network setup, youll need to consider which, if any,
antennas to connect to the HC-800.

Turn the Controller over and remove the four (4)

the screw holes.

4

Attach the Controller to the rack.

Setting Up External Storage Devices

You can store and access media from an external
storage device, for example, a NAS or eSATA drive, or
USB memory device by plugging the USB drive into
the USB port and then configuring and scanning the
media (if required) in Composer Pro. For information
about adding storage devices, see eSATA Installation

Not Using WiFi

Guide in the Knowledgebase.

In this case, the standard CAT5 Ethernet cable works

NOTE: When using eSATA or USB storage

well with the HC-800 installed on a rack. No WiFi

devices on an HC-800, you can only use one

antenna is required.

(1) partition with a 2TB maximum size. This

limitation applies to the USB storage on all

Using as a ZigBee Access Point (ZAP)

Attach one (1) of the antennas provided to the HC800 RSMA connector labeled ZigBee as needed.
If the HC-800 is mounted in a metal rack, use the

other Controllers also.

Composer Information

optional 10 Antenna Kit (C4-AK3M, sold separately).

Driver. Choose the Home Controller HC-800

driver in Composer (OS 2.2 and later) and add
it to your project. See Composer Pro Getting

Using with a WiFi Connection

Started for details.

In this case, youre connecting the HC-800 wirelessly.

Properties. There is a special section for

configuring the video resolution. Select the video
output you are using from the Connections

NOTES: (1) This option is not recommended

view (HDMI or Component), and then select the

if the HC-800 is mounted in a rack. (2) WiFi

preferred video mode. The default is 720p @ 60

is not supported on HC-800s as Primary

Hz for Component and HDMI. HDMI also uses

Controllers.

auto configuration to select the best possible

resolution for the display device. After making

Use the WiFi antenna when you dont have an

the selection, click Set Resolution. If the video

Ethernet connection, and youre using the HC-800 as

resolution has to change, the Controller will

a Secondary Controller.

reboot; this is normal. See Configuring an HCClass Controller in the Composer Pro User Guide

NOTE: For best results, we recommend that

you use 802.11 n.

on the Dealer website for more details.

Troubleshooting

Regulatory/Safety Information

Factory Restore Button

To review regulatory information for your particular

Control4 products, see the information located on

CAUTION! The Factory Restore process will

the Control4 website at: http://www.control4.com/

remove the Composer project.

regulatory/.

To restore the HC-800 for system recovery to the

Warranty

factory default image, perform the following steps:

Limited 2-year Warranty. Go to http://www.control4.

Insert one (1) end of a paper clip into the small

com/warranty for details.

hole on the back of the HC-800 that is labeled

Factory Restore.
2

Hold the button until the WiFi Status LED blinks

Orange, and then release it. This should take five

About This Document

Part number: 200-00241, Rev. D, 11/13/2012

(5) to seven (7) seconds. The Status LED will

blink Orange while the restore is running.
Identification Button
Identify. Press the Identification button to
identify the device to the system.
Network and Password Resets. To reset the HC800 to the network and password defaults, hold
the ID button and apply power to the unit. Wait
for either a prompt on the display/monitor or
wait for the Power, Link, and Data LEDs to all turn
on (solid) at the same time. Immediately release
the button and the network and password will be
reset.
Boots/Reboots. Press and hold the Identification
button for five (5) seconds to initiate a Controller
reboot. This sequence of LEDs follows:
- The Power LED blinks briefly, and then turns
solid Blue.
- The Link LED blinks Blue briefly, and then turns
off.
- The Data LED blinks once, and then turns off.
- The WiFi LED blinks Orange, blinks Blue until
the system reboots, and then turns off.
If the device is configured for WiFi, the WiFi
LED reports the status (Red=Bad; Orange=OK;
Blue=Good).

control4.com |

2012 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of Control4 Corporation in
the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.