Scribd
Upload
208 views6 pages

Fully Automatic Rain Sensing Viper

This document proposes a fully automatic rain sensing wiper system called VIPER. It aims to upgrade older car systems by providing automatic wiping controlled by a sensor and actuator, rather than manual control. The system would use a peripheral interface controller and water sensor to automatically adjust wiper speed based on rain detection. This would improve safety by allowing drivers to focus on driving instead of manually operating the wipers. The document describes the concept and working of the proposed automatic system.

Uploaded by

ArunMss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
208 views6 pages

Fully Automatic Rain Sensing Viper

This document proposes a fully automatic rain sensing wiper system called VIPER. It aims to upgrade older car systems by providing automatic wiping controlled by a sensor and actuator, rather than manual control. The system would use a peripheral interface controller and water sensor to automatically adjust wiper speed based on rain detection. This would improve safety by allowing drivers to focus on driving instead of manually operating the wipers. The document describes the concept and working of the proposed automatic system.

Uploaded by

ArunMss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

FULLY AUTOMATIC RAIN SENSING

VIPER
ABSTRACT

AravindRaj(120021601020)
Arunkumar(120021601023)
Avinash(120021601029)

Wiper is an essential component that used to wipe raindrops or


any water from the vehicles windscreen. The previous system
used to activate the wiper manually and the process of pulling up
the wiper is difficult to be handled. Thus, this system is proposed
to solve these problems. The objectives of this project are to
upgrade the older cars system by providing automatic wiping
system, to improve the system by using sensor with actuator and
to design a basic program that will fully operate with the system.
The concept of this proposed wiper system is similar with other
existing conventional wiper. In spite of removing water from
windscreen, this system also will be upgraded to an automatic
control system by using a Peripheral Interface Controller and
water sensor.

1. INTRODUCTION
Wiper is an essential component that used to wipe the raindrops
or any water from the windscreen. Wipers are designed and made
to clear the water from a windscreen. Most of cars have two
wipers on the windscreen, one on the rear window and the other
on each headlight. The wiper parts visible from outside the car are
the rubber blade, the wiper arm holding the blade, a spring
linkage, and parts of the wiper pivots.
2.PROBLEM STATEMENT
Existing system manually used control stalk to activate wiper and
the process of pulling up wiper is difficult to be handled. The
driver needs to switch on and off the control stalk and it will
reduce the drivers concentration during the driving. Thus, this
system is proposed to solve all these problems. The concept of
this wiper system is similar with other conventional wiper, yet this
system will be upgraded to an automatic control system by using
a controller. This will help the driver to give more concentration
and reduce the car accident probability.
CONCEPTUAL DESIGN :
The conceptual design is used at the back windscreen
with a single wiper. The prototype of an automatic wiper is using
the back door of a small hatchback car. From this conceptual
design, the actuator from lock door is used as tools to pull up and
push down the wiper during the engine stop.

PROCDEURE:
The controlled wiper automatically by the Rain Tracker Windshield
Wiper Control System. It (Z8 BIAC 010) operated in parallel with
the existing wiper system. The Rain Tracker will sense rain, snow
or road spray hitting the windshield, and it will automatically run
the wipers at the right speed. By using Rain Tracker, it will ease
the car driver to turn on and off the wiper, so that the users do
not have to take hands off the wheel or other control to adjust the
wipers as road conditions change.
It senses all kind of precipitation such as rain, mist, snow or sleet
and can operate in full range from off through intermittent, slow
and fast speeds. The Rain Tracker uses beams of infrared light to
sense how much water hits the windscreen. It constantly adjusts
the speed of the wipers so that they run just often enough to keep
the windshield clear from all the way off to the high speed

4. CONCLUSION
As the conclusion for the project, the results shows all the
aim objectives of the project. This project showed a contribution
on the design of the automatic wiper system for the future
research in this field. For the future improvement, it is
recommended the system to have literature review on the
material been used as the wiper, because the material used is still
has a problem in the procure issues especially for the hot and
climate country. Other suggestion for designing automatic push
up wiper for future research and improvement is about the design
stand for the wiper.

You might also like